This register performs mapping from overlay ECN to underlay ECN during
IPinIP encapsulation.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a trap for packets that the device decided to drop because they are
not supposed to be routed. For example, IGMP queries can be flooded by
the device in layer 2 and reach the router. Such packets should not be
routed and instead dropped.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add packet trap that can report packets that reached the router, but are
non-routable. For example, IGMP queries can be flooded by the device in
layer 2 and reach the router. Such packets should not be routed and
instead dropped.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add test cases to check that packets routed through disabled RIFs and
packets routed from disabled RIFs are dropped and devlink counters
increase when the action is trap.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IRIF_DISABLED and ERIF_DISABLED are driver specific traps. Packets are
dropped for these reasons when they need to be routed through/from
existing router interfaces (RIF) which are disabled.

Add devlink driver-specific traps and mlxsw trap IDs used to report
these traps.
Signed-off-by: NAmit Cohen <amitc@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Saeed Mahameed says:

====================
Mellanox, mlx5 E-Switch chains and prios

This series has two parts,

1) A merge commit with mlx5-next branch that include updates for mlx5
HW layouts needed for this and upcoming submissions.

2) From Paul, Increase the number of chains and prios

Currently the Mellanox driver supports offloading tc rules that
are defined on the first 4 chains and the first 16 priorities.
The restriction stems from the firmware flow level enforcement
requiring a flow table of a certain level to point to a flow
table of a higher level. This limitation may be ignored by setting
the ignore_flow_level bit when creating flow table entries.
Use unmanaged tables and ignore flow level to create more tables than
declared by fs_core steering. Manually manage the connections between the
tables themselves.

HW table is instantiated for every tc <chain,prio> tuple. The miss rule
of every table either jumps to the next <chain,prio> table, or continues
to slow_fdb. This logic is realized by following this sequence:

1. Create an auto-grouped flow table for the specified priority with
    reserved entries

Reserved entries are allocated at the end of the flow table.
Flow groups are evaluated in sequence and therefore it is guaranteed
that the flow group defined on the last FTEs will be the last to evaluate.

Define a "match all" flow group on the reserved entries, providing
the platform to add table miss actions.

2. Set the miss rule action to jump to the next <chain,prio> table
    or the slow_fdb.

3. Link the previous priority table to point to the new table by
    updating its miss rule.

Please pull and let me know if there's any problem.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

found a warning by the following command:
./scripts/checkpatch.pl -f drivers/net/phy/adin.c

WARNING: msleep < 20ms can sleep for up to 20ms; see Documentation/timers/timers-howto.rst
 #628: FILE: drivers/net/phy/adin.c:628:
+	msleep(10);
Signed-off-by: NDejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vladimir Oltean says:

====================
Rate adaptation for Felix DSA switch

When operating the MAC at 2.5Gbps (2500Base-X and USXGMII/QSXGMII) and
in combination with certain PHYs, it is possible that the copper side
may operate at lower link speeds. In this case, it is the PHY who has a
MAC inside of it that emits pause frames towards the switch's MAC,
telling it to slow down so that the transmission is lossless.

These patches are the support needed for the switch side of things to
work.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the serdes link is set to 2500 using interfce type 2500base-X, lower
link speeds over on the line side should still be supported.
Rate adaptation is done out of band, in our case using AQR PHYs this is
done using flow control.
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Flow control is used with 2500Base-X and AQR PHYs to do rate adaptation
between line side 100/1000 links and MAC running at 2.5G.

This is independent of the flow control configuration settled on line
side though AN.

In general, allowing the MAC to handle flow control even if not
negotiated with the link partner should not be a problem, so the patch
just enables it in all cases.
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pablo Neira Ayuso says:

====================
Netfilter updates for net-next

The following patchset contains Netfilter updates for net-next, they are:

1) Incorrect uapi header comment in bitwise, from Jeremy Sowden.

2) Fetch flow statistics if flow is still active.

3) Restrict flow matching on hardware based on input device.

4) Add nf_flow_offload_work_alloc() helper function.

5) Remove the last client of the FLOW_OFFLOAD_DYING flag, use teardown
   instead.

6) Use atomic bitwise operation to operate with flow flags.

7) Add nf_flowtable_hw_offload() helper function to check for the
   NF_FLOWTABLE_HW_OFFLOAD flag.

8) Add NF_FLOW_HW_REFRESH to retry hardware offload from the flowtable
   software datapath.

9) Remove indirect calls in xt_hashlimit, from Florian Westphal.

10) Add nf_flow_offload_tuple() helper to consolidate code.

11) Add nf_flow_table_offload_cmd() helper function.

12) A few whitespace cleanups in nf_tables in bitwise and the bitmap/hash
    set types, from Jeremy Sowden.

13) Cleanup netlink attribute checks in bitwise, from Jeremy Sowden.

14) Replace goto by return in error path of nft_bitwise_dump(), from
    Jeremy Sowden.

15) Add bitwise operation netlink attribute, also from Jeremy.

16) Add nft_bitwise_init_bool(), from Jeremy Sowden.

17) Add nft_bitwise_eval_bool(), also from Jeremy.

18) Add nft_bitwise_dump_bool(), from Jeremy Sowden.

19) Disallow hardware offload for other that NFT_BITWISE_BOOL,
    from Jeremy Sowden.

20) Add NFTA_BITWISE_DATA netlink attribute, again from Jeremy.

21) Add support for bitwise shift operation, from Jeremy Sowden.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates 2020-01-17

This series contains updates to igc, i40e, fm10k and ice drivers.

Sasha fixes a typo in a code comment that referred to silicon that is
not supported in the igc driver.  Cleaned up a defined that was not
being used.  Added support for another i225 SKU which does not have an
NVM.  Added support for TCP segmentation offload (TSO) into igc.  Added
support for PHY power management control to provide a reliable and
accurate indication of PHY reset completion.

Jake adds support for the new txqueue parameter to the transmit timeout
function in fm10k which reduces the code complexity when determining
which transmit queue is stuck.

Julio Faracco makes the similar changes that Jake did for fm10k, for
i40e and ice drivers.  Added support for the new txqueue parameter in
the transmit timeout functions for i40e and ice.

Colin Ian King cleans up a redundant initialization of a local variable.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable xmit_done is being initialized with a value that is never
read and it is being updated later with a new value. The initialization
is redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The scope of function .ndo_tx_timeout was changed to include the hang
queue when a TX timeout event occurs. See commit 0290bd29
("netdev: pass the stuck queue to the timeout handler") for more
details. Now, drivers don't need to identify which queue is stopped.
Drivers can simply use the queue index provided by dev_watchdog and
execute all actions needed to restore network traffic. This commit do
some cleanups into Intel ice driver to remove a redundant loop to find
stopped queue.
Signed-off-by: NJulio Faracco <jcfaracco@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The scope of function .ndo_tx_timeout was changed to include the hang
queue when a TX timeout event occurs. See commit 0290bd29
("netdev: pass the stuck queue to the timeout handler") for more
details. Now, drivers don't need to identify which queue is stopped.
Drivers can simply use the queue index provided by dev_watchdog and
execute all actions needed to restore network traffic. This commit do
some cleanups into Intel i40e driver to remove a redundant loop to find
stopped queue.
Signed-off-by: NJulio Faracco <jcfaracco@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make use of the new txqueue parameter to the .ndo_tx_timeout function.
In fm10k_tx_timeout, remove the now unnecessary loop to determine which
Tx queue is stuck. Instead, just double check the specified queue

This could be improved further to attempt resetting only the specific
queue that got stuck. However, that is a much larger refactor and has
been left as a future improvement.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

PHY power management control should provide a reliable and accurate
indication of PHY reset completion and decrease the delay time
after a PHY reset
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

TCP segmentation offload allows a device to segment a single frame
into multiple frames with a data payload size specified in socket buffer.
As a result we can now send data approximately up to seven percents fast
than was previously possible on my system.
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for blank NVM SKU
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the unused IGC_FUNC_0 definition and make the code cleaner
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix typo in a context descriptor comment
Signed-off-by: NSasha Neftin <sasha.neftin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Mark function parameters as 'const' where possible.
Signed-off-by: NGuillaume Nault <gnault@redhat.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The felix_parse_ports_node function was tested only on device trees
where all ports were enabled. Fix this check so that the driver
continues to probe only with the ports where status is not "disabled",
as expected.

Fixes: bdeced75 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some PHYs like VSC8234 don't like it when AN restarts on their system side
and they restart line side AN too, going into an endless link up/down loop.
Don't restart PCS AN if link is up already.

Although in theory this feedback loop should be possible with the other
in-band AN modes too, for some reason it was not seen with the VSC8514
QSGMII and AQR412 USXGMII PHYs. So keep this logic only for SGMII where
the problem was found.

Fixes: bdeced75 ("net: dsa: felix: Add PCS operations for PHYLINK")
Suggested-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At least some PHYs (AQR412) don't advertise copper-side link status
during system side AN.

So remove this duplicate assignment to pcs->link and rely on the
previous one for link state: the local indication from the MAC PCS.

Fixes: bdeced75 ("net: dsa: felix: Add PCS operations for PHYLINK")
Signed-off-by: NAlex Marginean <alexandru.marginean@nxp.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver is named "mlxsw", not "mlx5".

Fixes: d4255d75 ("devlink: document info versions for each driver")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is not an error to unplug a cable from the ENETC port even with TSN
offloads, so don't spam the log with link-related messages from the
tc-taprio offload subsystem, a single notification is sufficient:

[10972.351859] fsl_enetc 0000:00:00.0 eno0: Qbv PSPEED set speed link down.
[10972.360241] fsl_enetc 0000:00:00.0 eno0: Link is Down

Fixes: 2e47cb41 ("enetc: update TSN Qbv PSPEED set according to adjust link speed")
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some bits of static data should have been made const from the start.
This change adds the const qualifier where appropriate.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NAlexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_INET is not set and CONFIG_NETDEVSIM=y.
Building drivers/net/netdevsim/fib.o will get the following error:

drivers/net/netdevsim/fib.o: In function `nsim_fib4_rt_hw_flags_set':
fib.c:(.text+0x12b): undefined reference to `fib_alias_hw_flags_set'
drivers/net/netdevsim/fib.o: In function `nsim_fib4_rt_destroy':
fib.c:(.text+0xb11): undefined reference to `free_fib_info'

Correct the Kconfig for netdevsim.
Reported-by: NHulk Robot <hulkci@huawei.com>
Fixes: 48bb9eb4 ("netdevsim: fib: Add dummy implementation for FIB offload")
Signed-off-by: NHongbo Yao <yaohongbo@huawei.com>
Acked-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We maintain global statistics for an entire MDIO bus, as well as broken
down, per MDIO bus address statistics. Given that it is possible for
MDIO devices such as switches to access MDIO bus addresses for which
there is not a mdio_device instance created (therefore not a a
corresponding device directory in sysfs either), we also maintain
per-address statistics under the statistics folder. The layout looks
like this:

/sys/class/mdio_bus/../statistics/
	transfers
	errrors
	writes
	reads
	transfers_<addr>
	errors_<addr>
	writes_<addr>
	reads_<addr>

When a mdio_device instance is registered, a statistics/ folder is
created with the tranfers, errors, writes and reads attributes which
point to the appropriate MDIO bus statistics structure.

Statistics are 64-bit unsigned quantities and maintained through the
u64_stats_sync.h helper functions.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It seems nsim_fib6_rt_create() intent was to return
either a valid pointer or an embedded error code.

BUG: unable to handle page fault for address: fffffffffffffff4
PGD 9870067 P4D 9870067 PUD 9872067 PMD 0
Oops: 0000 [#1] PREEMPT SMP KASAN
CPU: 0 PID: 22851 Comm: syz-executor.1 Not tainted 5.5.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
RIP: 0010:jhash2 include/linux/jhash.h:125 [inline]
RIP: 0010:rhashtable_jhash2+0x76/0x2c0 lib/rhashtable.c:963
Code: b9 00 00 00 00 00 fc ff df 48 c1 e8 03 0f b6 14 08 4c 89 f0 83 e0 07 83 c0 03 38 d0 7c 08 84 d2 0f 85 30 02 00 00 49 8d 7e 04 <41> 8b 06 48 be 00 00 00 00 00 fc ff df 48 89 fa 48 c1 ea 03 0f b6
RSP: 0018:ffffc90016127190 EFLAGS: 00010246
RAX: 0000000000000007 RBX: 00000000dfb3ab49 RCX: dffffc0000000000
RDX: 0000000000000000 RSI: ffffffff839ba7c8 RDI: fffffffffffffff8
RBP: ffffc900161271c0 R08: ffff8880951f8640 R09: ffffed1015d0703d
R10: ffffed1015d0703c R11: ffff8880ae8381e3 R12: 00000000dfb3ab49
R13: 00000000dfb3ab49 R14: fffffffffffffff4 R15: 0000000000000007
FS:  00007f40bfbc6700(0000) GS:ffff8880ae800000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: fffffffffffffff4 CR3: 0000000093660000 CR4: 00000000001406f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
 rht_key_get_hash include/linux/rhashtable.h:133 [inline]
 rht_key_hashfn include/linux/rhashtable.h:159 [inline]
 rht_head_hashfn include/linux/rhashtable.h:174 [inline]
 __rhashtable_insert_fast.constprop.0+0xe15/0x1180 include/linux/rhashtable.h:723
 rhashtable_insert_fast include/linux/rhashtable.h:832 [inline]
 nsim_fib6_rt_add drivers/net/netdevsim/fib.c:603 [inline]
 nsim_fib6_rt_insert drivers/net/netdevsim/fib.c:658 [inline]
 nsim_fib6_event drivers/net/netdevsim/fib.c:719 [inline]
 nsim_fib_event drivers/net/netdevsim/fib.c:744 [inline]
 nsim_fib_event_nb+0x1b16/0x2600 drivers/net/netdevsim/fib.c:772
 notifier_call_chain+0xc2/0x230 kernel/notifier.c:83
 __atomic_notifier_call_chain+0xa6/0x1a0 kernel/notifier.c:173
 atomic_notifier_call_chain+0x2e/0x40 kernel/notifier.c:183
 call_fib_notifiers+0x173/0x2a0 net/core/fib_notifier.c:35
 call_fib6_notifiers+0x4b/0x60 net/ipv6/fib6_notifier.c:22
 call_fib6_entry_notifiers+0xfb/0x150 net/ipv6/ip6_fib.c:399
 fib6_add_rt2node net/ipv6/ip6_fib.c:1216 [inline]
 fib6_add+0x20cd/0x3ec0 net/ipv6/ip6_fib.c:1471
 __ip6_ins_rt+0x54/0x80 net/ipv6/route.c:1315
 ip6_ins_rt+0x96/0xd0 net/ipv6/route.c:1325
 __ipv6_dev_ac_inc+0x76f/0xb20 net/ipv6/anycast.c:324
 ipv6_sock_ac_join+0x4c1/0x790 net/ipv6/anycast.c:139
 do_ipv6_setsockopt.isra.0+0x3908/0x4290 net/ipv6/ipv6_sockglue.c:670
 ipv6_setsockopt+0xff/0x180 net/ipv6/ipv6_sockglue.c:944
 udpv6_setsockopt+0x68/0xb0 net/ipv6/udp.c:1564
 sock_common_setsockopt+0x94/0xd0 net/core/sock.c:3149
 __sys_setsockopt+0x261/0x4c0 net/socket.c:2130
 __do_sys_setsockopt net/socket.c:2146 [inline]
 __se_sys_setsockopt net/socket.c:2143 [inline]
 __x64_sys_setsockopt+0xbe/0x150 net/socket.c:2143
 do_syscall_64+0xfa/0x790 arch/x86/entry/common.c:294
 entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x45aff9

Fixes: 48bb9eb4 ("netdevsim: fib: Add dummy implementation for FIB offload")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Cc: Ido Schimmel <idosch@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

list_for_each_entry_rcu has built-in RCU and lock checking.
Pass cond argument to list_for_each_entry_rcu.
Signed-off-by: NMadhuparna Bhowmik <madhuparnabhowmik04@gmail.com>
Acked-by: NWei Liu <wei.liu@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Increase the number of chains and priorities to support
the whole range available in tc.

We use unmanaged tables and ignore flow level to create more
tables than what we declared to fs_core steering, and we manage
the connections between the tables themselves.

To support that we need FW with ignore_flow_level capability.
Otherwise the old behaviour will be used, where we are limited
by the number of levels we declared (4 chains, 16 prios).
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOz Shlomo <ozsh@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

To support the entire chain and prio range (32bit + 16bit),
instead of a using a static array of chains/prios of limited size, create
them dynamically, and use a rhashtable to search for existing chains/prio
combinations.

This will be used in next patch to actually increase the number using
unamanged tables support and ignore flow level capability.
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOz Shlomo <ozsh@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Before changing the chain from original chain to ft offload chain,
make sure user doesn't actually use chains.

While here, normalize the prio range to that which we support.
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

FT chain is defined as the next chain after tc.

To prepare for next patches that will increase the number of tc
chains available at runtime, use a getter function to get this
value.

The define is still used in static fs_core allocation,
to calculate the number of chains. This static allocation
will be used if the relevant capabilities won't be available
to support dynamic chains.
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Exclude the last n entries for an autogrouped flow table.

Reserving entries at the end of the FT will ensure that this FG will be
the last to be evaluated. This will be used in the next patch to create
a miss group enabling custom actions on FT miss.
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOz Shlomo <ozsh@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

If user sets ignore flow level flag on a rule, that rule can point to
a flow table of any level, including those with levels equal or less
than the level of the flow table it is added on.

This with unamanged tables will be used to create a FDB chain/prio
hierarchy much larger than currently supported level range.
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Currently, Most of the steering tree is statically declared ahead of time,
with steering prios instances allocated for each fdb chain to assign max
number of levels for each of them. This allows fs_core to manage the
connections and  levels of the flow tables hierarcy to prevent loops, but
restricts us with the number of supported chains and priorities.

Introduce unmananged flow tables, allowing the user to manage the flow
table connections. A unamanged table is detached from the fs_core flow
table hierarcy, and is only connected back to the hierarchy by explicit
FTEs forward actions.

This will be used together with firmware that supports ignoring the flow
table levels to increase the number of supported chains and prios.
Signed-off-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Reviewed-by: NOz Shlomo <ozsh@mellanox.com>
Reviewed-by: NMark Bloch <markb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This merge syncs with mlx5-next latest HW bits and layout updates for next
features, in addition one patch that improves
mlx5_create_auto_grouped_flow_table() API across all mlx5 users.

* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
  net/mlx5: Refactor mlx5_create_auto_grouped_flow_table
  net/mlx5e: Add discard counters per priority
  net/mlx5e: Expose FEC feilds and related capability bit
  net/mlx5: Add mlx5_ifc definitions for connection tracking support
  net/mlx5: Add copy header action struct layout
  net/mlx5: Expose resource dump register mapping
  net/mlx5: Add structures and defines for MIRC register
  net/mlx5: Read MCAM register groups 1 and 2
  net/mlx5: Add structures layout for new MCAM access reg groups
  net/mlx5: Expose vDPA emulation device capabilities
  net/mlx5: Add Virtio Emulation related device capabilities
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>