Use use device_property_count_u32() directly, that makes code neater.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Use use device_property_count_u32() directly, that makes code neater.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Link: https://lore.kernel.org/r/20190723191639.67883-1-andriy.shevchenko@linux.intel.comSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Samsung Exynos SoCs require to force UTMI width to 8bit, otherwise the
host side of the shared USB2 PHY doesn't work.
Reported-by: NKrzysztof Kozlowski <krzk@kernel.org>
Fixes: 707d80f0 ("usb: dwc2: gadget: Replace phyif with phy_utmi_width")
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Acked-by: NKrzysztof Kozlowski <krzk@kernel.org>
Tested-by: NKrzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Setting params.phy_utmi_width in dwc2_lowlevel_hw_init() is pointless since
it's value will be overwritten by dwc2_init_params().

This change make sure to take in account the generic PHY width information
during paraminitialisation, done in dwc2_set_param_phy_utmi_width().

By doing so, the phy_utmi_width params can still be overrided by
devicetree specific params and will also be checked against hardware
capabilities.

Fixes: 707d80f0 ("usb: dwc2: gadget: Replace phyif with phy_utmi_width")
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NJules Maselbas <jmaselbas@kalray.eu>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

If core not supported lpm, i.e. BCM2835 then confusing warnings seen
in log.

To avoid these warnings, added function dwc2_set_param_lpm() to set
lpm and other lpm related parameters based on lpm support by core.
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This patchs sets the params for the DWC2 Controller found in the
Amlogic G12A SoC family.

It mainly sets the settings reported incorrect by the driver,
leaving the remaining detected automatically by the driver and
provided by the DT node.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Disable power_down by setting the parameter to
DWC2_POWER_DOWN_PARAM_NONE. This fixes a problem on various Amlogic
Meson SoCs where USB devices are only recognized when plugged in before
booting Linux. A hot-plugged USB device was not detected even though the
device got power (my USB thumb drive for example has an LED which lit
up).

A similar fix was implemented for Rockchip SoCs in commit c216765d
("usb: dwc2: disable power_down on rockchip devices"). That commit
suggests that a change in the dwc2 driver is the cause because the
default value for the "hibernate" parameter (which then got renamed to
"power_down" to support other modes) was changed in the v4.17 merge
window with:
commit 6d23ee9c ("Merge tag 'usb-for-v4.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-testing").

Cc: <stable@vger.kernel.org> # 4.19
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Suggested-by: NChristian Hewitt <christianshewitt@gmail.com>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Power down feature of DWC2 module integrated in Samsung SoCs doesn't work
properly or needs some additional handling in PHY or SoC glue layer, so
disable it for now. Without disabling power down, DWC2 causes random memory
trashes and fails enumeration if there is no USB link to host on driver
probe.

Fixes: 03ea6d6e ("usb: dwc2: Enable power down")
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

 The bug would let the usb controller enter partial power down,
 which was formally known as hibernate, upon boot if nothing was plugged
 in to the port. Partial power down couldn't be exited properly, so any
 usb devices plugged in after boot would not be usable.

 Before the name change, params.hibernation was false by default, so
 _dwc2_hcd_suspend() would skip entering hibernation. With the
 rename, _dwc2_hcd_suspend() was changed to use  params.power_down
 to decide whether or not to enter partial power down.

 Since params.power_down is non-zero by default, it needs to be set
 to 0 for rockchip devices to restore functionality.

 This bug was reported in the linux-usb thread:
 REGRESSION: usb: dwc2: USB device not seen after boot

 The commit that caused this regression is:
6d23ee9cSigned-off-by: NSolidHal <hal@halemmerich.com>
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added ref_clk_per and sof_cnt_wkup_alert parameters in
dwc2_core_params struct and set default values.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added core parameter for service interval based scheduling.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

There's no reason to have the uframe scheduler off on dwc2.  Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".

The uframe scheduler has been off on stm32f4x9_fsotg since commit
e35b1350 ("usb: dwc2: Add support for STM32F429/439/469 USB OTG
HS/FS in FS mode (internal PHY)").  That commit is pretty recent, so
it's unclear to me why the uframe scheduler was left off.  Hopefully
it's because someone copied it from other parameters and didn't think
to try it?

Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

There's no reason to have the uframe scheduler off on dwc2.  Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".

The uframe scheduler has been off on Amlogic since commit f94310ac
("usb: dwc2: add support for Meson8b and GXBB SoCs").  While this was
after most of the recent improvements, notably the commit 9f9f09b0
("usb: dwc2: host: Totally redo the microframe scheduler"), presumably
the parameters were copied from another platform and the uframe
scheduler wasn't tried.

Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

There's no reason to have the uframe scheduler off on dwc2.  Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".

The uframe scheduler has been off on HiSilicon since commit
37dd9d65 ("usb: dwc2: add support of hi6220").  Since then there
have been many many improvements, notably the commit 9f9f09b0
("usb: dwc2: host: Totally redo the microframe scheduler")

Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Reviewed-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Tested-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

There's no reason to have the uframe scheduler off on dwc2.  Running
with uframe_sched = False is equivalent to saying "I don't want to run
the correct code, I want to run the old and incorrect code".

The uframe scheduler has been off on Broadcom since commit
58b179dc ("staging: dwc2: disable uframe_sched on the bcm2835").
Since then there have been many many improvements, notably the commit
9f9f09b0 ("usb: dwc2: host: Totally redo the microframe
scheduler")

Presumably if everyone is good w/ the uframe_sched turned back on we
can kill all the old and crufty non-uframe sched code.
Reviewed-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Tested-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added hsotg argument to dwc2_readl/writel function prototype,
and also instead of address pass offset of register.
hsotg will contain flag field for endianness.

Also customized dwc2_set_bit and dwc2_clear_bit function for
dwc2_readl/writel functions.
Signed-off-by: NGevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

When _param is unsigned and the minimum value of range is 0, it gives
the following warning:
COVERITY NO_EFFECT: This less-than-zero comparison of an unsigned value
is never true.

Converting ._param to int to avoid this warning.
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

In 4.17-rc, commit 03ea6d6e ("usb: dwc2: Enable power down")
caused the HiKey board to not correctly handle switching between
usb-gadget and usb-host mode.

Unplugging the OTG port would result in:
[   42.240973] dwc2 f72c0000.usb: dwc2_restore_host_registers: no host registers to restore
[   42.249066] dwc2 f72c0000.usb: dwc2_host_exit_hibernation: failed to restore host registers

And the USB-host ports would not function.

And plugging in the OTG port, we would see:
[   46.046557] WARNING: CPU: 3 PID: 6 at drivers/usb/dwc2/gadget.c:260 dwc2_hsotg_init_fifo+0x194/0x1a0
[   46.055761] CPU: 3 PID: 6 Comm: kworker/u16:0 Not tainted 4.17.0-rc5-00030-ge67da8c #231
[   46.055767] Hardware name: HiKey Development Board (DT)
[   46.055784] Workqueue: dwc2 dwc2_conn_id_status_change
...

Thus, this patch sets the hisi params to disable the power_down
flag by default, and gets thing working again.

Cc: John Youn <johnyoun@synopsys.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Artur Petrosyan <arturp@synopsys.com>
Cc: Grigor Tovmasyan <tovmasya@synopsys.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added descriptions for all not described parameters.
Fix all kernel doc's warnings.
Acked-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added GHWCFG4_IPG_ISOC_SUPPORTED and DCFG_IPG_ISOC_SUPPORDED
bits definitions to enable/disable IPG feature.

Added ipg_isoc_en core parameter which will indicate IPG support
enable/disable and initialize it.
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

If the dr_mode is USB_DR_MODE_OTG, forcing the mode is needed during
driver probe to get the host and device specific HW parameters. Then we
clear the force mode bits so that the core operates in OTG mode.

The force mode bits should not be touched at any other time during the
driver lifetime and they should be preserved whenever the GUSBCFG
register is written to. The force mode bit values will persist across
soft resets of the core.

If the dr_mode is either USB_DR_MODE_HOST or USB_DR_MODE_PERIPHERAL, the
force mode is set just once at probe to configure the core as either a
host or peripheral.

Given the above, we no longer need any other reset delays, force delays,
or any forced modes anywhere else in the driver. So replace all calls to
dwc2_core_reset_and_force_dr_mode() with dwc2_core_reset() and remove
all other unnecessary delays.

Also remove the dwc2_force_mode_if_needed() function since the "if
needed" part is already taken care of by the polling in
dwc2_force_mode().

Finally, remove all other calls to dwc2_clear_force_mode().
Tested-by: NStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NVardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Enable the power down option based on the core capability.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NVardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: NArtur Petrosyan <arturp@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add parameter and it's initialization, needed for hibernation.

Reimplement dwc2_set_param_power_down() to support hibernation too.
Now 'power_down' parameter can be initialized with 0, 1 or 2.
0 - No
1 - Partial power down
2 - Hibernation
Signed-off-by: NVardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

No-op change, only rename.

This code was misnamed originally. It was only responsible for partial
power down and not for hibernation.

Rename core_params->hibernation to core_params->power_down,
dwc2_set_param_hibernation() to dwc2_set_param_power_down().
Signed-off-by: NVardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add lpm, lpm_clock_gating, besl, hird_threshold_en and hird_threshold
core parameters. These will indicate LPM and LPM Errata support
as well as chosen L1 sleeping mode for the core and PHY.
Signed-off-by: NSevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Added function for supporting Active Clock Gating functionality
in the driver.

PCGCCTL1 (Power and Clock Control) register will be used
for controlling the core`s active clock gating feature, and
the previously reserved 12th bit in GHWCFG4 now indicates that the
controller supports the Dynamic Power Reduction (Active Clock Gating)
during no traffic scenarios such as L0, idle, resume and suspend
states.

dwc2_enable_acg() function sets GATEEN bit in PCGCCTL1 register
and enables ACG, if it supported.

According to ACG functional specification, enabling of ACG feature
in host mode done in host initialization, before turning Vbus on,
specifically in dwc2_core_host_init function.

Enabling of ACG feature in device mode done in device initialization,
before clearing the SftDiscon bit in DCTL.
This bit was cleared in dwc2_hsotg_core_connect() function.So
dwc2_enable_acg() called before dwc2_core_connect() calls.
Signed-off-by: NRazmik Karapetyan <razmik@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Changed AHB burst size from INCR4 to INCR by default.
With this value driver shows excellent DMA performance.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NRazmik Karapetyan <razmik@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Only check the ID portion of the GSNPSID register and don’t check
the version. This will allow the driver to work with version 4.00a
and later of the DWC_hsotg IP.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NGrigor Tovmasyan <tovmasya@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This patch fixes compatible for STM32F7 USB OTG HS and consistently rename
dw2_set_params function.
The v2 former patch [1] had been acked by Paul Young, but v1 was merged.

[1] https://patchwork.kernel.org/patch/9925573/

Fixes: d8fae8b9 ("usb: dwc2: add support for STM32F7xx USB OTG HS")
Signed-off-by: NAmelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

In host mode reading from DPTXSIZn returning invalid value in
dwc2_check_param_tx_fifo_sizes function.

In total TxFIFO size calculations unnecessarily reducing by ep_info.
hw->total_fifo_size can be fully allocated for FIFO's.

Added num_dev_in_eps member in dwc2_hw_params structure to save number
of IN EPs.

Added g_tx_fifo_size array in dwc2_hw_params structure to store power
on reset values of DPTXSIZn registers in forced device mode.

Updated dwc2_hsotg_tx_fifo_count() function to get TxFIFO count from
num_dev_in_eps.

Updated dwc2_get_dev_hwparams() function to store DPTXFSIZn in
g_tx_fifo_size array.

dwc2_get_host/dev_hwparams() functions call moved after num_dev_in_eps
set from hwcfg4.

Modified dwc2_check_param_tx_fifo_sizes() function to check TxFIFOn
sizes based on g_tx_fifo_size array.

Removed ep_info subtraction during calculation of tx_addr_max in
dwc2_hsotg_tx_fifo_total_depth() function. Also removed
dwc2_hsotg_ep_info_size() function as no more need.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGevorg Sahakyan <sahakyan@synopsys.com>
Signed-off-by: NMinas Harutyunyan <hminas@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.

Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.

This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.

Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NFelipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

For the case where an external VBUS is used, we should enable the external
VBUS comparator in the driver. This would prevent an unnecessary
overcurrent error which would then disable the host port.

This patch uses the standard 'disable-over-current' binding to allow of the
option of disabling the over-current condition.
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NDinh Nguyen <dinguyen@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This patch adds the dwc2_set_params function for STM32F7xx USB OTG HS.
Signed-off-by: NAmelie Delaunay <amelie.delaunay@st.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

USB support in the Meson8 SoCs is provided by a DWC2 controller which
works with the same settings as Meson8b and GXBB. Using the generic
"snps,dwc2" binding results in an endless stream of "Overcurrent change
detected" messages.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMartin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This patch introduces a new parameter to activate USB OTG HS/FS core
embedded phy transceiver. The STM32F4x9 SoC uses the GGPIO register
to enable the transceiver.
Also add the dwc2_set_params function for stm32f4 otg fs.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NBruno Herrera <bruherrera@gmail.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add dwc2_check_param_tx_fifo_sizes function which validates
the members of g_tx_fifo_size array and sets to average or
default values if it is needed.

Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NSevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Remove legacy DWC2_G_P_LEGACY_TX_FIFO_SIZE array for TX FIFOs.
Update dwc2_set_param_tx_fifo_sizes function to calculate
and assign default average FIFO depth to each member of
g_tx_fifo_size array. Total FIFO size, EP Info block's size,
FIFO operation mode and device operation mode are taken into
consideration during the calculation.

Cc: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: NSevak Arakelyan <sevaka@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The Hi6220's usb controller is limited in that it does not
support "Split Transactions", so it does not support communicating
with low-speed and full-speed devices behind a high-speed hub.

Thus it requires a quirk so that we can manually drop the usb
speed when low/full-speed are attached, and bump back to high
speed when they are removed.

Cc: Wei Xu <xuwei5@hisilicon.com>
Cc: Guodong Xu <guodong.xu@linaro.org>
Cc: Amit Pundir <amit.pundir@linaro.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: John Youn <johnyoun@synopsys.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Chen Yu <chenyu56@huawei.com>
Cc: Vardan Mikayelyan <mvardan@synopsys.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NChen Yu <chenyu56@huawei.com>
[jstultz: Reworked to simplify the patch, and made
 commit log to be more specific about the issue]
Signed-off-by: NJohn Stultz <john.stultz@linaro.org>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Remove debugging prints to show params.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Further reduce the set of parameters set by platforms. Many of them are
unnecessary as they should be reported by hardware. They should only
need to be overridden if there is a problem.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>