Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The siimage uses an incorrect construct to access the other drive of a pair,
causing it to access beyond an array boundary on the secondary interface.

This fixes it by using the new ide_get_paired_drive() helper instead.

Bart: patch description fixes
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* hpt34x.c: disable DMA masks for HPT345
  (hwif->autodma is zero so DMA won't be enabled anyway).

* trm290.c: disable IDE_HFLAG_TRUST_BIOS_FOR_DMA flag
  (hwif->autodma is zero so DMA won't be enabled anyway).

* Check noautodma global variable instead of drive->autodma in ide_tune_dma().

  This fixes handling of "ide=nodma" kernel parameter for icside, ide-cris,
  au1xxx-ide, pmac, it821x, jmicron, sgiioc4 and siimage host drivers.

* Remove hwif->autodma (it was not checked by IDE core code anyway) and
  drive->autodma (was set by all host drivers - except HPT345/TRM290 special
  cases - unless "ide=nodma" was used).

While at it:
- remove needless printk() from icside.c
- remove stale FIXME/comment from ide-probe.c
- don't force DMA off if PCI bus-mastering had to be enabled in setup-pci.c
  (this setting was always later over-ridden by host drivers anyway)
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

While at it:
- make struct pci_device_id tables const
- use PCI_DEVICE_ID_ITE_8213 define in it8213.c
- fix comment in generic.c
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_TRUST_BIOS_FOR_DMA host flag for host drivers that depend
  on BIOS for programming device/controller for DMA.  Set it in cy82c693,
  generic, ns87415, opti621 and trm290 host drivers.

* Add IDE_HFLAG_VDMA host flag for host drivers using VDMA.  Set it in cs5520
  host driver.

* Teach ide_tune_dma() about IDE_HFLAG_TRUST_BIOS_FOR_DMA flag.

* Add generic ide_dma_check() helper and remove all open coded ->ide_dma_check
  implementations.  Fix all places checking for presence of ->ide_dma_check
  hook to check for ->ide_dma_on instead.

* Remove no longer needed code from config_drive_for_dma().

* Make ide_tune_dma() static.

v2:
* Fix config_drive_for_dma() return values.

* Fix ide-dma.c build for CONFIG_BLK_DEV_IDEDMA_PCI=n by adding
  dummy config_drive_for_dma() inline.

* Fix IDE_HFLAG_TRUST_BIOS_FOR_DMA handling in ide_dma_check().

* Fix init_hwif_it8213() comment.

There should be no functionality changes caused by this patch.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove ide_use_fast_pio() and just re-tune PIO unconditionally if DMA tuning
has failed in ->ide_dma_check.  All host drivers using ide_use_fast_pio() set
drive->autotune so PIO is always tuned anyway and in some cases we _really_
need to re-tune PIO because PIO and DMA timings are shared.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Convert {ide_hwif_t,ide_pci_device_t}->host_flag to be u16.

* Add IDE_HFLAG_POST_SET_MODE host flag to indicate the need to program 
  the host for the transfer mode after programming the device.  Set it
  in au1xxx-ide, amd74xx, cs5530, cs5535, pdc202xx_new, sc1200, pmac
  and via82cxxx host drivers.

* Add IDE_HFLAG_NO_SET_MODE host flag to indicate the need to completely
  skip programming of host/device for the transfer mode ("smart" hosts).
  Set it in it821x host driver and check it in ide_tune_dma().

* Add ide_set_pio_mode()/ide_set_dma_mode() helpers and convert all
  direct ->set_pio_mode/->speedproc users to use these helpers.

* Move ide_config_drive_speed() calls from ->set_pio_mode/->speedproc
  methods to callers.

* Rename ->speedproc method to ->set_dma_mode, make it void and update
  all implementations accordingly.

* Update ide_set_xfer_rate() comments.

* Unexport ide_config_drive_speed().

v2:
* Fix issues noticed by Sergei:
  - export ide_set_dma_mode() instead of moving ->set_pio_mode abuse wrt
    to setting DMA modes from sc1200_set_pio_mode() to do_special()
  - check IDE_HFLAG_NO_SET_MODE in ide_tune_dma()
  - check for (hwif->set_pio_mode) == NULL in ide_set_pio_mode()
  - check for (hwif->set_dma_mode) == NULL in ide_set_dma_mode()
  - return -1 from ide_set_{pio,dma}_mode() if ->set_{pio,dma}_mode == NULL
  - don't set ->set_{pio,dma}_mode on it821x in "smart" mode
  - fix build problem in pmac.c
  - minor fixes in au1xxx-ide.c/cs5530.c/siimage.c
  - improve patch description

Changes in behavior caused by this patch:
- HDIO_SET_PIO_MODE ioctl would now return -ENOSYS for attempts to change
  PIO mode if it821x controller is in "smart" mode
- removal of two debugging printk-s (from cs5530.c and sc1200.c)
- transfer modes 0x00-0x07 passed from user space may be programmed twice on
  the device (not really an issue since 0x00 is not supported correctly by
  any host driver ATM, 0x01 is not supported at all and 0x02-0x07 are invalid)
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Use ->set_pio_mode method to program PIO modes in ide_set_xfer_rate()
(the only place which used ->speedproc to program PIO modes) and remove
handling of PIO modes from all ->speedproc implementations.

v2:
* Fix pmac_ide_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Remember to select PIO data transfer (with IORDY monitored) in sil_tune_pio()
  (->set_pio_mode method) so the controller is always programmed correctly for
  PIO transfers (this is important if DMA is not going to be used).

* Don't set DMA/UDMA timings for PIO modes in siimage_tune_chipset().

* Bump driver version.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add IDE_HFLAG_ABUSE_{PREFETCH,FAST_DEVSEL,DMA_MODES} flags
  and set them in ht6560, cmd640, cmd64x and sc1200 host drivers.

* Add set_pio_mode_abuse() for checking if host driver has a non-standard
  ->tuneproc() implementation and use it in do_special().

* Add ide_set_pio() for setting PIO mode (it uses hwif->pio_mask to find
  the maximum PIO mode supported by the host), also add ide_set_max_pio()
  wrapper for ide_set_pio() to use for auto-tuning.  Convert users of
  ->tuneproc to use ide_set{_max}_pio() where possible.  This leaves only
  do_special(), set_using_pio(), ide_hwif_restore() and ide_set_pio() as
  a direct users of ->tuneproc.

* Remove no longer needed ide_get_best_pio_mode() calls and printk-s
  reporting PIO mode selected from ->tuneproc implementations.

* Rename ->tuneproc hook to ->set_pio_mode and make 'pio' argument const.

* Remove stale comment from ide_config_drive_speed().

v2:
* Fix "ata_" prefix (Noticed by Jeff).

v3:
* Minor cleanups/fixups per Sergei's suggestions.

v4:
* Fix compile problem in drivers/ide/pci/cmd640.c
  (Noticed by Andrew Morton).

* Improve some ->set_pio_mode comments.
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_rate_filter() calls from host drivers to IDE core.

* Make ide_rate_filter() static.

* Make 'speed' argument of ->speedproc const.

v2:
* Fix it8213_tune_chipset() comment.

There should be no functionality changes caused by this patch.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ATA_PIO[0-6] defines to <linux/ata.h>.

* Add ->pio_mask field to ide_pci_device_t and ide_hwif_t.

* Add PIO masks to host drivers.

<linux/ata.h> change ACK-ed by Jeff Garzik <jeff@garzik.org>.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Drop no longer needed "PIO data" argument from ide_get_best_pio_mode()
  and convert all users accordingly.

* Remove no longer needed ide_pio_data_t.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Rename ide_pci_device_t.flags to ide_pci_device_t.host_flags
  and IDEPCI_FLAG_ISA_PORTS flag to IDE_HFLAG_ISA_PORTS.

* Add IDE_HFLAG_SINGLE flag for single channel devices.

* Convert core code and all IDE PCI drivers to use IDE_HFLAG_SINGLE
  and remove no longer needed ide_pci_device_t.channels field.

v2:
* Fix issues noticed by Sergei:
  - correct code alignment in scc_pata.c
  - s/IDE_HFLAG_SINGLE/~IDE_HFLAG_SINGLE/ in serverworks.c
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add sil_tuneproc() wrapper for siimage_tuneproc() which also sets
  PIO mode on the device.

* Add missing ide_get_best_pio_mode() call to sil_tuneproc() so
  "pio" == 255 (autotune) is handled correctly (previously PIO0 was used)
  and "pio" values > 4 && < 255 are filtered to PIO4 (instead of PIO0).

* Add code limiting maximum PIO mode according to the pair device capabilities
  to sil_tuneproc().

* Convert users of config_siimage_chipset_for_pio() to use sil_tune_pio() and
  sil_tuneproc().  This fixes PIO fallback in siimage_config_drive_for_dma() to
  use max PIO mode available instead of PIO4 (config_siimage_chipset_for_pio()
  used wrong arguments for ide_get_best_pio_mode() and as a results always
  tried to set PIO4).

* Remove no longer needed siimage_taskfile_timing()
  and config_siimage_chipset_for_pio().

* Enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
  from siimage_speedproc()

* Bump driver version.

v2:
* Fix issues noticed by Sergei:
  - correct pair device check
  - trim only taskfile PIO to the slowest of the master/slave
  - enable ->autotune unconditionally and remove PIO tuning for UDMA/MDMA modes
    from siimage_speedproc()
  - add TODO item for IORDY bugs
  - minor cleanups
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This patch allows users to override both host and device side cable detection
with "ideX=ata66" kernel parameter.  Thanks to this it should be now possible
to use UDMA > 2 modes on systems (laptops mainly) which use short 40-pin cable
instead of 80-pin one.

Next patches add automatic detection of some systems using short cables.

Changes:

* Rename hwif->udma_four to hwif->cbl and make it u8.

* Convert all existing users accordingly (use ATA_CBL_* defines while at it).  

* Add ATA_CBL_PATA40_SHORT support to ide-iops.c:eighty_ninty_three().

* Use ATA_CBL_PATA40_SHORT for "ideX=ata66" kernel parameter.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Reviewed-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>

* check ->speedproc return value in ide_tune_dma()
* use ide_tune_dma() in cmd64x/cs5530/sc1200/siimage/sl82c105/scc_pata drivers
* remove no longer needed ide_dma_enable()
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Depends on the "ide: fix UDMA/MWDMA/SWDMA masks" patch.

* add ide_hwif_t.udma_filter hook for filtering UDMA mask
  (use it in alim15x3, hpt366, siimage and serverworks drivers)
* add ide_max_dma_mode() for finding best DMA mode for the device
  (loosely based on some older libata-core.c code)
* convert ide_dma_speed() users to use ide_max_dma_mode()
* make ide_rate_filter() take "ide_drive_t *drive" as an argument instead
  of "u8 mode" and teach it to how to use UDMA mask to do filtering
* use ide_rate_filter() in hpt366 driver
* remove no longer needed ide_dma_speed() and *_ratemask()
* unexport eighty_ninty_three()

v2:
* rename ->filter_udma_mask to ->udma_filter
  [ Suggested by Sergei Shtylyov <sshtylyov@ru.mvista.com>. ]

v3:
* updated for scc_pata driver (fixes XFER_UDMA_6 filtering for user-space
  originated transfer mode change requests when 100MHz clock is used)
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NMichael Opdenacker <michael@free-electrons.com>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This driver doesn't support SWDMA so use the correct ->swdma_mask.

While at it:

* no need to call config_chipset_for_pio() in config_chipset_for_dma(),
  if DMA is not available config_chipset_for_pio() will be called
  by siimage_config_drive_for_dma() and if DMA is available
  config_siimage_chipset_for_pio() will be called by siimage_tune_chipset()

* remove needless config_chipset_for_pio() wrapper

* bump driver version
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Revised DRAC4 warning as Jeff suggested, this one includes more info
about why the problem occurs
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* add ide_set_dma() helper and make ide_hwif_t.ide_dma_check return
  -1 when DMA needs to be disabled (== need to call ->ide_dma_off_quietly)
   0 when DMA needs to be enabled  (== need to call ->ide_dma_on)
   1 when DMA setting shouldn't be changed
* fix IDE code to use ide_set_dma() instead if using ->ide_dma_check directly

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If DMA is unsupported ->ide_dma_check should disable DMA.

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

All users of ->mmio == 1 are gone so convert ->mmio into flag.

Noticed by Alan Cox.

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This results in smaller/faster/simpler code and allows future optimizations.
Also remove no longer needed ide[_mm]_{inl,outl}() and ide_hwif_t.{INL,OUTL}.

v2:
* updated for scc_pata
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* add ide_use_fast_pio() helper for use by host drivers

* add DMA capability and hwif->autodma checks to ide_use_dma()

  - au1xxx-ide/it8213/it821x drivers didn't check for (id->capability & 1)

    [ for the IT8211/2 in SMART mode this check shouldn't be made but since
      in it821x_fixups() we set DMA bit explicitly:

               if(strstr(id->model, "Integrated Technology Express")) {
                       /* In raid mode the ident block is slightly buggy
                          We need to set the bits so that the IDE layer knows
                          LBA28. LBA48 and DMA ar valid */
                       id->capability |= 3;            /* LBA28, DMA */

       we are better off using generic helper if we can ]

  - ide-cris driver didn't set ->autodma

    [ before the patch hwif->autodma was only checked in the chipset specific
      hwif->ide_dma_check implementations, for ide-cris it is cris_dma_check()
      function so there no behavior change here ]

v2:
* updated patch description (thanks to Alan Cox for the feedback)

v3:
* updated for scc_pata driver
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

In cmd64x, siimage and scc_pata drivers:
* don't set drive->init_speed as it should be already
  set by successful execution of ide_set_xfer_rate()
* use hwif->speedproc functions directly

Above changes allows removal of EXPORT_SYMBOL_GPL(ide_set_xfer_rate).

v2:
* updated for scc_pata driver
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Fix two typos found by SiI680A documentation check.  They caused the taskfile
transfer overclocking:

- in PIO mode 1 as 0x2283 must be used for both data and taskfile transfers;

- in PIO mode 2 as data and taskfile timings are swapped when writing to the
  MMIO regs.

Fix coding style and trailing whitespace in enclosing statements while at it...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

 drivers/ide/pci/siimage.c |   59 ++++++++++++++++++++++------------------------
 1 file changed, 29 insertions(+), 30 deletions(-)

also change __devinit tag for sgiioc4.c:ioc4_ide_init() to __init
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Remove dma_base2 field from ide_hwif_t as it's used only in 2 drivers and
without great need.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: John Keller <jpk@sgi.com>
Signed-off-by: NJeremy Higdon <jeremy@sgi.com>
Acked-by: NAlan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There are two changes here.  The first reverses the broken PCI_DEVICE
conversion back to the old format.  The second adds a missing PCI ID so
you can actually boot 2.6.18 on 2 month old VIA motherboards (right now
only 2.6.18-mm works).

CC'd to Jeff to check the PCI ident but its a) in several distro kernels
and b) in 2.6.18-mm [twice ??]
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NJörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

Remove all the ifdef preparation for enhanced features that never occcurred
and is only in libata.  For the SATA chips (but not yet PATA ones) politely
suggest to the user that libata may offer more features.
Signed-off-by: NAlan Cox <alan@redhat.com>
Cc: Sergei Shtylylov <sshtylyov@ru.mvista.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NJeff Garzik <jgarzik@pobox.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The siimage driver proports to support the Adaptec SA-1210 SATA
controller.  However, at least some of those cards boot-up with their
interrupts disabled internally.  The siimage driver currently ignores
that fact, so that driver does not actually work with those cards.
This patch enables those interrupts on cards that need it.

[ This is implemented based on similar code in the libata-based
  sata_sil driver. ]
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!