Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 30 8月, 2015 1 次提交
  3. 28 8月, 2015 3 次提交
    • T
      nfit: Clarify memory device state flags strings · 402bae59
      由 Toshi Kani 提交于 
      ACPI 6.0 NFIT Memory Device State Flags in Table 5-129 defines
NVDIMM status as follows.  These bits indicate multiple info,
such as failures, pending event, and capability.

  Bit [0] set to 1 to indicate that the previous SAVE to the
  Memory Device failed.
  Bit [1] set to 1 to indicate that the last RESTORE from the
  Memory Device failed.
  Bit [2] set to 1 to indicate that platform flush of data to
  Memory Device failed. As a result, the restored data content
  may be inconsistent even if SAVE and RESTORE do not indicate
  failure.
  Bit [3] set to 1 to indicate that the Memory Device is observed
  to be not armed prior to OSPM hand off. A Memory Device is
  considered armed if it is able to accept persistent writes.
  Bit [4] set to 1 to indicate that the Memory Device observed
  SMART and health events prior to OSPM handoff.

/sys/bus/nd/devices/nmemX/nfit/flags shows this flags info.
The output strings associated with the bits are "save", "restore",
"smart", etc., which can be confusing as they may be interpreted
as positive status, i.e. save succeeded.

Change also the dev_info() message in acpi_nfit_register_dimms()
to be consistent with the sysfs flags strings.
Reported-by: NRobert Elliott <elliott@hp.com>
Signed-off-by: NToshi Kani <toshi.kani@hp.com>
[ross: rename 'not_arm' to 'not_armed']
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
[djbw: defer adding bit5, HEALTH_ENABLED, for now]
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
      402bae59
    • B
      sfc: only use vadaptor stats if firmware is capable · fbe4307e
      由 Bert Kenward 提交于 
      Some of the stats handling code differs based on SR-IOV support,
and SRIOV support is only available if full-featured firmware is
used.
Do not use vadaptor stats if firmware mode is not set to
full-featured.
Signed-off-by: NShradha Shah <sshah@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      fbe4307e
    • M
      net: phy: fixed: propagate fixed link values to struct · 4b195360
      由 Madalin Bucur 提交于 
      The fixed link values parsed from the device tree are stored in
the struct fixed_phy member status. The struct phy_device members
speed, duplex were not updated.
Signed-off-by: NMadalin Bucur <madalin.bucur@freescale.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4b195360
  5. 26 8月, 2015 11 次提交
  7. 25 8月, 2015 1 次提交
    • M
      can: pcan_usb: don't provide CAN FD bittimings by non-FD adapters · 06b23f7f
      由 Marc Kleine-Budde 提交于 
      The CAN FD data bittiming constants are provided via netlink only when there
are valid CAN FD constants available in priv->data_bittiming_const.

Due to the indirection of pointer assignments in the peak_usb driver the
priv->data_bittiming_const never becomes NULL - not even for non-FD adapters.

The data_bittiming_const points to zero'ed data which leads to this result
when running 'ip -details link show can0':

35: can0: <NOARP,ECHO> mtu 16 qdisc noop state DOWN mode DEFAULT group default qlen 10
    link/can  promiscuity 0
    can state STOPPED restart-ms 0
	  pcan_usb: tseg1 1..16 tseg2 1..8 sjw 1..4 brp 1..64 brp-inc 1
	  : dtseg1 0..0 dtseg2 0..0 dsjw 1..0 dbrp 0..0 dbrp-inc 0  <== BROKEN!
	  clock 8000000

This patch changes the struct peak_usb_adapter::bittiming_const and struct
peak_usb_adapter::data_bittiming_const to pointers to fix the assignemnt
problems.

Cc: linux-stable <stable@vger.kernel.org> # >= 4.0
Reported-by: NOliver Hartkopp <socketcan@hartkopp.net>
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
      06b23f7f
  9. 24 8月, 2015 2 次提交
  11. 22 8月, 2015 1 次提交
    • M
      mm: make page pfmemalloc check more robust · 2f064f34
      由 Michal Hocko 提交于 
      Commit c48a11c7 ("netvm: propagate page->pfmemalloc to skb") added
checks for page->pfmemalloc to __skb_fill_page_desc():

        if (page->pfmemalloc && !page->mapping)
                skb->pfmemalloc = true;

It assumes page->mapping == NULL implies that page->pfmemalloc can be
trusted.  However, __delete_from_page_cache() can set set page->mapping
to NULL and leave page->index value alone.  Due to being in union, a
non-zero page->index will be interpreted as true page->pfmemalloc.

So the assumption is invalid if the networking code can see such a page.
And it seems it can.  We have encountered this with a NFS over loopback
setup when such a page is attached to a new skbuf.  There is no copying
going on in this case so the page confuses __skb_fill_page_desc which
interprets the index as pfmemalloc flag and the network stack drops
packets that have been allocated using the reserves unless they are to
be queued on sockets handling the swapping which is the case here and
that leads to hangs when the nfs client waits for a response from the
server which has been dropped and thus never arrive.

The struct page is already heavily packed so rather than finding another
hole to put it in, let's do a trick instead.  We can reuse the index
again but define it to an impossible value (-1UL).  This is the page
index so it should never see the value that large.  Replace all direct
users of page->pfmemalloc by page_is_pfmemalloc which will hide this
nastiness from unspoiled eyes.

The information will get lost if somebody wants to use page->index
obviously but that was the case before and the original code expected
that the information should be persisted somewhere else if that is
really needed (e.g.  what SLAB and SLUB do).

[akpm@linux-foundation.org: fix blooper in slub]
Fixes: c48a11c7 ("netvm: propagate page->pfmemalloc to skb")
Signed-off-by: NMichal Hocko <mhocko@suse.com>
Debugged-by: NVlastimil Babka <vbabka@suse.com>
Debugged-by: NJiri Bohac <jbohac@suse.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Acked-by: NMel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org>	[3.6+]
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      2f064f34
  13. 21 8月, 2015 3 次提交
    • D
      drm/radeon: fix hotplug race at startup · 7f98ca45
      由 Dave Airlie 提交于 
      We apparantly get a hotplug irq before we've initialised
modesetting,

[drm] Loading R100 Microcode
BUG: unable to handle kernel NULL pointer dereference at   (null)
IP: [<c125f56f>] __mutex_lock_slowpath+0x23/0x91
*pde = 00000000
Oops: 0002 [#1]
Modules linked in: radeon(+) drm_kms_helper ttm drm i2c_algo_bit backlight pcspkr psmouse evdev sr_mod input_leds led_class cdrom sg parport_pc parport floppy intel_agp intel_gtt lpc_ich acpi_cpufreq processor button mfd_core agpgart uhci_hcd ehci_hcd rng_core snd_intel8x0 snd_ac97_codec ac97_bus snd_pcm usbcore usb_common i2c_i801 i2c_core snd_timer snd soundcore thermal_sys
CPU: 0 PID: 15 Comm: kworker/0:1 Not tainted 4.2.0-rc7-00015-gbf674028 #111
Hardware name: MicroLink                               /D850MV                         , BIOS MV85010A.86A.0067.P24.0304081124 04/08/2003
Workqueue: events radeon_hotplug_work_func [radeon]
task: f6ca5900 ti: f6d3e000 task.ti: f6d3e000
EIP: 0060:[<c125f56f>] EFLAGS: 00010282 CPU: 0
EIP is at __mutex_lock_slowpath+0x23/0x91
EAX: 00000000 EBX: f5e900fc ECX: 00000000 EDX: fffffffe
ESI: f6ca5900 EDI: f5e90100 EBP: f5e90000 ESP: f6d3ff0c
 DS: 007b ES: 007b FS: 0000 GS: 0000 SS: 0068
CR0: 8005003b CR2: 00000000 CR3: 36f61000 CR4: 000006d0
Stack:
 f5e90100 00000000 c103c4c1 f6d2a5a0 f5e900fc f6df394c c125f162 f8b0faca
 f6d2a5a0 c138ca00 f6df394c f7395600 c1034741 00d40000 00000000 f6d2a5a0
 c138ca00 f6d2a5b8 c138ca10 c1034b58 00000001 f6d40000 f6ca5900 f6d0c940
Call Trace:
 [<c103c4c1>] ? dequeue_task_fair+0xa4/0xb7
 [<c125f162>] ? mutex_lock+0x9/0xa
 [<f8b0faca>] ? radeon_hotplug_work_func+0x17/0x57 [radeon]
 [<c1034741>] ? process_one_work+0xfc/0x194
 [<c1034b58>] ? worker_thread+0x18d/0x218
 [<c10349cb>] ? rescuer_thread+0x1d5/0x1d5
 [<c103742a>] ? kthread+0x7b/0x80
 [<c12601c0>] ? ret_from_kernel_thread+0x20/0x30
 [<c10373af>] ? init_completion+0x18/0x18
Code: 42 08 e8 8e a6 dd ff c3 57 56 53 83 ec 0c 8b 35 48 f7 37 c1 8b 10 4a 74 1a 89 c3 8d 78 04 8b 40 08 89 63
Reported-and-Tested-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NDave Airlie <airlied@redhat.com>
      7f98ca45
    • B
      PCI: Don't use 64-bit bus addresses on PA-RISC · 45ea2a5f
      由 Bjorn Helgaas 提交于 
      Meelis and Helge reported that 3a9ad0b4 ("PCI: Add pci_bus_addr_t")
caused HPMCs on A500 and hangs on rp5470.

PA-RISC does not set ARCH_DMA_ADDR_T_64BIT, even for 64-bit kernels, so
prior to 3a9ad0b4, we always used 32-bit PCI addresses.  After
3a9ad0b4, we do use 64-bit PCI addresses in 64-bit kernels, and
apparently there's some PA-RISC problem related to them.

Fixes: 3a9ad0b4 ("PCI: Add pci_bus_addr_t")
Link: http://lkml.kernel.org/r/alpine.LRH.2.11.1507260929000.30065@math.ut.eeReported-by: NMeelis Roos <mroos@linux.ee>
Reported-by: NHelge Deller <deller@gmx.de>
Tested-by: NHelge Deller <deller@gmx.de>
Based-on-idea-by: NYinghai Lu <yinghai@kernel.org>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NYinghai Lu <yinghai@kernel.org>
CC: stable@vger.kernel.org	# v3.19+
      45ea2a5f
    • V
      Input: gpio_keys_polled - request GPIO pin as input. · 1ae5ddb6
      由 Vincent Pelletier 提交于 
      GPIOF_IN flag was lost in:
Commit 633a21d8("input: gpio_keys_polled: Add support for GPIO
descriptors").

Without this flag, legacy code path (for non-descriptor GPIO declarations)
would configure GPIO as output (0 meaning GPIOF_DIR_OUT | GPIOF_INIT_LOW).

Cc: stable@vger.kernel.org
Signed-off-by: NVincent Pelletier <plr.vincent@gmail.com>
Reviewed-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NDmitry Torokhov <dmitry.torokhov@gmail.com>
      1ae5ddb6
  15. 20 8月, 2015 5 次提交
    • G
      clocksource/imx: Fix boot with non-DT systems · be3b0f9b
      由 Guenter Roeck 提交于 
      Commit 6dd74782 ("ARM: imx: move timer resources into a structure")
moved initialization parameters into a data structure, but neglected to set
the irq field in that data structure for non-DT boots. This causes the system
to hang if a non-DT boot is attempted.

Fixes: 6dd74782 ("ARM: imx: move timer resources into a structure")
Signed-off-by: NGuenter Roeck <linux@roeck-us.net>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: http://lkml.kernel.org/r/1440066441-13930-1-git-send-email-linux@roeck-us.netSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
      be3b0f9b
    • G
      irqchip/crossbar: Restore set_wake functionality · 8200fe43
      由 Grygorii Strashko 提交于 
      The TI crossbar irqchip doesn't provides any facility to configure the
wakeup sources, but the conversion to hierarchical irqdomains set the
irq_set_wake callback to irq_chip_set_wake_parent. The parent chip
(OMAP wakeupgen) has no irq_set_wake function either so the call will
fail with -ENOSYS. As a result the irq_set_wake() call in the resume
path will trigger an 'Unbalanced wake disable' warning.

Before the conversion the GIC irqchip was the top level irqchip and
correctly flagged with IRQCHIP_SKIP_SET_WAKE.

Restore the correct behaviour by removing the irq_set_type callback
from the crossbar irqchip and set the IRQCHIP_SKIP_SET_WAKE flag which
lets the irq_set_irq_wake() call from the driver succeed.

[ tglx: Massaged changelog ]

Fixes: 783d3186 ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-7-git-send-email-grygorii.strashko@ti.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
      8200fe43
    • G
      irqchip/crossbar: Restore the mask on suspend behaviour · 4fd8f47e
      由 Grygorii Strashko 提交于 
      The ARM GIC requires that all interrupts which are not used as a
wakeup source have to be masked during suspend.

The conversion of the crossbar irqchip to hierarchical irq domains
failed to mark the crossbar irqchip with the IRQCHIP_MASK_ON_SUSPEND
flag and therefor broke the suspend requirement of the GIC.

Before the conversion the flags were visible because the GIC was the
top level irqchip. After the conversion the crossbar irqchip is the
top level irq chip whose flags are evaluated in suspend_device_irq().
As the flag is not set the masking of the non-wakeup irqs is not
invoked which breaks suspend.

Add the IRQCHIP_MASK_ON_SUSPEND flag to the crossbar irqchip, so the
GIC interrupts get masked properly.

[ tglx: Massaged changelog ]

Fixes: 783d3186 ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-6-git-send-email-grygorii.strashko@ti.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
      4fd8f47e
    • G
      irqchip/crossbar: Restore the irq_set_type() mechanism · e269ec42
      由 Grygorii Strashko 提交于 
      The conversion of the crossbar irqchip to hierarchical irq domains
failed to provide a mechanism to properly set the trigger type of an
interrupt.

The crossbar irq chip itself has no mechanism and therefor no
irq_set_type() callback. The code before the conversion relayed the
trigger configuration directly to the underlying GIC.

Restore the correct behaviour by setting the crossbar irq_set_type
callback to irq_chip_set_type_parent(). This propagates the
set_trigger() call to the underlying GIC irqchip.

[ tglx: Massaged changelog ]

Fixes: 783d3186 ('irqchip: crossbar: Convert dra7 crossbar...')
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: <linux@arm.linux.org.uk>
Cc: <nsekhar@ti.com>
Cc: <jason@lakedaemon.net>
Cc: <balbi@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>
Cc: <tony@atomide.com>
Cc: <marc.zyngier@arm.com>
Cc: stable@vger.kernel.org # 4.1
Link: http://lkml.kernel.org/r/1439554830-19502-4-git-send-email-grygorii.strashko@ti.comSigned-off-by: NThomas Gleixner <tglx@linutronix.de>
      e269ec42
    • Y
      PCI: Tolerate hierarchies with no Root Port · b35b1df5
      由 Yijing Wang 提交于 
      We should not assume any particular hardware topology.  Commit d0751b98
("PCI: Add dev->has_secondary_link to track downstream PCIe links") relied
on the assumption that every PCIe hierarchy is rooted at a Root Port.  But
we can't rely on any assumption about what hardware we will find; we just
have to deal with the world as it is.

On some platforms, PCIe devices (endpoints, switch upstream ports, etc.)
appear directly on the root bus, and there is no Root Port in the PCI bus
hierarchy.  For example, Meelis observed these top-level devices on a
Sparc V245:

  0000:02:00.0 PCI bridge to [bus 03-0d]    Switch Upstream Port
  0001:02:00.0 PCI bridge to [bus 03]       PCIe to PCI/PCI-X Bridge

These devices *look* like they have links going upstream, but there really
are no upstream devices.

In set_pcie_port_type(), we used the parent device to figure out which side
of a switch port has a link, so if the parent device did not exist, we
dereferenced a NULL parent pointer.

Check whether the parent device exists before dereferencing it.

Meelis observed this oops on Sparc V245 and T2000.  Ben Herrenschmidt says
this is also possible on IBM PowerVM guests on PowerPC.

[bhelgaas: changelog, comment]
Link: http://lkml.kernel.org/r/alpine.LRH.2.20.1508122118210.18637@math.ut.eeReported-by: NMeelis Roos <mroos@linux.ee>
Tested-by: NMeelis Roos <mroos@linux.ee>
Signed-off-by: NYijing Wang <wangyijing@huawei.com>
Signed-off-by: NBjorn Helgaas <bhelgaas@google.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
      b35b1df5
  17. 19 8月, 2015 13 次提交