Otherwise we might not have a sensible clocking setup ready.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Make sure we update for any changes in cases where we reconfigure while
live (eg, for analogue bypass).
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Show the id we read when the id mismatch is detected.
This is useful for debugging.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Make sure we generate enough BCLKs for I2S style modes by always having
a minimum of two channels worth of clocks for the BCLK.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.

This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-

snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()

This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().

It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().

Finally, it updates the existing machine drivers that register controls to either :-

1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.

In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: NLiam Girdwood <lrg@ti.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NSusan Gao <sgao@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org

The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Otherwise we won't resync later.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

When the hardware is configured with one or both of the IN4 inputs used
for DC measurement (with no DC blocking capacitor connected) then we can
improve power consumption slightly in idle modes by applying a register
write sequence. Provide platform data to enable this, implemented using
a regmap patch.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Simple switches since there's no per-channel control.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Much more compact, both in terms of source and especially in terms of
RAM used at runtime.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We only support I2C so no need to ifdef.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

We can't just pass back the return value of snd_soc_update_bits() as it
will be 1 if a bit changed rather than zero.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

It's still useful to be able to poke around in the register map at
runtime.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

They've not been needed for a long time if they were ever required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Commit 1ee46ebd("ASoC: Make the DAI ops constant in the DAI structure")
introduced the possibility to have constant DAI ops structures, yet this is
barley used in both existing drivers and also new drivers being submitted,
although none of them modifies its DAI ops structure. The later is not
surprising since existing drivers are often used as templates for new drivers.
So this patch just constifies all existing snd_soc_dai_ops structs to eliminate
the issue altogether.

The patch was generated with the following coccinelle semantic patch:
// <smpl>
@@
identifier ops;
@@
-struct snd_soc_dai_ops ops =
+const struct snd_soc_dai_ops ops =
{ ... };
// </smpl>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Give the correct number of entries to TLV_DB_RANGE_HEAD to prevent
reading more data than actually is in the arrays.
Signed-off-by: NClemens Ladisch <clemens@ladisch.de>

Allow them to work when the device is unclocked.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This initial conversion just moves the register init, regulator acquisition
and device verification out to the I2C probe(). Movement of other parts of
the driver like the GPIO and beep generation code will follow.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Disable the thermal shutdown circuits for headphone and speaker when the
relevant outputs are not enabled in order to save current in idle modes.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

They aren't needed any more. If machines need them for other purposes then
further changes will be required.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Force MICBIAS on as well as SYSCLK as the WM8962 accessory detection can't
function without both. No point in making machine drivers manually enable
it.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Ensure everything is set up before we start detecting.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Since we have code to automatically manage the start and stop of the FLL
based on the SYSCLK widget if SYSCLK is already enabled and the FLL is
configured then we need to start it up.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Since there is no current software control for these they would otherwise
be left enabled, consuming power.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

The WM8962 has a separate software reset for the PLL registers. Ensure that
these are reset also on startup.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Also fix return values for speaker switch updates.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

Signed-off-by: NSusan Gao <sgao@opensource.wolfsonmicro.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmico.com>
Cc: stable@kernel.org

A supply widget is generally clearer than a MICBIAS widget and a mic bias
is just a type of supply so use a supply widget for the MICBIAS. This also
avoids confusion with the routing when connected to multiple inputs.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Matches the register name and avoids confusion with board widgets.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

This functionality is now subsumed within the bias management, using the
standard cache management functionality, without assuming the cache type.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Ensure that we don't spuriously trigger early.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

This should never happen with level triggered IRQs.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

The WM8962 features a DSP providing a number of signal processing
features including HD Bass and Virtual Surround Sound (VSS).  Enable
initial support for this, allowing users to enable and disable the
algorithms using the default coefficient sets.  Further patches will
add support for runtime configuration of the DSP coefficients.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>

When the clocking registers are not overriden some of the registers are
not writable.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NLiam Girdwood <lrg@ti.com>
Cc: stable@kernel.org