Support RTL8153C, RTL8153D, RTL8156A, and RTL8156B. The RTL8156A
and RTL8156B are the 2.5G ethernet.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The different chips may have different requests when changing mtu.
Therefore, add a new help function of rtl_ops to change mtu. Besides,
reset the tx/rx after changing mtu.

Additionally, add mtu_to_size() and size_to_mtu() macros to simplify
the code.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use bits operations to record and check the firmware.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set the maximum inter frame gap time (144ns) for speed 10M/half and
100M/half. It improves the performance for those speeds. And, there
is no effect for the other speeds.

For 10M/half and 100M/half, the fast inter frame gap time let the
device couldn't use the feature of the aggregation effectively,
because the transfer would be completed fastly. Therefore, use the
maximum value to improve the effect of the aggregation. However, you
may not feel the improvement for fast CPUs, because they compensate
for the effect of the aggregation.
Signed-off-by: NHayes Wang <hayeswang@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The intention is for the loop to timeout if the body does not succeed.
The current logic calls time_is_before_jiffies(timeout) which is false
until after the timeout, so the loop body never executes.

Fix by using readl_poll_timeout as a more standard and less error-prone
solution.

Fixes: ba37b7ca ("net: ethernet: mtk_eth_soc: add support for initializing the PPE")
Signed-off-by: NIlya Lipnitskiy <ilya.lipnitskiy@gmail.com>
Cc: Felix Fietkau <nbd@nbd.name>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tx queue cleanup happens in interrupt handler on same core as rx queue
processing. Both can take considerable amount of processing in high
packet-per-second scenarios.

Sending big amounts of packets can stall the rx processing which is
unfair and also can lead to out-of-memory condition since
__dev_kfree_skb_irq queues the skbs for later kfree in softirq which
is not allowed to happen with heavy load in interrupt handler.

This puts tx cleanup in its own napi and enables threaded napi to
allow the rx/tx queue processing to happen on different cores.

The ability to sustain equal amounts of tx/rx traffic increased:
from 280Kpps to 1130Kpps on Threadripper 3960X with upcoming
Mikrotik 10/25G NIC,
from 520Kpps to 850Kpps on Intel i3-3320 with Mikrotik RB44Ge adapter.
Signed-off-by: NGatis Peisenieks <gatis@mikrotik.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As explained in bugfix commit 6ab4c311 ("net: bridge: don't notify
switchdev for local FDB addresses") as well as in this discussion:
https://lore.kernel.org/netdev/20210117193009.io3nungdwuzmo5f7@skbuf/

the switchdev notifiers for FDB entries managed to have a zero-day bug,
which was that drivers would not know what to do with local FDB entries,
because they were not told that they are local. The bug fix was to
simply not notify them of those addresses.

Let us now add the 'is_local' bit to bridge FDB entries, and make all
drivers ignore these entries by their own choice.
Co-developed-by: NTobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: NTobias Waldekranz <tobias@waldekranz.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Reviewed-by: NIdo Schimmel <idosch@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report corrected bits.

v2: catch reg access errors (Saeed)
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Acked-by: NSaeed Mahameed <saeedm@nvidia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report what appears to be the standard block counts:
 - 30.5.1.1.17 aFECCorrectedBlocks
 - 30.5.1.1.18 aFECUncorrectableBlocks

Don't report the per-lane symbol counts, if those really
count symbols they are not what the standard calls for
(even if symbols seem like the most useful thing to count.)

Fingers crossed that fec_corrected_errors is not in symbols.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report corrected bits.
Signed-off-by: NJakub Kicinski <kuba@kernel.org>
Reviewed-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert system_wq queue_work() to schedule_work() which is
a wrapper around it, since the former is a rare construct.

Fixes: 7294380c ("enetc: support PTP Sync packet one-step timestamping")
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Acked-by: NJakub Kicinski <kuba@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To reduce the processing of unnecessary mailbox command when PF supports
actively push its link status to VFs, VFs stop sending request link
status command in periodic service task in this case.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, VF updates its link status every second by send query command
to PF in periodic service task. If link stats of PF is changed, VF may
need at most one second to update its link status.

To reduce delay of link status between PF and VFs, PF actively push its
link status to VFs when its link status is updated. And to let VF know
PF supports this new feature, the link status changed mailbox command
adds one bit to indicate it.
Signed-off-by: NGuangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Atheros AR8031 and AR8033 expose different registers for SGMII/Fiber
as well as the copper side of the PHY depending on the BT_BX_REG_SEL bit
in the chip configure register.

The driver assumes the copper side is selected on probe, but this might
not be the case depending which page was last selected by the
bootloader. Notably, Ubiquiti UniFi bootloaders show this behavior.

Select the copper page when probing to circumvent this.
Signed-off-by: NDavid Bauer <mail@david-bauer.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The scope of this variable can be reduced so do that.
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

We were saving the return value from ice_vsi_manage_rss_lut(), but
the errors from that function are not critical so change it to
return void and remove the code that saved the value.
Signed-off-by: NPaul M Stillwell Jr <paul.m.stillwell.jr@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Silence false errors, warnings and style issues reported by cppcheck.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Currently the vsi->vf_id is set only for ICE_VSI_VF and it's left as 0
for all other VSI types. This is confusing and could be problematic
since 0 is a valid vf_id. Fix this by always setting non VF VSI types to
ICE_INVAL_VFID.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The only time you can ever have a rq_last_status is if
a firmware event was somehow reporting a status on the receive
queue, which are generally firmware initiated events or
mailbox messages from a VF.  Mostly this struct member was unused.

Fix this problem by still printing the value of the field in a debug
print, but don't store the value forever in a struct, potentially
creating opportunities for callers to use the wrong struct member.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Do a minor refactor on ice_vsi_rebuild to use a local
variable to store vsi->type.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The driver previously printed it's PCI address in
the name field for the pci resource, which when displayed
via /proc/iomem, would print the same thing twice.

It's more useful for debugging to see the driver name, as
most other modules do.

Here's a diff of before and after this change:
     99100000-991fffff : 0000:3b:00.1
   9a000000-a04fffff : PCI Bus 0000:3b
     9a000000-9bffffff : 0000:3b:00.1
-      9a000000-9bffffff : 0000:3b:00.1
+      9a000000-9bffffff : ice
     9c000000-9dffffff : 0000:3b:00.0
-      9c000000-9dffffff : 0000:3b:00.0
+      9c000000-9dffffff : ice
     9e000000-9effffff : 0000:3b:00.1
     9f000000-9fffffff : 0000:3b:00.0
     a0000000-a000ffff : 0000:3b:00.1
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

There was an excessive increment of the QSFP page, which is
now fixed. Additionally, this new update now reads 8 bytes
at a time and will retry each request if the module/bus is
busy.

Also, prevent reading from upper pages if module does not
support those pages.
Signed-off-by: NScott W Taylor <scott.w.taylor@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Use a dedicated bitfield in order to both increase
the amount of checking around the length of ITR writes
as well as simplify the checks of dynamic mode.

Basically unpack the "high bit means dynamic" logic
into bitfields.

Also, remove some unused ITR defines.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The driver would occasionally miss that there were outstanding
descriptors to clean when exiting busy/napi poll. This issue has
been in the code since the introduction of the ice driver.

Attempt to "catch" any remaining work by triggering a software
interrupt when exiting napi poll or busy-poll. This will not
cause extra interrupts in the case of normal execution.

This issue was found when running sfnt-pingpong, with busy
poll enabled, and typically with larger I/O sizes like > 8192,
the program would occasionally report > 1 second maximums
to complete a ping pong.
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The ice driver has support for adaptive interrupt moderation, an
algorithm for tuning the interrupt rate dynamically. This algorithm
is based on various assumptions about ring size, socket buffer size,
link speed, SKB overhead, ethernet frame overhead and more.

The Linux kernel has support for a dynamic interrupt moderation
algorithm known as "dimlib". Replace the custom driver-specific
implementation of dynamic interrupt moderation with the kernel's
algorithm.

The Intel hardware has a different hardware implementation than the
originators of the dimlib code had to work with, which requires the
driver to use a slightly different set of inputs for the actual
moderation values, while getting all the advice from dimlib of
better/worse, shift left or right.

The change made for this implementation is to use a pair of values
for each of the 5 "slots" that the dimlib moderation expects, and
the driver will program those pairs when dimlib recommends a slot to
use. The currently implementation uses two tables, one for receive
and one for transmit, and the pairs of values in each slot set the
maximum delay of an interrupt and a maximum number of interrupts per
second (both expressed in microseconds).

There are two separate kinds of bugs fixed by using DIMLIB, one is
UDP single stream send was too slow, and the other is that 8K
ping-pong was going to the most aggressive moderation and has much
too high latency.

The overall result of using DIMLIB is that we meet or exceed our
performance expectations set based on the old algorithm.
Co-developed-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Introduce several new helpers for writing ITR and GLINT_RATE
registers, and refactor the code calling them.  This resulted
in removal of several duplicate functions and rolled a bunch
of simple code back into the calling routines.

In particular this removes some code that was doing both
a store and a set in a helper function, which seems better
done as separate tasks in the caller (and generally takes
less lines of code even with a tiny bit of repetition).
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Add two new VSI states, one to track if a netdev for the VSI has been
allocated and the other to track if the netdev has been registered.
Call unregister_netdev/free_netdev only when the corresponding state
bits are set.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Remove the leading underscores in enum ice_pf_state. This is not really
communicating anything and is unnecessary. No functional change.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

The well-known IANA protocol port 3260 (iscsi-target 0x0cbc) and the
ether-types 0x8906 (ETH_P_FCOE) and 0x8914 (ETH_P_FIP) are already defined
in kernel header files.  Use those definitions instead of open-coding the
same.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Tested-by: NTony Brelinski <tonyx.brelinski@intel.com>
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>

Normally, the bootloader will already initialize the MAC address
registers of the ENETC and the driver will just use them or generate a
random one, if it is not initialized.

Add a new way to provide the MAC address: via device tree. Besides the
usual 'mac-address' property, there is also the possibility to fetch it
via a NVMEM provider. The sl28 board stores the MAC address in the SPI
NOR flash OTP region. Having this will allow linux to fetch the MAC
address from there without being dependent on the bootloader.

No in-tree boards have the device tree properties set, thus for these,
this is a no-op.
Signed-off-by: NMichael Walle <michael@walle.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following coccicheck warning:

./drivers/net/ethernet/sfc/enum.h:80:7-28: duplicated argument to |
Signed-off-by: NWan Jiabing <wanjiabing@vivo.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds support for the [g|s]et_pauseparam ethtool ops. It considers
that the chip doesn't support pause frame use in jumbo mode.
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Synopsis MAC controller supports auxiliary snapshot feature that
allows user to store a snapshot of the system time based on an external
event.

This patch add supports to the above mentioned feature. Users will be
able to triggered capturing the time snapshot from user-space using
application such as testptp or any other applications that uses the
PTP_EXTTS_REQUEST ioctl request.

Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: NTan Tee Min <tee.min.tan@intel.com>
Co-developed-by: NWong Vee Khee <vee.khee.wong@linux.intel.com>
Signed-off-by: NWong Vee Khee <vee.khee.wong@linux.intel.com>
Acked-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting 10G without autonegotiation is invalid according to
phy_ethtool_ksettings_set(). Thus, we need to set it during
autonegotiation.

If 1G autonegotiation can't complete for quite a time, but there is
signal in line, switch line interface type to 10GBase-R, if supported,
in hope for link to be established.

And vice versa. If 10GBase-R link can't be established for quite a time,
and autonegotiation is enabled, and there is signal in line, switch line
interface type to appropriate 1G mode, i.e. 1000Base-X or SGMII, if
supported.
Signed-off-by: NIvan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

No functional changes, just move read link status routines below
autonegotiation configuration to make future functional changes more
distinct.
Signed-off-by: NIvan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some SFP modules uses RX_LOS for link indication. In such cases link
will be always up, even without cable connected. RX_LOS changes will
trigger link_up()/link_down() upstream operations. Thus, check that SFP
link is operational before actual read link status.

If there is no SFP cage connected to the tranciever, check only PMD
Recieve Signal Detect register.
Signed-off-by: NIvan Bornyakov <i.bornyakov@metrotek.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow to create an RQ which is not registered as an XDP RQ. For example:
the trap-RQ doesn't register as an XDP RQ.

Fixes: 869c5f92 ("net/mlx5e: Generalize open RQ")
Signed-off-by: NAya Levin <ayal@nvidia.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

There should be no spaces at the start of the line.
Signed-off-by: NWenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: NWeihang Li <liweihang@huawei.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

void function return statements are not generally useful.
Signed-off-by: NWenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: NWeihang Li <liweihang@huawei.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>

There should be a blank lines after declarations.
Signed-off-by: NWenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: NWeihang Li <liweihang@huawei.com>
Signed-off-by: NSaeed Mahameed <saeedm@nvidia.com>