Address learning should initially be turned off by the driver for port
operation in standalone mode, then the DSA core handles changes to it
via ds->ops->port_bridge_flags().

Leaving address learning enabled while ports are standalone breaks any
kind of communication which involves port B receiving what port A has
sent. Notably it breaks the ksz9477 driver used with a (non offloaded,
ports act as if standalone) bonding interface in active-backup mode,
when the ports are connected together through external switches, for
redundancy purposes.

This fixes a major design flaw in the ksz9477 and ksz8795 drivers, which
unconditionally leave address learning enabled even while ports operate
as standalone.

Fixes: b987e98e ("dsa: add DSA switch driver for Microchip KSZ9477")
Link: https://lore.kernel.org/netdev/CAFZh4h-JVWt80CrQWkFji7tZJahMfOToUJQgKS5s0_=9zzpvYQ@mail.gmail.com/Reported-by: NBrian Hutchinson <b.hutchman@gmail.com>
Signed-off-by: NVladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20220818164809.3198039-1-vladimir.oltean@nxp.comSigned-off-by: NJakub Kicinski <kuba@kernel.org>

This patch add support for phylink mac config for ksz series of
switches. All the files ksz8795, ksz9477 and lan937x uses the ksz common
xmii function. Instead of calling from the individual files, it is moved
to the ksz common phylink mac config function.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In ksz9477.c file, configuring the xmii register is performed based on
the flag NEW_XMII. The flag is reset for ksz9893 switch and set for
other switch. This patch uses the ksz common xmii set and get function.
The bit values are configured based on the chip id.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch read the rgmii tx and rx delay from device tree and stored it
in the ksz_port.  It applies the rgmii delay to the xmii tune adjust
register based on the interface selected in phylink mac config. There
are two rgmii port in LAN937x and value to be loaded in the register
vary depends on the port selected.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the common ksz_set_xmii function for ksz series switch
and update the lan937x code phylink mac config. The register address for
the ksz8795 is Port 5 Interface control 6 and for all other switch is
xMII Control 1.
The bit value for selecting the interface is same for
KSZ8795 and KSZ9893 are same. The bit values for KSZ9477 and lan973x are
same. So, this patch add the bit value for each switches in
ksz_chip_data and configure the registers based on the chip id.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add the support for common phylink mac link up for the ksz
series switch. The register address, bit position and values are
configured based on the chip id to the dev->info structure.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add common function for configuring the Full/Half duplex and
transmit/receive flow control. KSZ8795 uses the Global control register
4 for configuring the duplex and flow control, whereas all other KSZ9477
based switch uses the xMII Control 0 register.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the function for configuring the 100/10Mbps speed
selection for the ksz switches. KSZ8795 switch uses Global control 4
register 0x06 bit 4 for choosing 100/10Mpbs. Other switches uses xMII
control 1 0xN300 for it.
For KSZ8795, if the bit is set then 10Mbps is chosen and if bit is
clear then 100Mbps chosen. For all other switches it is other way
around, if the bit is set then 100Mbps is chosen.
So, this patch add the generic function for ksz switch to select the
100/10Mbps speed selection. While configuring, first it disables the
gigabit functionality and then configure the respective speed.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add helper function for setting and getting the gigabit
enable for the ksz series switch. KSZ8795 switch has different register
address compared to all other ksz switches. KSZ8795 series uses the Port
5 Interface control 6 Bit 6 for configuring the 1Gbps or 100/10Mbps
speed selection. All other switches uses the xMII control 1 0xN301
register Bit6 for gigabit.
Further, for KSZ8795 & KSZ9893 switches if bit 1 then 1Gbps is chosen
and if bit 0 then 100/10Mbps is chosen. It is other way around for
other switches bit 0 is for 1Gbps. So, this patch implements the common
function for configuring the gigabit set and get capability.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add support for phylink_mac_config dsa hook. It configures
the mac for MII/RMII modes. The RGMII mode will be added in the future
patches.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add support for phylink_mac_link_up. It configures the mac
for the speed, flow control and duplex mode.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch update the ksz_get_tag_protocol to return LAN937x specific
tag if the chip id matches one of LAN937x series switch
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ksz9477 and lan937x has few difference in the static and reserved
table register 0x041C. For the ksz9477 if the bit 0 is 1 - read
operation and 0 - write operation. But for lan937x bit 1:0 used for
selecting the read/write operation, 01 - write and 10 - read.
To use ksz9477 mdb add/del and enable_stp_addr for the lan937x, masks &
shifts are introduced for ksz9477 & lan937x in ksz_common.c. Then
updated the function with masks & shifts based on the switch instead of
hard coding it.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for pause specific stats.

Tested on ksz9477.
Signed-off-by: NOleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NJakub Kicinski <kuba@kernel.org>

This patch moves the broadcast ctrl, multicast ctrl and start control
registers from ksz_chip_dat to ksz_chip_reg.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the stp_ctrl_reg from the ksz_chip_data to ksz_chip_reg
structure.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The register size for the ksz8 switches is u8 and for ksz9477 series is
u16.  To have common struct for ksz series switches the size of reg is
increased from u8 to u16.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves ksz8->shifts from ksz8795.c to ksz_common.c. The shifts
are dereferenced using dev->info->shifts.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the ksz8->masks from ksz8795.c to ksz_common.c. The
mask will be dereferenced using dev->info->masks.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the ksz8->regs from ksz8795.c to the ksz_common.c. And
the regs is dereferrenced using dev->info->regs.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch delete the ksz8_switch_register and ksz9477_switch_register
since both are calling the ksz_switch_register function. Instead the
ksz_switch_register is called from the probe function.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch move the ksz_dev_ops from individual files to ksz_common.c.
And the dev_ops is assigned to ksz_device based on the switch detect.
This reduces the redundant function and allows to reuse the
functionality for LAN937x which has similar register set.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At present, ksz8795.c and ksz9477.c have separate dsa_switch_ops
structure initialization. This patch modifies the files such a way that
ksz switches has common dsa_switch_ops in the ksz_common.c file.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch move the setting the start bit from the individual switch
configuration to ksz_setup
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch moves the enabling the multicast storm protection from
individual setup function to ksz_setup function.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch move the 10% broadcast protection from the individual setup
to ksz_setup. In the ksz9477, broadcast protection is updated in reset
function.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch move the common initialization of switches to ksz_setup and
perform the switch specific initialization using the ksz_dev_ops
function pointer.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to transmit the STP BPDU packet to the CPU port, the STP
address 01-80-c2-00-00-00 has to be added to static alu table for
ksz8795 series switch. For the ksz9477 switch, there is reserved
multicast table which handles forwarding the particular set of
multicast address to cpu port. So enabling the multicast reserved table
and updated the cpu port index. The stp addr is enabled during the setup
phase using the enable_stp_addr pointer in struct ksz_dev_ops.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To have the common set of initialization in ksz_setup, introduced the
new config_cpu_port member to ksz_dev_ops. Since both the ksz8795.c and
ksz9477.c configuring the cpu port in the setup function, introduced the
member.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch renames the shutdown to reset in ksz_dev_ops in order to use
the reset dev_ops in the ksz_setup.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch assigns the get_phy_flags & mtu  hook of ksz8795 and ksz9477
in dsa_switch_ops to ksz_common.  For get_phy_flags hooks,checks whether
the chip is ksz8863/kss8793 then it returns error for port1.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>

This patch makes the dsa_switch_hook for fdbs to use ksz_common.c file.
And from ksz_common, individual switches fdb functions are called using
the dev->dev_ops. And removed the r_dyn_mac_table, r_sta_mac_table and
w_sta_mac_table from ksz_dev_ops as it is used only in ksz8795.c
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>

ksz_mdb_add/del in ksz_common.c is specific for the ksz8795.c file. The
ksz9477 has its separate ksz9477_port_mdb_add/del functions.  This patch
moves the ksz8795 specific mdb functionality from ksz_common to ksz8795.
And this dsa_switch_ops hooks for ksz8795/ksz9477 are invoked through
the ksz_port_mdb_add/del.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>

This patch assigns the phylink_get_caps in ksz8795 and ksz9477 to
ksz_phylink_get_caps. And update their mac_capabilities in the
respective ksz_dev_ops.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>

At present, P_STP_CTRL register value is passed as parameter to
ksz_port_stp_state from the individual dsa_switch_ops hooks. This patch
update the function to retrieve the register value through the
ksz_chip_data member.
And add the static to ksz_update_port_member since it is not called
outside the ksz_common.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>

This patch updates the common port mirror add/del dsa_switch_ops in
ksz_common.c. The individual switches implementation is executed based
on the ksz_dev_ops function pointers.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>

This patch moves the vlan dsa_switch_ops such as vlan_add, vlan_del and
vlan_filtering from the individual files ksz8795.c, ksz9477.c to
ksz_common.c file.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>

This patch move the dsa hook get_tag_protocol to ksz_common file. And
the tag_protocol is returned based on the dev->chip_id.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>

KSZ87xx and KSZ88xx have chip_id representation at reg location 0. And
KSZ9477 compatible switch and LAN937x switch have same chip_id detection
at location 0x01 and 0x02. To have the common switch detect
functionality for ksz switches, ksz_switch_detect function is
introduced.
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>

The name, regs_size and overrides members in struct ksz_device are
unused. Hence remove it.
And host_mask is used in only place of ksz8795.c file, which can be
replaced by dev->info->cpu_ports
Signed-off-by: NArun Ramadoss <arun.ramadoss@microchip.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVladimir Oltean <olteanv@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>