Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

For Alchemy 64BIT_PHYS_ADDR is already always set in arch/mips/Kconfig.
Also 64BIT_PHYS_ADDR is about to be removed.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The toolchain defines exactly one of __MIPSEB__ and
__MIPSEL__. As a result, simplify the ifdefery a little bit.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8522/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Using the __raw_{read,write}{b,w,l} functions to perform
repeatable MMIO could result in problems if the host bus
does not match the endianness of the PCI/ISA. This problem
is visible on big-endian SEAD3 configurations after commit
2925f6c0
"net: smc911x: use io{read,write}*_rep accessors". This effectively
moves away from using the __mem_* variants to __raw_* ones
and causes a kernel bug as follows:

Call Trace:
CPU 0 Unable to handle kernel paging request at virtual address 00000000,
epc == 00000000, ra == 8012b3b0
Oops[#1]:
Cpu 0
$ 0   : 00000000 00000065 00000000 00000004
$ 4   : 00000000 00000000 9a82dd60 00000000
$ 8   : 00000000 00000000 a00ae278 00000007
$12   : 0000000e 00000011 804c4228 ffff9411
$16   : 00000100 00000000 80560000 807fc6d0
$20   : 807fc8d0 807fcad0 807fbec0 00000100
$24   : 00009150 80109be0
$28   : 9a82c000 9a82dd28 00000001 8012b3b0
Hi    : 00000000
Lo    : 00000000
epc   : 00000000   (null)
    Not tainted
ra    : 8012b3b0 call_timer_fn.isra.39+0x24/0x84
Status: 10009503    KERNEL EXL IE
Cause : 00800808
BadVA : 00000000
PrId  : 00019c20 (MIPS M14Kc)
Modules linked in:
Process swapper (pid: 1, threadinfo=9a82c000, task=9a82ba18, tls=00000000)
Stack : 00000040 00000000 00000007 8056732c 80580000 00000001 9a82dd60 00200200
        80560000 8012b598 8056732c 80580000 00000001 00000000 9a82dd60 9a82dd60
        00000000 807fbd44 807fbd40 805664e0 0000000a 80800000 00000004 80125924
        0000fda0 000007f0 80000000 00000001 80800000 007f0000 00200140 80166338
        00000000 8100fda0 0000fda0 000007f0 80000000 00000001 80800000 007f0000
        ...
Call Trace:
[<8012b598>] run_timer_softirq+0x188/0x1f4
[<80125924>] __do_softirq+0xc4/0x18c
[<80166338>] handle_percpu_irq+0x54/0x84
[<80125aa4>] do_softirq+0x68/0x70
[<80103b50>] do_IRQ+0x18/0x28
[<80125d1c>] irq_exit+0x94/0xc0
[<80125aa4>] do_softirq+0x68/0x70
[<80102130>] ret_from_irq+0x0/0x4
[<80102130>] ret_from_irq+0x0/0x4
[<80125d1c>] irq_exit+0x94/0xc0
[<803165b0>] __bzero+0xd4/0x164
[<80346d0c>] mem32_serial_out+0x0/0x1c
[<8010d4ac>] free_init_pages+0x98/0xfc
[<80180a08>] free_hot_cold_page+0x2c/0x1c4
[<80180bd8>] __free_pages+0x38/0x98
[<8010d4a0>] free_init_pages+0x8c/0xfc
[<8010d4ac>] free_init_pages+0x98/0xfc
[<8049fb04>] kernel_init+0x28/0x15c
[<80147484>] schedule_tail+0x1c/0x60
[<8049fadc>] kernel_init+0x0/0x15c
[<80102178>] ret_from_kernel_thread+0x14/0x1c
[<8040a06f>] skb_pad+0xe7/0x13c
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: Steve Glendinning <steve.glendinning@shawell.net>
Cc: Ben Boeckel <mathstuf@gmail.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: Jeffrey Deans <Jeffrey.Deans@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/6672/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add myself as a maintainer for the new BMIPS target.
Signed-off-by: NKevin Cernekee <cernekee@gmail.com>
Cc: f.fainelli@gmail.com
Cc: jfraser@broadcom.com
Cc: dtor@chromium.org
Cc: tglx@linutronix.de
Cc: jason@lakedaemon.net
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8505/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Based on commit 1091458d (mmap randomization)

For 32-bit address spaces randomize within a
16MB space, for 64-bit within a 256MB space.

Test Results:
------------
Without Patch (VDSO is not randomized)
---------------------------------------
root@Maleo:~# ./aslr vdso
FAIL: ASLR not functional (vdso always at 0x7fff7000)

root@Maleo:~# ./aslr rekey vdso
pre_val==cur_val
value=0x7fff7000

With patch:(VDSO is randmoized and doesn't interfere with stack)
----------------------------------------------------------------
root@cavium-octeon2:~# ./aslr rekey vdso
pre_val!=cur_val
previous_value=0x7f830ea2
current_value=0x776e2000
root@cavium-octeon2:~# ./aslr rekey vdso
pre_val!=cur_val
previous_value=0x7fb0cea2
current_value=0x77209000
root@cavium-octeon2:~# ./aslr rekey vdso
pre_val!=cur_val
previous_value=0x7f985ea2
current_value=0x7770c000
root@cavium-octeon2:~# ./aslr rekey vdso
pre_val!=cur_val
previous_value=0x7fbc6ea2
current_value=0x7fe25000

Maps file output:
-------------------------
root@cavium-octeon2:~# ./aslr rekey maps
78584000-785a5000 rwxp 00000000 00:00 0                                  [heap]
7f9d0000-7f9f1000 rw-p 00000000 00:00 0                                  [stack]
7ffa5000-7ffa6000 r-xp 00000000 00:00 0                                  [vdso]

root@cavium-octeon2:~# ./aslr rekey maps
77de0000-77e01000 rwxp 00000000 00:00 0                                  [heap]
7f91b000-7f93c000 rw-p 00000000 00:00 0                                  [stack]
7ff99000-7ff9a000 r-xp 00000000 00:00 0                                  [vdso]

root@cavium-octeon2:~# ./aslr rekey maps
77d7f000-77da0000 rwxp 00000000 00:00 0                                  [heap]
7fc2a000-7fc4b000 rw-p 00000000 00:00 0                                  [stack]
7fe09000-7fe0a000 r-xp 00000000 00:00 0                                  [vdso]

root@cavium-octeon2:~# ./aslr rekey maps
7794c000-7794d000 r-xp 00000000 00:00 0                                  [vdso]
77e4b000-77e6c000 rwxp 00000000 00:00 0                                  [heap]
7f6e7000-7f708000 rw-p 00000000 00:00 0                                  [stack]
root@cavium-octeon2:~#
Signed-off-by: NPrem Karat <pkarat@mvista.com>
Cc: linux-mips@linux-mips.org
Cc: sergei.shtylyov@cogentembedded.com
Cc: ddaney.cavm@gmail.com
Patchwork: https://patchwork.linux-mips.org/patch/6812Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: aaro.koskinen@iki.fi
Cc: david.daney@cavium.com
Cc: linux-kernel@vger.kernel.org
Cc: markos.chandras@imgtec.com
Cc: dengcheng.zhu@imgtec.com
Cc: chenhc@lemote.com
Cc: akpm@linux-foundation.org
Patchwork: https://patchwork.linux-mips.org/patch/8535/

Signed-off-by: NMaarten ter Huurne <maarten@treewalker.org>
Cc: Apelete Seketeli <apelete@seketeli.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/7671/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8484/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix the issue with the ISA bit being lost in fixups that jump to labels
placed just before a section switch.  Such a switch leads to the ISA bit
being lost, because GAS concludes there is no code that follows and
therefore the label refers to data.  Use the `.insn' pseudo-op to
convince the tool this is not the case.

This lack of label annotation leads to microMIPS compilation errors
like:

mips-linux-gnu-ld: arch/mips/built-in.o: .fixup+0x3b8: Unsupported jump between ISA modes; consider recompiling with interlinking enabled.
mips-linux-gnu-ld: final link failed: Bad value
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: NSteven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8483/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In the microMIPS encoding some memory access instructions have their
immediate offset reduced to 12 bits only.  That does not match the GCC
`R' constraint we use in some places to satisfy the requirement,
resulting in build failures like this:

{standard input}: Assembler messages:
{standard input}:720: Error: macro used $at after ".set noat"
{standard input}:720: Warning: macro instruction expanded into multiple instructions

Fix the problem by defining a macro, `GCC_OFF12_ASM', that expands to
the right constraint depending on whether microMIPS or standard MIPS
code is produced.  Also apply the fix to where `m' is used as in the
worst case this change does nothing, e.g. where the pointer was already
in a register such as a function argument and no further offset was
requested, and in the best case it avoids an extraneous sequence of up
to two instructions to load the high 20 bits of the address in the LL/SC
loop.  This reduces the risk of lock contention that is the higher the
more instructions there are in the critical section between LL and SC.

Strictly speaking we could just bulk-replace `R' with `ZC' as the latter
constraint adjusts automatically depending on the ISA selected.
However it was only introduced with GCC 4.9 and we keep supporing older
compilers for the standard MIPS configuration, hence the slightly more
complicated approach I chose.

The choice of a zero-argument function-like rather than an object-like
macro was made so that it does not look like a function call taking the
C expression used for the constraint as an argument.  This is so as not
to confuse the reader or formatting checkers like `checkpatch.pl' and
follows previous practice.
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Signed-off-by: NSteven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8482/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Only allow 32-bit microMIPS builds, we're not ready yet for 64-bit
microMIPS support.

QEMU does have support for the 64-bit microMIPS ISA and with minor
tweaks it is possible to have a 64-bit processor emulated there that
runs microMIPS code, so despite the lack of actual 64-bit microMIPS
hardware there is a way to run 64-bit microMIPS Linux, but it can all be
considered early development and we are not there yet.  Userland tools
are lacking too, e.g. GCC produces bad code:

{standard input}: Assembler messages:
{standard input}:380: Warning: wrong size instruction in a 16-bit branch delay slot

And our build fails early on, so disable the configuration, for the sake
of automatic random config checkers if nothing else.  Whoever needs to
experiment with 64-bit microMIPS support can revert this change easily.
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8481/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix:

arch/mips/kernel/signal.c: In function 'handle_signal':
arch/mips/kernel/signal.c:533:21: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
  unsigned int tmp = (unsigned int)current->mm->context.vdso;
                     ^
arch/mips/kernel/signal.c:536:9: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
  vdso = (void *)tmp;
         ^
cc1: all warnings being treated as errors

when building a 64-bit kernel.

This is not really a supported configuration, but the cast is wrong
either way, Linux makes the assumption that sizeof(void *) equals
sizeof(unsigned long) and therefore the latter type is expected to be
used where integer operations have to be applied to pointers for some
reason.
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8480/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The microMIPS microassembler is only suitable for configurations where
the kernel itself is built to microMIPS machine code and not where only
user microMIPS software is supported.  The former is controlled with the
CPU_MICROMIPS configuration setting, whereas SYS_SUPPORTS_MICROMIPS is
used for the latter.

Not only that, but with a given microMIPS vs standard MIPS kernel
configuration only one microassembler is needed, that matches the ISA
selected -- CP0.Config3.ISAOnExc is mandatory on microMIPS processors,
so there is never a need to mix microMIPS and standard MIPS code.

Consequently build only the microassembler that matches the ISA selected
for the kernel.
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8479/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add missing microMIPS support to Malta.  Currently the kernel only
enables support for the instruction set for the SEAD-3 board despite the
fact processor features have nothing to do with the board a processor is
installed in.

In this case there is no way to run microMIPS software in a fully
supported way under Linux on QEMU.  QEMU supports the emulation of a
Malta board, but does not emulate SEAD-3.  Linux supports running
microMIPS code on a SEAD-3 board, but hardcodes such support to off on
an emulated Malta board even if the processor selected has the microMIPS
instruction set implemented.

Adding support for the SEAD-3 to QEMU is a major project.  Flipping a
bit in the kernel that shouldn't have been cleared in the first place is
a trivial effort.  Thus the answer is plain...
Signed-off-by: NMaciej W. Rozycki <macro@codesourcery.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8478/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make loongson_rtc_resources static to eliminate the following
sparse warning:
warning: symbol 'loongson_rtc_resources' was not declared. Should it be static?
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8529/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a missing include to eliminate the following sparse warnings:
warning: symbol 'prom_init' was not declared. Should it be static?
warning: symbol 'prom_free_prom_memory' was not declared. Should it be static?
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8531/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make ml2f_reboot static to elimite the following sparse warning:
warning: symbol 'ml2f_reboot' was not declared. Should it be static?
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8528/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make internal static to eliminate the following sparse warnings:
warning: symbol 'ip6_irqaction' was not declared. Should it be static?
warning: symbol 'cascade_irqaction' was not declared. Should it be static?
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8527/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a missing include to get rid of the following sparse warning:
warning: symbol 'plat_mem_setup' was not declared. Should it be static?
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8530/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a missing include to get rid of the following sparse warnings:
warning: symbol 'cs5536_pci_conf_write4' was not declared. Should it be static?
warning: symbol 'cs5536_pci_conf_read4' was not declared. Should it be static?
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8526/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Fix array initializer syntax to get rid of the following sparse warnings:
"obsolete array initializer, use C99 syntax".
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8525/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Building a 64bit kernel for the SGI O2 (IP32) and the SGI Indy (IP22) uses
the 'vmlinux.32' target, which converts the output 64-bit 'vmlinux' image
into a 32-bit wrapped image.  This is needed for certain revisions of the
IP22 and IP32 ARCS PROMs to boot correctly, but this target is missing
from the 'archhelp' info that is emitted by 'make help'.
Signed-off-by: NJoshua Kinard <kumba@gentoo.org>
Cc: Linux MIPS List <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7991/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Having #ifdefs just to guard comments is not really helpful
so drop them. Moreover, the code wasn't really reached anyway
since there is a #ifndef CONFIG_CPU_MIPSR2 on the top of the file.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8513/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Mark octeon_model_get_string() with __init and make internal functions
static.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7668/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move code to avoid forward declarations.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7667/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

We should not need to read fuses during normal operation, also the current
code has issues with that (not safe for concurrent access). Since there
are no in-kernel users for these, just delete them. Drivers should
not need such OCTEON_HAS_FEATURE mechanism in any case, instead the
information should be passed via device tree.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/7665/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Move cvmx_fuse_read_byte() into a .c file.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nsn.com>
Cc: David Daney <david.daney@cavium.com>
Cc: linux-mips@linux-mips.org
Cc: Aaro Koskinen <aaro.koskinen@nsn.com>
Patchwork: https://patchwork.linux-mips.org/patch/7666/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Continue the backtrace if we cannot find SP adjustment and RA save. In
that case, just assume the current RA. This allows us to get samples of
frequent callers of e.g. GLIBC memset().
Signed-off-by: NAaro Koskinen <aaro.koskinen@nsn.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8109/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Allow unsupported CPU types to use backtrace with timer-based profiling.
Some CPUs (notably OCTEON) lack architecture-specific oprofile driver. In
such case oprofile can fallback to timer-based mode, and arch code can
still provide the backtrace functionality. So just set up the backtrace
hook always.
Signed-off-by: NAaro Koskinen <aaro.koskinen@nsn.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8108/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

They can be useful to determine how the MMU is configured on a MC
exception.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8401/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The HTW registers can be useful to debug a MC exception.
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8400/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

printk should not be used without a KERN_ facility level
Signed-off-by: NMarkos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8399/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Parse the GIC timer frequency and interrupt from the device-tree.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8421/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add device-tree support for the MIPS GIC.  Update the GIC irqdomain's
xlate() callback to handle the three-cell specifier described in the
MIPS GIC binding document.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NJason Cooper <jason@lakedaemon.net>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8422/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The Global Interrupt Controller (GIC) present on certain MIPS systems
can be used to route external interrupts to individual VPEs and CPU
interrupt vectors.  It also supports a timer and software-generated
interrupts.
Signed-off-by: NAndrew Bresticker <abrestic@chromium.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: David Daney <ddaney.cavm@gmail.com>
Cc: Qais Yousef <qais.yousef@imgtec.com>
Cc: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/8420/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Allow loading an initrd passed by the firmware.
Signed-off-by: NAlban Bedel <albeu@free.fr>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/8354/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>