A MAC address is not necessarily a unique identifier for a netdev. Drivers
such as Linux bonds, for example, can apply the same MAC address to the
upper layer device and all lower layer devices.

NFP MAC offload for tunnel decap includes port verification for reprs but
also supports the offload of non-repr MAC addresses by assigning 'global'
indexes to these. This means that the FW will not verify the incoming port
of a packet matching this destination MAC.

Modify the MAC offload logic to assign global indexes based on MAC address
instead of net device (as it currently does). Use this to allow multiple
devices to share the same MAC. In other words, if a repr shares its MAC
address with another device then give the offloaded MAC a global index
rather than associate it with an ingress port. Track this so that changes
can be reverted as MACs stop being shared.

Implement this by removing the current list based assignment of global
indexes and replacing it with an rhashtable that maps an offloaded MAC
address to the number of devices sharing it, distributing global indexes
based on this.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP repr netdevs contain private data that can store per port information.
In certain cases, the NFP driver offloads information from non-repr ports
(e.g. tunnel ports). As the driver does not have control over non-repr
netdevs, it cannot add/track private data directly to the netdev struct.

Add infastructure to store private information on any non-repr netdev that
is offloaded at a given time. This is used in a following patch to track
offloaded MAC addresses for non-reprs and enable correct house keeping on
address changes.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for multiple memory units which are used for filter
offloads. Each filter is assigned a stats id, the MSBs of the id are
used to determine which memory unit the filter should be offloaded
to. The number of available memory units that could be used for filter
offload is obtained from HW. A simple round robin technique is used to
allocate and distribute the ids across memory units.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

QA tests report occasional timeouts on REIFY message replies. Profiling
of the two cmesg reply types under burst conditions, with a 12-core host
under heavy cpu and io load (stress --cpu 12 --io 12), show both PHY MTU
change and REIFY replies can exceed the 10ms timeout. The maximum MTU
reply wait under burst is 16ms, while the maximum REIFY wait under 40 VF
burst is 12ms. Using a 4 VF REIFY burst results in an 8ms maximum wait.
A larger VF burst does increase the delay, but not in a linear enough
way to justify a scaled REIFY delay. The worse case values between
MTU and REIFY appears close enough to justify a common timeout. Pick a
conservative 40ms to make a safer future proof common reply timeout. The
delay only effects the failure case.

Change the REIFY timeout mechanism to use wait_event_timeout() instead
of wait_event_interruptible_timeout(), to match the MTU code. In the
current implementation, theoretically, a signal could interrupt the
REIFY waiting period, with a return code of ERESTARTSYS. However, this is
caught under the general timeout error code EIO. I cannot see the benefit
of exposing the REIFY waiting period to signals with such a short delay
(40ms), while the MTU mechnism does not use the same logic. In the absence
of any reply (wakeup() call), both reply types will wake up the task after
the timeout period. The REIFY timeout applies to the entire representor
group being instantiated (e.g. VFs), while the MTU timeout apples to a
single PHY MTU change.
Signed-off-by: NFred Lotter <frederik.lotter@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, only tunnel decap rules required egdev registration for
offload in NFP. These are now supported via indirect TC block callbacks.

Remove the egdev code from NFP.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, TC block tunnel decap rules were only offloaded when a
callback was triggered through registration of the rules egress device.
This meant that the driver had no access to the ingress netdev and so
could not verify it was the same tunnel type that the rule implied.

Register tunnel devices for indirect TC block offloads in NFP, giving
access to new rules based on the ingress device rather than egress. Use
this to verify the netdev type of VXLAN and Geneve based rules and offload
the rules to HW if applicable.

Tunnel registration is done via a netdev notifier. On notifier
registration, this is triggered for already existing netdevs. This means
that NFP can register for offloads from devices that exist before it is
loaded (filter rules will be replayed from the TC core). Similarly, on
notifier unregister, a call is triggered for each currently active netdev.
This allows the driver to unregister any indirect block callbacks that may
still be active.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use driver's common notifier for LAG and tunnel configuration.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Replace the repeated license text with SDPX identifiers.
While at it bump the Copyright dates for files we touched
this year.
Signed-off-by: NEdwin Peer <edwin.peer@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NNic Viljoen <nick.viljoen@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Read the host context count symbols provided by firmware and use
it to determine the number of allocated stats ids. Previously it
won't be possible to offload more than 2^17 filter even if FW was
able to do so.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Function nfp_flower_repr_get_type_and_port expects an enum nfp_repr_type
return value but, if the repr type is unknown, returns a value of type
enum nfp_flower_cmsg_port_type.  This means that if FW encodes the port
ID in a way the driver does not understand instead of dropping the frame
driver may attribute it to a physical port (uplink) provided the port
number is less than physical port count.

Fix this and ensure a net_device of NULL is returned if the repr can not
be determined.

Fixes: 1025351a ("nfp: add flower app")
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

.ndo_get_phys_port_name was recently extended to support multi-vNIC
FWs.  These are firmwares which can have more than one vNIC per PF
without associated port (e.g. Adaptive Buffer Management FW), therefore
we need a way of distinguishing the vNICs.  Unfortunately, it's too
late to make flower use the same naming.  Flower users may depend on
.ndo_get_phys_port_name returning -EOPNOTSUPP, for example the name
udev gave the PF vNIC was just the bare PCI device-based name before
the change, and will have 'nn0' appended after.

To ensure flower's vNIC doesn't have phys_port_name attribute, add
a flag to vNIC struct and set it in flower code.  New projects will
not set the flag adhere to the naming scheme from the start.

Fixes: 51c1df83 ("nfp: assign vNIC id as phys_port_name of vNICs which are not ports")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Monitor LAG events via the NETDEV_CHANGEUPPER/NETDEV_CHANGELOWERSTATE
notifiers to maintain a list of offloadable groups. Sync these groups with
HW via a delayed workqueue to prevent excessive re-configuration. When the
workqueue is triggered it may generate multiple control messages for
different groups. These messages are linked via a batch ID and flags to
indicate a new batch and the end of a batch.

Update private data in each repr to track their LAG lower state flags. The
state of a repr is used to determine the active netdevs that can be
offloaded. For example, in active-backup mode, we only offload the netdev
currently active.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a bitmap to each flower repr to track its state if it is enslaved by a
bond. This LAG state may be different to the port state - for example, the
port may be up but LAG state may be down due to the selection in an
active/backup bond.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check if the fw contains the _abi_flower_balance_sync_enable symbol. If it
does then write a 1 to this indicating that the driver is willing to
receive NIC to kernel LAG related control messages.

If the write is successful, update the list of extra features supported by
the fw and add a stub to accept LAG cmsgs.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Don't store repr pointer to reprs array until the representor is
successfully created. This avoids message about "representor
destruction" even when it was never created. Also it cleans-up the flow.
Also, check return value after port alloc.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 29a5dcae ("nfp: flower: offload phys port MTU change") we
take encapsulation headroom into account when calculating the max allowed
MTU.  This is unnecessary as the max MTU advertised by firmware should have
already accounted for encap headroom.

Subtracting headroom twice brings the max MTU below what's necessary for
some deployments.

Fixes: 29a5dcae ("nfp: flower: offload phys port MTU change")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For very very old generation of the management FW Ethernet port
information table may theoretically not be available.  This in
turn will cause the nfp_port structures to not be allocated.

Make sure we don't crash the kernel when there is no eth_tbl:

RIP: 0010:nfp_net_pci_probe+0xf2/0xb40 [nfp]
...
Call Trace:
  nfp_pci_probe+0x6de/0xab0 [nfp]
  local_pci_probe+0x47/0xa0
  work_for_cpu_fn+0x1a/0x30
  process_one_work+0x1de/0x3e0

Found while working with broken/development version of management FW.

Fixes: a5950182 ("nfp: map mac_stats and vf_cfg BARs")
Fixes: 93da7d96 ("nfp: provide nfp_port to of nfp_net_get_mac_addr()")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a second skb list for handling control messages and limit the
number of allowed messages. Some control messages are considered more
crucial than others, resulting in the need for a second skb list. By
splitting the list into a separate high and low priority list we can
ensure that messages on the high list get added to the head of the list
that gets processed, this however has no functional impact. Previously
there was no limit on the number of messages allowed on the queue, this
could result in the queue growing boundlessly and eventually the host
running out of memory.

Fixes: b985f870 ("nfp: process control messages in workqueue in flower app")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Trigger a port mod message to request an MTU change on the NIC when any
physical port representor is assigned a new MTU value. The driver waits
10 msec for an ack that the FW has set the MTU. If no ack is received the
request is rejected and an appropriate warning flagged.

Rather than maintain an MTU queue per repr, one is maintained per app.
Because the MTU ndo is protected by the rtnl lock, there can never be
contention here. Portmod messages from the NIC are also protected by
rtnl so we first check if the portmod is an ack and, if so, handle outside
rtnl and the cmsg work queue.

Acks are detected by the marking of a bit in a portmod response. They are
then verfied by checking the port number and MTU value expected by the
app. If the expected MTU is 0 then no acks are currently expected.

Also, ensure that the packet headroom reserved by the flower firmware is
considered when accepting an MTU change on any repr.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most vNIC capabilities are netdev related.  It makes no sense
to initialize them and waste FW resources.  Some are even
counter-productive, like IRQ moderation, which will slow
down exchange of control messages.

Add to nfp_app a mask of enabled control vNIC capabilities
for apps to use.  Make flower and BPF enable all capabilities
for now.  No functional changes.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Representors are grouped in sets by type.  Currently the whole
sets are under RCU protection, but individual representor pointers
are not.  This causes some inconveniences when representors have
to be destroyed, because we have to allocate new sets to remove
any representors.  Protect the individual pointers with RCU.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PORT_REIFY message indicates whether reprs have been created or
when they are about to be destroyed. This is necessary so firmware
can know which state the driver is in, e.g. the firmware will not send
any control messages related to ports when the reprs are destroyed.

This prevents nuisance warning messages printed whenever the firmware
sends updates for non-existent reprs.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of starting up reprs assuming that there is link, only respond
to the link state reported by firmware.

Furthermore, ensure link is down after repr netdevs are created.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Extract the _abi_flower_extra_features symbol from the fw which gives a 64
bit bitmap of new features (on top of the flower base support) that the fw
can offload. Store this bitmap in the priv data associated with each app.
If the symbol does not exist, set the bitmap to 0.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Register a callback for offloading flows that have a repr as their egress
device. The new egdev_register function is added to net-next for the 4.15
release.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The criteria that reprs cannot be replaced with another new set of reprs
has been removed. This check is not needed since the only use case that
could exercise this at the moment, would be to modify the number of
SRIOV VFs without first disabling them. This case is explicitly
disallowed in any case and subsequent patches in this series
need to be able to replace the running set of reprs.

All cases where the return code used to be checked for the
nfp_app_reprs_set function have been removed.
As stated above, it is not possible for the current code to encounter a
case where reprs exist and need to be replaced.
Signed-off-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Generate a list of MAC addresses of netdevs that could be used as VXLAN
tunnel end points. Give offloaded MACs an index for storage on the NFP in
the ranges:
0x100-0x1ff physical port representors
0x200-0x2ff VF port representors
0x300-0x3ff other offloads (e.g. vxlan netdevs, ovs bridges)

Assign phys and vf indexes based on unique 8 bit values in the port num.
Maintain list of other netdevs to ensure same netdev is not offloaded
twice and each gets a unique ID without exhausting the entries. Because
the IDs are unique but constant for a netdev, any changes are implemented
by overwriting the index on NFP.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create representors after lower vNIC is registered and destroy
them before it is destroyed.  Move the code out of start/stop
callbacks directly into vnic_init/clean callbacks.  Make sure
SR-IOV callbacks don't try to create representors when lower
device does not exist.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We currently only have one app callback for vNIC creation
and destruction.  This is insufficient, because some actions
have to be taken before netdev is registered, after it's
registered and after it's unregistered.  Old callbacks
were really corresponding to alloc/free actions.  Rename
them and add proper init/clean.  Apps using representors
will be able to use new callbacks to manage lifetime of
upper devices.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify the statistics handling code by keeping pointer to vNIC's
config memory in nfp_port.  Note that this is referring to the
representor side of vNICs, vNIC side has the pointer in nfp_net.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Processing of control messages is not time-critical and future processing
of some messages will require taking the RTNL which is not possible
in a BH handler. It seems simplest to move all control message processing
to a workqueue.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The firmware expects a MAC_REPR control message when a MAC representor
is created. The driver should expect a PORTMOD message to follow which
will provide the link states of the physical port associated with the MAC
representor.
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nfp_flower_metadata_cleanup() is defined but never invoked,
not calling it will cause us to leak mask and statistics
queue memory on the host.

Fixes: 43f84b72 ("nfp: add metadata to each flow offload")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The legacy MAC address lookup doesn't work well with breakout
cables.  We are probably better off picking random addresses
than the wrong ones in the theoretical scenario where management
FW didn't tell us what the port config is.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds metadata describing the mask id of each flow and keeps track of
flows installed in hardware. Previously a flow could not be removed
from hardware as there was no way of knowing if that a specific flow
was installed. This is solved by storing the offloaded flows in a
hash table.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds a flower based TC offload handler for representor devices, this
is in addition to the bpf based offload handler. The changes in this
patch will be used in a follow-up patch to add tc flower offload to
the NFP.

The flower app enables tc offloads on representors by default.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Apps shouldn't declare their own struct net_device_ops for
representors, this makes sharing code harder.  Add necessary
nfp_app callbacks and move the definition of representors'
struct net_device_ops to common code.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Thanks to the fact that all representors will now have an nfp_port,
we can depend on information there to provide a app-independent
.ndo_get_stats64().
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

nfp_port is an abstraction which is supposed to allow us sharing
code between different netdev types (vNIC vs repr).  Spawn ports
for PFs and VFs to enable this sharing.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a cleanup callback for undoing what app init callback did.
Make flower allocate its private structure on init and free
it from the new callback.

While at it remember to set the app pointer to NULL on the
error path to avoid any races while probe path unwinds.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>