A MAC address is not necessarily a unique identifier for a netdev. Drivers
such as Linux bonds, for example, can apply the same MAC address to the
upper layer device and all lower layer devices.

NFP MAC offload for tunnel decap includes port verification for reprs but
also supports the offload of non-repr MAC addresses by assigning 'global'
indexes to these. This means that the FW will not verify the incoming port
of a packet matching this destination MAC.

Modify the MAC offload logic to assign global indexes based on MAC address
instead of net device (as it currently does). Use this to allow multiple
devices to share the same MAC. In other words, if a repr shares its MAC
address with another device then give the offloaded MAC a global index
rather than associate it with an ingress port. Track this so that changes
can be reverted as MACs stop being shared.

Implement this by removing the current list based assignment of global
indexes and replacing it with an rhashtable that maps an offloaded MAC
address to the number of devices sharing it, distributing global indexes
based on this.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible to receive a MAC address change notification without the
net device being down (e.g. when an OvS bridge is assigned the same MAC as
a port added to it). This means that an offloaded MAC address may not be
removed if its device gets a new address.

Maintain a record of the offloaded MAC addresses for each repr and netdev
assigned a MAC offload index. Use this to delete the (now expired) MAC if
a change of address event occurs. Only handle change address events if the
device is already up - if not then the netdev up event will handle it.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NFP repr netdevs contain private data that can store per port information.
In certain cases, the NFP driver offloads information from non-repr ports
(e.g. tunnel ports). As the driver does not have control over non-repr
netdevs, it cannot add/track private data directly to the netdev struct.

Add infastructure to store private information on any non-repr netdev that
is offloaded at a given time. This is used in a following patch to track
offloaded MAC addresses for non-reprs and enable correct house keeping on
address changes.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a potential tunnel end point goes down then its MAC address should
not be matchable on the NFP.

Implement a delete message for offloaded MACs and call this on net device
down. While at it, remove the actions on register and unregister netdev
events. A MAC should only be offloaded if the device is up. Note that the
netdev notifier will replay any notifications for UP devices on
registration so NFP can still offload ports that exist before the driver
is loaded. Similarly, devices need to go down before they can be
unregistered so removal of offloaded MACs is only required on down events.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Potential MAC destination addresses for tunnel end-points are offloaded to
firmware. This was done by building a list of such MACs and writing to
firmware as blocks of addresses.

Simplify this code by removing the list format and sending a new message
for each offloaded MAC.

This is in preparation for delete MAC messages. There will be one delete
flag per message so we cannot assume that this applies to all addresses
in a list.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently MAC addresses of all repr netdevs, along with selected non-NFP
controlled netdevs, are offloaded to FW as potential tunnel end-points.
However, the addresses of VF and PF reprs are meaningless outside of
internal communication and it is only those of physical port reprs
required.

Modify the MAC address offload selection code to ignore VF/PF repr devs.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent additions to the flower app private data have grouped the variables
of a given feature into a struct and added that struct to the main private
data struct.

In keeping with this, move all tunnel related private data to their own
struct. This has no affect on functionality but improves readability and
maintenance of the code.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adds support for multiple memory units which are used for filter
offloads. Each filter is assigned a stats id, the MSBs of the id are
used to determine which memory unit the filter should be offloaded
to. The number of available memory units that could be used for filter
offload is obtained from HW. A simple round robin technique is used to
allocate and distribute the ids across memory units.
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

QA tests report occasional timeouts on REIFY message replies. Profiling
of the two cmesg reply types under burst conditions, with a 12-core host
under heavy cpu and io load (stress --cpu 12 --io 12), show both PHY MTU
change and REIFY replies can exceed the 10ms timeout. The maximum MTU
reply wait under burst is 16ms, while the maximum REIFY wait under 40 VF
burst is 12ms. Using a 4 VF REIFY burst results in an 8ms maximum wait.
A larger VF burst does increase the delay, but not in a linear enough
way to justify a scaled REIFY delay. The worse case values between
MTU and REIFY appears close enough to justify a common timeout. Pick a
conservative 40ms to make a safer future proof common reply timeout. The
delay only effects the failure case.

Change the REIFY timeout mechanism to use wait_event_timeout() instead
of wait_event_interruptible_timeout(), to match the MTU code. In the
current implementation, theoretically, a signal could interrupt the
REIFY waiting period, with a return code of ERESTARTSYS. However, this is
caught under the general timeout error code EIO. I cannot see the benefit
of exposing the REIFY waiting period to signals with such a short delay
(40ms), while the MTU mechnism does not use the same logic. In the absence
of any reply (wakeup() call), both reply types will wake up the task after
the timeout period. The REIFY timeout applies to the entire representor
group being instantiated (e.g. VFs), while the MTU timeout apples to a
single PHY MTU change.
Signed-off-by: NFred Lotter <frederik.lotter@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The declaration of variable 'found' is one level too deep, fix this by
removing a tab.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are various lines that have indentation issues, fix these.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are lines that have indentation issues, fix these.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    struct boo entry[];
};

instance = kzalloc(sizeof(struct foo) + count * sizeof(struct boo), GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This issue was detected with the help of Coccinelle.
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct foo {
    int stuff;
    void *entry[];
};

instance = kzalloc(sizeof(struct foo) + sizeof(void *) * count, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL);

This issue was detected with the help of Coccinelle.
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function ice_aq_manage_mac_write takes a pointer to a MAC address.
The parameter is not marked const, even though the function doesn't need
to modify it. This prevents passing a parameter that is already marked
const. Update the function prototype to take a const pointer, to allow
passing constant pointers to this function.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds code for the detection and operation of several
additional PHY types that support higher link speeds.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the ability to offload SCTP checksum calculations to the
NIC.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use ethtool_op_get_ts_info to provide software timestamping.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch includes the following ethtool operations:

1. get_coalesce
2. set_coalesce
3. get_per_q_coalesce
4. set_per_q_coalesce

Each ITR value (current_itr/target_itr) are stored on a per
ice_ring_container basis. This is because each valid ice_ring_container
can have 1 or more rings that are tied to the same q_vector ITR index.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the driver does not support adaptive/dynamic interrupt
moderation. This patch adds support for this. Also, adaptive/dynamic
interrupt moderation is turned on by default upon driver load.

In order to support adaptive interrupt moderation, two functions were
added, ice_update_itr() and ice_itr_divisor(). These are used to
determine the current packet load and to determine a divisor based
on link speed respectively.

This patch also adds the ICE_ITR_GRAN_S define that is used in the
hot-path when setting a new ITR value. The shift is used to pet two
birds with one hand, set the ITR value while re-enabling the
interrupt. Also, the ICE_ITR_GRAN_S is defined as 1 because the device
has a ITR granularity of 2usecs.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The aggregator list needs to be preserved for use after a reset. This
patch moves it out of the port_info instance and into the ice_hw instance.
Signed-off-by: NTarun Singh <tarun.k.singh@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reworks the queue management code to allow for reuse with the
XDP feature (to be added in a future patch).
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add new infrastructure for implementing ethtool private flags using the
existing pf->flags bitmap to store them, and add the link-down-on-close
ethtool private flag to optionally bring down the PHY link when the
interface is administratively downed.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a netdev is set up/down we need to set the phsyical link state
accordingly. This patch adds that functionality by calling
ice_force_phys_link_state(vsi, link_up) in both the ice_stop() and
ice_open() paths.

In order to force link, ice_force_phys_link_state(vsi, link_up) will
first determine the current phy capabilities. If link has not changed
there is nothing to do. If link has changed, previous PHY capabilities
are saved and the "Enable Automatic Link Update" and "Link Establishment
State Machine (LESM)" enable bits are set. Then the new PHY config is
saved. The "Enable Automatic Link Update" will force the FW to execute
Setup link and restart auto-negotiation. This *should* then result in a
"Link Status Event (LSE)" which will cause the driver to get the current
link status.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add support for get_eeprom and get_eeprom_len ethtool ops

Specification states that PF software accesses NVM (shadow-ram) via AQ
commands (e.g. NVM Read, NVM Write) in the range 0x000000-0x00FFFF (64KB),
so the get_eeprom_len op should return 64KB.  If additional regions of the
16MB NVM must be read, another access method must be used.

The ethtool kernel code, by default, will ask for multiple page-size hunks
of the NVM not to exceed the value returned by ice_get_eeprom_len().
ice_read_sr_buf() deals with arch page sizes different than 4KB.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add led blinking handler to ethtool. Since led blinking is
controlled by FW/HW only ETHTOOL_ID_ACTIVE and ETHTOOL_ID_INACTIVE
are really needed.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch configures the RSS lookup table and hash key post reset.
Signed-off-by: NMd Fahad Iqbal Polash <md.fahad.iqbal.polash@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The following functions were refactored to call a new common function,
ice_aqc_send_sched_elem_cmd():

- ice_aq_add_sched_elems()
- ice_aq_delete_sched_elems()
- ice_aq_move_sched_elems()
- ice_aq_query_sched_elems()
- ice_aq_cfg_sched_elems()
- ice_aq_suspend_sched_elems()
- ice_aq_resume_sched_elems()
Signed-off-by: NGreg Priest <greg.priest@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 2fd527b7 ("net: ndo_bridge_setlink: Add extack") added a new
parameter "extack" to ice_bridge_setlink but this parameter isn't used
by the function. This results in a warning: unused parameter ‘extack’
[-Wunused-parameter]. Fix that by adding an "__always_unused" qualifier.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When allocating memory pages for context memory, if the last page table
should be fully populated, the current code will set nr_pages to 0 when
calling bnxt_alloc_ctx_mem_blk().  This will cause the last page table
to be completely blank and causing some RDMA failures.

Fix it by setting the last page table's nr_pages to the remainder only
if it is non-zero.

Fixes: 08fe9d18 ("bnxt_en: Add Level 2 context memory paging support.")
Reported-by: NEric Davis <eric.davis@broadcom.com>
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In bnxt_hwrm_check_pf_rings(), add the proper flag to test the NQ
resources.  Without the proper flag, the firmware will change
the NQ resource allocation and remap the IRQ, causing missing
IRQs.  This issue shows up when adding MQPRIO TX queues, for example.

Fixes: 36d65be9 ("bnxt_en: Disable MSIX before re-reserving NQs/CMPL rings.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, TX is given a budget which is consumed by stmmac_tx_clean()
and stmmac_rx() is given the remaining non-consumed budget.

This is wrong and in case we are sending a large number of packets this
can starve RX because remaining budget will be low.

Let's give always the same budget for RX and TX clean.

While at it, check if we missed any interrupts while we were in NAPI
callback by looking at DMA interrupt status.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RX Watchdog can be disabled by platform definitions but currently we are
initializing the descriptors before checking if Watchdog must be
disabled or not.

Fix this by checking earlier if user wants Watchdog disabled or not.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check if CBS is currently supported before trying to configure it in HW.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In DMA interrupt handler we were clearing all interrupts status, even
the ones that were not active. Fix this and only clear the active
interrupts.

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit b7d0f08e, the enable / disable of PCI device is not
managed which will result in IO regions not being automatically unmapped.
As regions continue mapped it is currently not possible to remove and
then probe again the PCI module of stmmac.

Fix this by manually unmapping regions on remove callback.

Changes from v1:
- Fix build error

Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Fixes: b7d0f08e ("net: stmmac: Fix WoL for PCI-based setups")
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

linux 5.0-rc1 shows following warning on bpi-r2/mt7623 bootup:

[ 5.170597] WARNING: CPU: 3 PID: 1 at drivers/net/phy/phy.c:548 phy_start_aneg+0x110/0x144
[ 5.178826] called from state READY
....
[ 5.264111] [<c0629fd4>] (phy_start_aneg) from [<c0e3e720>] (mtk_init+0x414/0x47c)
[ 5.271630] r7:df5f5eec r6:c0f08c48 r5:00000000 r4:dea67800
[ 5.277256] [<c0e3e30c>] (mtk_init) from [<c07dabbc>] (register_netdevice+0x98/0x51c)
[ 5.285035] r8:00000000 r7:00000000 r6:c0f97080 r5:c0f08c48 r4:dea67800
[ 5.291693] [<c07dab24>] (register_netdevice) from [<c07db06c>] (register_netdev+0x2c/0x44)
[ 5.299989] r8:00000000 r7:dea2e608 r6:deacea00 r5:dea2e604 r4:dea67800
[ 5.306646] [<c07db040>] (register_netdev) from [<c06326d8>] (mtk_probe+0x668/0x7ac)
[ 5.314336] r5:dea2e604 r4:dea2e040
[ 5.317890] [<c0632070>] (mtk_probe) from [<c05a78fc>] (platform_drv_probe+0x58/0xa8)
[ 5.325670] r10:c0f86bac r9:00000000 r8:c0fbe578 r7:00000000 r6:c0f86bac r5:00000000
[ 5.333445] r4:deacea10
[ 5.335963] [<c05a78a4>] (platform_drv_probe) from [<c05a5248>] (really_probe+0x2d8/0x424)

maybe other boards using this generic driver are affected

v2:
optimization:

- phy_set_max_speed() is only needed if you want to reduce the
  max speed, typically if the PHY supports 1Gbps but the MAC
  supports 100Mbps only.

- The pause parameters are autonegotiated. Except you have a specific
  need you normally don't need to manually fiddle with this.

- phy_start_aneg() is called implicitly by the phylib state machine,
  you shouldn't call it manually except you have a good excuse.

- netif_carrier_on/netif_carrier_off in mtk_phy_link_adjust() isn't
  needed. It's done by phy_link_change() in phylib.
Signed-off-by: NFrank Wunderlich <frank-w@public-files.de>
Reviewed-by: NHeiner Kallweit <hkallweit1@gmail.com>
Acked-by: NSean Wang <sean.wang@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 6390 copper ports have an errata which require poking magic values
into undocumented magic registers and then performing a software
reset.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A network device stack with multiple layers of bonding devices can
trigger a false positive lockdep warning. Adding lockdep nest levels
fixes this. Update the level on both enslave and unlink, to avoid the
following series of events ..

    ip netns add test
    ip netns exec test bash
    ip link set dev lo addr 00:11:22:33:44:55
    ip link set dev lo down

    ip link add dev bond1 type bond
    ip link add dev bond2 type bond

    ip link set dev lo master bond1
    ip link set dev bond1 master bond2

    ip link set dev bond1 nomaster
    ip link set dev bond2 master bond1

.. from still generating a splat:

    [  193.652127] ======================================================
    [  193.658231] WARNING: possible circular locking dependency detected
    [  193.664350] 4.20.0 #8 Not tainted
    [  193.668310] ------------------------------------------------------
    [  193.674417] ip/15577 is trying to acquire lock:
    [  193.678897] 00000000a40e3b69 (&(&bond->stats_lock)->rlock#3/3){+.+.}, at: bond_get_stats+0x58/0x290
    [  193.687851]
    	       but task is already holding lock:
    [  193.693625] 00000000807b9d9f (&(&bond->stats_lock)->rlock#2/2){+.+.}, at: bond_get_stats+0x58/0x290

    [..]

    [  193.851092]        lock_acquire+0xa7/0x190
    [  193.855138]        _raw_spin_lock_nested+0x2d/0x40
    [  193.859878]        bond_get_stats+0x58/0x290
    [  193.864093]        dev_get_stats+0x5a/0xc0
    [  193.868140]        bond_get_stats+0x105/0x290
    [  193.872444]        dev_get_stats+0x5a/0xc0
    [  193.876493]        rtnl_fill_stats+0x40/0x130
    [  193.880797]        rtnl_fill_ifinfo+0x6c5/0xdc0
    [  193.885271]        rtmsg_ifinfo_build_skb+0x86/0xe0
    [  193.890091]        rtnetlink_event+0x5b/0xa0
    [  193.894320]        raw_notifier_call_chain+0x43/0x60
    [  193.899225]        netdev_change_features+0x50/0xa0
    [  193.904044]        bond_compute_features.isra.46+0x1ab/0x270
    [  193.909640]        bond_enslave+0x141d/0x15b0
    [  193.913946]        do_set_master+0x89/0xa0
    [  193.918016]        do_setlink+0x37c/0xda0
    [  193.921980]        __rtnl_newlink+0x499/0x890
    [  193.926281]        rtnl_newlink+0x48/0x70
    [  193.930238]        rtnetlink_rcv_msg+0x171/0x4b0
    [  193.934801]        netlink_rcv_skb+0xd1/0x110
    [  193.939103]        rtnetlink_rcv+0x15/0x20
    [  193.943151]        netlink_unicast+0x3b5/0x520
    [  193.947544]        netlink_sendmsg+0x2fd/0x3f0
    [  193.951942]        sock_sendmsg+0x38/0x50
    [  193.955899]        ___sys_sendmsg+0x2ba/0x2d0
    [  193.960205]        __x64_sys_sendmsg+0xad/0x100
    [  193.964687]        do_syscall_64+0x5a/0x460
    [  193.968823]        entry_SYSCALL_64_after_hwframe+0x49/0xbe

Fixes: 7e2556e4 ("bonding: avoid lockdep confusion in bond_get_stats()")
Reported-by: Nsyzbot <syzkaller@googlegroups.com>
Signed-off-by: NWillem de Bruijn <willemb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are some lines that have indentation issues, fix these.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>