This patch add the dt node for the syscon register present on the
Allwinner A83T
Signed-off-by: NCorentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A83T has 1 pingroup with 13 pins belonging to the R_PIO
or special pin controller.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>

Allwinner V3s SoC features a "Display Engine 2.0" with only one mixer
and only one TCON connected to this mixer, which have RGB LCD output.

Add device nodes for this display pipeline.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add SoC specific compatibles for all sunXi crypto nodes, in addition to
the one already used (allwinner,sun4i-a10-crypto).
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add a node for the cryptographic engine that can be found on sun5i SoCs.
This cryptographic engine is compatible with the Allwinner cryptographic
accelerator driver.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A83T's PRCM has the same set of clocks and resets as the A64.
However, a few dividers are different. And due to the lack of a low
speed 32.768 kHz oscillator, a few of the clock parents are different.

The PRCM also has controls for various power domains. These are not
supported yet, neither in software nor in the device tree binding.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

NanoPi M1 Plus is designed and developed by FriendlyElec
for professionals, enterprise users, makers and hobbyists
using the Allwinner H3 SOC.

NanoPi M1 Plus key features
- Allwinner H3, Quad-core Cortex-A7@1.2GHz
- 1GB DDR3 RAM
- 8GB eMMC
- microSD slot
- 10/100/1000M Ethernet
- Serial Debug Port
- 5V 2A DC power-supply
Signed-off-by: NJagan Teki <jagan@amarulasolutions.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Add node for SPI NOR flash on orange-pi-zero board. Disable this node
by default and leave it to users to enable it if their board has
SPI NOR flash chip populated.

SPI NOR flash was optional in the first production batch in Dec 2016.
In later batches flash chip was pre-populated. However there should
be quite a few boards around which do not have flash chip.
Signed-off-by: NSergey Matyukevich <geomatsi@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The USB PHY can use either a GPIO pin or the PMIC's USB power supply
to sense VBUS. Since both options are available on the Cubietruck,
add the missing property for the USB power supply to the USB PHY node.

The device tree provides all usable options. Ultimately, which method
is used is up to the driver implementation.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The ACIN pins of the AXP221 PMIC on the A31 Hummingbird are tied to the
DC jack on the board through a 12V to 5V buck converter.

Enable the ACIN power supply.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The ACIN pins of the AXP209 PMIC on the Cubieboard are tied to the
DC jack on the board.

Enable the ACIN power supply.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The ACIN pins of the AXP209 PMIC on the Bananapi M1 Plus are tied to the
"power input" micro USB connector next to the SATA connector on the board.

Enable the ACIN power supply.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The ACIN pins of the AXP209 PMIC on the Cubieboard 2 are tied to the
DC jack on the board.

Enable the ACIN power supply.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

We want to keep node references in alphabetical order, except for
instances where node must be #included first.

Move the usb_otg node reference so that all references to non-AXP209
device nodes are in alphabetical order.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Cubietruck Plus has an optical SPDIF out connector.
Enable SPDIF audio output for this board.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Cubietruck Plus has 4 LEDs in different colors.
Add device nodes for them.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A83T SoC has an SPDIF transmitter block. According to the vendor
BSP kernel, it is compatible with the one found on the H3 SoC.

Add a device node and pinmux setting for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A83T SoC has a DMA controller that supports 8 DMA channels
to and from various peripherals.

Add a device node for it.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

"bcrmf" is a typo and "wifi" is the preferred form to describe
such node, so change it accordingly.
Reported-by: NAndreas Färber <afaerber@suse.de>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The datasheets for Allwinner SoCs set strict requirements on the
stability of the external crystal oscillators. Add the accuracy
for the main 24MHz oscillator to the device tree.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Now that we have support for the A83T CCU, add a device node for it,
and replace any existing placeholder clock phandles with the correct
ones.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The A10s Olinuxino has an HDMI connector. Make sure we can use it.
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

The A10s has an HDMI controller connected to the second TCON channel. Add
it to our DT.

Since the TV Encoder was the only channel 1 user so far, also add the
property now that we have several users.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
[wens@csie.org: Replaced CLK_PLL_VIDEO[01]_2X with raw numbers for now
Signed-off-by: NChen-Yu Tsai <wens@csie.org>

Allwinner V3s SoC has a SPI controller, muxed with the MMC2 controller
at PC bank. The controller itself is identical to the one in H3 SoC.

Add device tree node and the only pinmux node for it.

Tested with a Winbond W25Q128FV SPI NOR soldered on the Lichee Pi
early sample.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Lichee Pi Zero board has a "dock board" which needs to be soldered
with the 1.27mm stamp holes on a Lichee Pi Zero board.

It features:
- Onboard MIC and headphone jack (not supported yet)
- Ethernet port (not supported yet)
- An extra MicroSD slot connected to MMC1 controller
- four keys connected to the LRADC.

As it needs to be soldered with the main board to use, add a stand-alone
device tree for it.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The dock board of Lichee Pi Zero features a MicroSD slot on MMC1, which
can be used with a MicroSD card or the MicroSD-slot Wi-Fi card provided
by Lichee Pi Zero.

Add pinmux for the mmc1 controller, and specify it in the mmc1 device
node as it's the only pinmux for mmc1.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Allwinner V3s features a LRADC like the ones in older SoCs.

Add a device tree node for it.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

All the used CCU definitions are stripped from the V3s DTSI file when
it's merged, as the DTSI file and the CCU device tree binding headers
went to different trees.

As they're all in Linus's tree now, restore the usage of the
definitions.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

This names the GPIO lines on the Banana Pi board in accordance with
the A20_Banana_Pi v1.4 Specification.

This will make these line names reflect through to user space
so that they can easily be identified and used with the new
character device ABI.
Signed-off-by: NOleksij Rempel <linux@rempel-privat.de>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Orange Pi 2 routes the LINEOUT pins through a SGM8900 PA which
needs to be enabled. The onboard microphone is routed to MIC1, with
MBIAS providing power.
Signed-off-by: NMarcus Cooper <codekipper@gmail.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

We should use hyphens and not underscores in device node names.

Replace the ones that were just added.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Kbuild now complains about leading zeroes in the address portion of
device node names.

Get rid of them all, except for the uart device node. U-boot currently
hard codes the device node path. We can remove the leading zero for
the uart once we teach U-boot to use the aliases or stdout-path
property.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

tcon0 contains a muxing register used to mux tcon output to downstream
hdmi or mipi dsi encoders. tcon0 must be available for the mux to be
configured.

Whether the display subsystem is enabled or not is now solely controlled
by the display-engine node.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Allwinner A31/A31s SoCs have 2 display pipelines, as in 2 display
frontends, backends, and tcons each. The relationship between the
backends and tcons are 1:1, but the frontends can feed either backend.

Add device nodes and of graph nodes describing this relationship.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The NextThing Co. CHIP has an AXP209 PMIC with battery connector.

This enables the battery power supply subnode.
Signed-off-by: NQuentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Sinlinx SinA33 has an AXP223 PMIC and a battery connector, thus, we
enable the battery power supply subnode in its Device Tree.
Signed-off-by: NQuentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The X-Powers AXP22X PMIC exposes battery supply various data such as
the battery status (charging, discharging, full, dead), current max
limit, current current, battery capacity (in percentage), voltage max
limit, current voltage, and battery capacity (in Ah).

This adds the battery power supply subnode for AXP22X PMIC.
Signed-off-by: NQuentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The X-Powers AXP209 PMIC exposes battery supply various data such as
the battery status (charging, discharging, full, dead), current max
limit, current current, battery capacity (in percentage), voltage max
and min limits, current voltage, and battery capacity (in Ah).

This adds the battery power supply subnode for AXP20X PMIC.
Signed-off-by: NQuentin Schulz <quentin.schulz@free-electrons.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

Compiling the DT file with W=1, DTC warns like follows:

Warning (unit_address_vs_reg): Node /opp_table0/opp@1000000000 has a
unit name, but no reg property

Fix this by replacing '@' with '-' as the OPP nodes will never have a
"reg" property.
Reported-by: NKrzysztof Kozlowski <krzk@kernel.org>
Reported-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>

The Bananapi M2 Plus has a USB OTG port that can be used in both
powered host mode and peripheral mode. When in peripheral mode,
the port does not power the board. There is no VBUS sensing on
the port.

This patch adds the regulator controlling VBUS on the OTG port,
the GPIO for the ID detect pin, and enables the USB OTG and host
controllers.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>