platform_get_irq() can fail here and we must check its return value.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It had an U+FFFD: not a corrupted character but a literal well-formed
replacement marker.
Signed-off-by: NAdam Borowski <kilobyte@angband.pl>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

This error message can go because a) currently nothing else than
EPROBE_DEFER is returned and b) if this is going to change a much more
detailed error message should come from mmc_regulator_get_supply()
anyhow.
Signed-off-by: NWolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

We might be into some troubles if the bootloader misconfigured the MMC
controller.

We currently only de-assert the reset line at probe time, which means that
if the device was already out of reset, we're going to keep whatever state
was set already.

Switch to a reset instead of the deassert to have a device in a pristine
state when we start operating.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sunxi_mmc_clk_set_phase expects the actual card clock rate to be passed
to it. When the internal divider code was reworked in change ("mmc: sunxi:
Support MMC DDR52 transfer mode with new timing mode"), this requirement
was missed, and the module clock rate was passed in instead. This broke 8
bit DDR MMC on old controllers, as the module clock rate is double the
card clock rate, for which we have no valid delay settings.

Fix this by applying the internal divider to the clock rate right after
we configure it in hardware.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The A83T MMC support code introduces the timings mode switch, however
such a switch doesn't exist on new SoCs with only new timings mode.

Only execute the switch if the SoC really have the timings mode switch,
to fix the regression shown on new timings mode only SoCs (A64, H5,
etc).
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Reviewed-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some SoCs do not support clk delays for MMC in the clock control unit.
These include the old controllers in A10/A10s/A13/R8, and the new eMMC
controller in A64. The config structure for these controllers do not
specify clk_delays, but the check for this was replaced in change
"mmc: sunxi: Support controllers that can use both old and new timings".

This patch adds back the check for clk_delays, and also adds comments
for both checks in sunxi_mmc_clk_set_phase().
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Tested-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The third MMC controller (MMC2) on the Allwinner A83T SoC is slightly
different. It supports a wider 8-bit bus, has a dedicated controllable
reset pin for eMMC, and a "new timing mode" which is supposed to deliver
better signals and thus better performance.

Add a compatible for this one to use the new timing mode not found in the
other controllers.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The MMC controller can support DDR52 transfers under the new timing
mode. According to the BSP kernel, the module clock has to be double
the card clock, regardless of the bus width. The default timings in
the hardware can be used.

This also reworks the code setting the internal divider, getting rid
of a extra conditional.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

On the SoCs that introduced the new timing mode for MMC controllers,
both the old (where the clock delays are set in the CCU) and new
(where the clock delays are set in the MMC controller) timing modes
are available, and we have to support them both. However there are
two bits that control which mode is active. One is in the CCU, the
other is in the MMC controller. The settings on both sides must be
the same, or nothing will work.

The sunxi-ng clock driver provides an API to query and set the
active timing mode. At probe time, we try to set the active mode
to the "new timing mode". If it succeeds, we can then use the MMC
controller in the new mode. If not, we fall back to the old mode.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The mmc_host_ops structure is only stored in the ops field of an
mmc_host structure, which is declared as const.  Thus the mmc_host_ops
structure itself can be const.

Done with the help of Coccinelle.

// <smpl>
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct mmc_host_ops i@p = { ... };

@ok1@
struct mmc_host *mmc;
identifier r.i;
position p;
@@
mmc->ops = &i@p

@bad@
position p != {r.p,ok1.p};
identifier r.i;
struct mmc_host_ops e;
@@
e@i@p

@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
 struct mmc_host_ops i = { ... };
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Commit a53e35db ("reset: Ensure drivers are explicit when requesting
reset lines") started to transition the reset control request API calls
to explicitly state whether the driver needs exclusive or shared reset
control behavior. Convert all drivers requesting exclusive resets to the
explicit API call so the temporary transition helpers can be removed.

No functional changes.

Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The register for the "new timing mode" also has bit fields for setting
output and sample timing phases. According to comments in Allwinner's
BSP kernel, the default values are good enough.

Keep the default values already in the hardware when setting new timing
mode, instead of overwriting the whole register.

Fixes: 9a37e53e ("mmc: sunxi: Enable the new timings for the A64 MMC
controllers")
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Use new core function mmc_get_dma_dir().
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The controller's errors are usually normal (for example, for MMC or SDIO
cards, some errors are expected to happen; and for boards without a
dedicated card detect pin the error info will even flood console and
hide other normal messages) and hard to understand.

Change their print level to debug, thus it won't be shown to generic
users.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a bit more debug messages that can be helpful when debugging the clock
setup.

Also fill the actual_clock field in struct mmc_host to report properly the
current frequency in debugfs.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NFlorian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The MMC2 controller on the A64 is kind of a special beast.

While the general controller design is the same than the other MMC
controllers in the SoC, it also has a bunch of features and changes that
prevent it to be driven in the same way.

It has for example a different bus width limit, a different maximum
frequency, and, for some reason, the maximum buffer size of a DMA
descriptor.

Add a new compatible specifically for this controller.
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NFlorian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The A64 MMC controllers need DATA0 to be masked while updating the clock,
otherwise any subsequent command will result in a timeout.

It's not really clear at this point what DATA0 is exactly, but this
behaviour is present in Allwinner's tree, and has been suggested by
Allwinner engineers as fixes for the timeout.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NFlorian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The A64 MMC controllers need to set a "new timings" bit when a new rate is
set.

The actual meaning of that bit is not clear yet, but not setting it leads
to some corner-case issues, like the CMD53 failing, which is used to
implement SDIO packet aggregation.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NFlorian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Experience have shown that the using the  autocalibration could severely
degrade the performances of the MMC bus.

Allwinner is using in its BSP a delay set to 0 for all the modes but HS400.
Remove the calibration code for now, and add comments to document our
findings.
Reviewed-by: NAndre Przywara <andre.przywara@arm.com>
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NFlorian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The MMC core assumes that the code will gate the clock when the bus
frequency is set to 0, which we've been ignoring so far.

Handle that.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NFlorian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The SD specification documents that the clock frequency should only be
changed once gated (Section 3.2.3 - SD Clock Frequency Change Sequence).

The current code first modifies the parent clock, gates it and then
modifies the internal divider. This means that since the parent clock rate
might be changed, the bus clock might be changed as well before it is
gated, which breaks the specification.

Move the gating before the parent rate modification.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Tested-by: NFlorian Vaussard <florian.vaussard@heig-vd.ch>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

VMMC is an optional regulator, which means that mmc_regulator_get_supply
will only return an error in case of a deferred probe, but not when the
regulator is not set in the DT.

However, the sunxi driver assumes that VMMC is always there, and doesn't
check the value of the regulator pointer before using it, which obviously
leads to a (close to) null pointer dereference.

Add proper checks to prevent that.
Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

A64 SoC features a MMC controller which need only the mod clock, and can
calibrate delay by itself. This patch adds support for the new MMC
controller IP core.
Signed-off-by: NIcenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The sunxi-mmc driver does not take into account the processor may be big
endian when writing the DMA descriptors. This causes cards not to be
detected when running a big-endian kernel. Change the descriptors for
IDMA to use __le32 and ensure they are suitably swapped before writing.
Tested successfully on the Cubieboard2.
Signed-off-by: NMichael Weiser <michael.weiser@gmx.de>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

clk_round_rate() may return an error. Check it.
Signed-off-by: NJean-Francois Moine <moinejf@free.fr>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

It turns out that sun4i (A10) and sun5i (A13 & co) do not have sample
clocks, so add a new sun7i-a20-mmc compatible and do not try to use
sample clocks on sun4i / sun5i.

Since sun4i / sun5i do not have sample clocks, they cannot (reliably) do
DDR rates, so only set MMC_CAP_1_8V_DDR when we do have sample clks.

Note this patch leaves the clk_prepare_enable() / clk_disable_unprepare()
calls to the sample clks as-is, without adding checks for them being
NULL. All the clk_foo calls accept a NULL clk and will return success when
called with a NULL clk.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: NRob Herring <robh@kernel.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Add a sunxi_mmc_clk_set_phase() helper function.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Create a struct to hold the various model / compatible string dependend
settings.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

When support for the sample clks was added calls to prepare_enable
were added to the probe path, but matching calls to disable_unprepare
were forgotten in the remove path, this fixes this.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now the the HS-DDR mode clock timings have been corrected, we can
re-enable these modes on the A80.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The MMC clock timings were incorrectly calculated, when the conversion
from delay value to delay phase was done.

The 50M DDR and 50M DDR 8bit timings are off, and make eMMC DDR
unusable. Unfortunately it seems different controllers on the same SoC
have different timings. The new settings are taken from mmc2, which is
commonly used with eMMC.

The settings for the slower timing modes seem to work despite being
wrong, so leave them be.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

eMMC HS-DDR no longer works on the A80, despite it working when support
for this developed.

Disable it for now.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Remove the MMC_DATA_STREAM flag because it isn't used anymore.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Now that clock delay settings for 8 bit DDR are correct, and vqmmc
support is available, we can enable MMC_CAP_1_8V_DDR support. This
enables MMC HS-DDR at up to 52 MHz, even if signal voltage switching
is not available.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Allwinner's MMC controller needs to run at double the card clock rate
for 8 bit DDR transfer modes. Interestingly, this is not needed for
4 bit DDR transfers.

Different clock delays are needed for 8 bit eMMC DDR, due to the
increased module clock rate. For the A80 though, the same values for
4 bit and 8 bit are shared. The new values for the other SoCs were from
A83T user manual's "new timing mode" default values, which describes
them in clock phase, rather than delay periods. These values were used
without any modification. They may not be correct, but they work.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

DDR transfer modes include UHS-1 DDR50 and MMC HS-DDR (or MMC_DDR52).
Consider MMC_DDR52 when setting clock delays.

Since MMC high speed mode goes up to 52 MHz instead of 50 MHz for SD,
and this number is visible in the capability macro, increase the
clock rate upper limit to 52 MHz.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

eMMC chips require 2 power supplies, vmmc for internal logic, and vqmmc
for driving output buffers. vqmmc also controls signaling voltage. Most
boards we've seen use the same regulator for both, nevertheless the 2
have different usages, and should be set separately.

This patch adds support for vqmmc regulator supply, including voltage
switching. The MMC core can use this to try different signaling voltages
for eMMC.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Let .set_ios() fail if mmc_regulator_set_ocr() fails to enable and set a
proper voltage for vmmc.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

sunxi_mmc_init_host() originated from Allwinner kernel sources. The
magic numbers written to various registers was never documented.

Add comments for values found in Allwinner user manuals.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Acked-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>