There are several s390 diagnose calls, which must be executed below the
2GB memory boundary. In order to enforce this, those diagnoses must be
compiled into the kernel. Currently diag 14 can be called within the
vmur kernel module from addresses above 2GB. This leads to specification
exceptions. This patch moves diag10, diag14 and diag210 into the new
diag.c file.
Signed-off-by: NMichael Holzheu <holzheu@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

Hipersocket Multicast queue works asynchronously. When sending buffers,
the buffer state change may happen delayed. The tasklet for checking
changes in the outbound queue excluded IQDIO async queues from this
process. This created either a hang situation when the queue ran full,
or presented a hang situation a interface close time.
The tasklet processing is changed to include IQDIO async queues when
requesting buffer state refresh.
Signed-off-by: NKlaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

QDIO returned from EQBS instruction in any case after return code
CCQ=96 was issued regardless whether buffer states for at least one
buffer were extracted or not.
This caused FCP devices to hang when running under z/VM and having
QIOASSASIST=ON and having high I/O rates.
In order to fix this qdio return code processing of EQBS instruction
after CCQ=96 is changed that buffers are returned and if no buffers
where extracted the instruction is repeated at once.
Signed-off-by: NKlaus D. Wacker <kdwacker@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

cmf currently prints a message that more than 4096 channels are not
allowed in basic mode - however, this can only be enforced if cmf was
a module (which is no longer possible). It makes much more sense to
not check the specified number of channels and just print a message if
the block for basic mode could not be allocated (which may happen for
any number of specified channels).
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>

Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>

There are special PHY settings available on Yukon EC-U chip that
should not get cleared. This should solve mysterious errors on some
motherboards (like Gigabyte DS-3).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes handling of USB ISO completion error -EXDEV and includes
several other changes to current CVS version at isdn4linux.de (changes
in debug flags, style of code remarks, etc)
Signed-off-by: NMartin Bachem <info@colognechip.com>
Acked-by: NKarsten Keil <kkeil@suse.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This reverts commit 196705c9.  It was
reported to cause a regression by Daniel Exner, and Arjan van de Ven
points out that we actually already have infrastructure in place for
setting limits on acceptable DMA latency that would be the much more
correct fix for the problem with some Broadcom EHCI controllers.

Fixed up trivial conflicts due to the changes to support big-endian host
controller descriptors in drivers/usb/host/{ehci-sched.c,ehci.h}.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This disk reports total number of sectors instead of maximum sector address
in response to READ_NATIVE_MAX_ADDRESS command and also happily accepts
SET_MAX_ADDRESS command with the bogus value.  This results in +1 sector
capacity being used and errors on attempts to use the last sector.

...
hdd: Host Protected Area detected.
        current capacity is 78165360 sectors (40020 MB)
        native  capacity is 78165361 sectors (40020 MB)
hdd: Host Protected Area disabled.
...
hdd: reading: block=78165360, sectors=1, buffer=0xc1e63000
hdd: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hdd: dma_intr: error=0x10 { SectorIdNotFound }, LBAsect=78165360, sector=78165360
...

Add hpa_list[] table and workaround the issue in idedisk_check_hpa().

v2:
* Add missing export and improve patch description a bit.

v3:
* Add list termination.  (From Mikko)

Fixes kernel bugzilla bug #8816.

Thanks to Mikko for investigating the issue and helping with this patch.

Cc: Mikko Rapeli <mikko.rapeli@iki.fi>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Programming DMA mode may destroy current PIO mode setting so if
CONFIG_HPT34X_AUTODMA=n (the default case) make ide_tune_dma() fail
early by disabling all host DMA masks and re-tune PIO mode.

This fix doesn't help with the driver being broken but is needed
for some other changes.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.

Also this host driver requires valid PCI BAR4 for normal operation so
check it in ->init_chipset and fail initialization if not set.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

If ->dma_base is not set (== PCI BAR4 cannot be reserved) then DMA hooks
shouldn't be initialized or bad things will happen.

Also this host driver requires valid PCI BAR4 for normal operation so
check it in ->init_chipset and fail initialization if not set.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Use ->OUTBSYNC instead of ->OUTB when writing command register
  (needed for scc_pata and pmac host drivers).

* Don't check DRDY bit of the status register on ATAPI devices
  (ATAPI devices are free to ignore DRDY bit).

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Cc: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Move ide_in_drive_list() from ide-dma.c to ide-iops.c.

* Add ivb_list[] table for listening early UDMA66 devices which don't conform
  to ATA4 standard wrt cable detection (bit14 is zero, only bit13 is valid)
  and use only device side cable detection for them since host side cable
  detection may be unreliable.

* Add model "QUANTUM FIREBALLlct10 05" with firwmare "A03.0900" to the list
  (from Craig's bugreport).

v2:
* Improve kernel message basing on suggestion from Sergei.

v3:
* Don't print kernel message when no device side cable detection is done,
  plus some minor fixes.  (Noticed by Sergei)

Thanks to Craig for testing this patch.

Cc: Craig Block <chblock3@yahoo.com>
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

pmac_ide_tune_chipset() don't set drive->init_speed.

Fix it by setting drive->{current,init}_speed in pmac_ide_do_setfeature()
and clean up pmac_ide_{tune_chipset,mdma_enable,udma_enable}().
Acked-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add DMA blacklist checking (->ide_dma_on check probably can go now).

* Add ->atapi_dma flag checking and remove no longer needed
  ns87415_ide_dma_check() from ns87415 host driver.

* Remove now needless __ide_dma_check() wrapper and symbol export.

* Check drive->autodma instead of hwif->autodma (there should be no changes in
  behavior as all users of config_drive_for_dma() set both ->autodma flags).
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Some host drivers depend on CONFIG_IDE_GENERIC to do the probing but their
config options lack explicit dependencies on IDE_GENERIC.  In the long-term
these host drivers should be fixed to do the probing themselves but for now
fix them by making their config options select CONFIG_IDE_GENERIC.
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

These days, CONFIG_IDE_GENERIC causes more confusion and
misconfiguration than it helps.  Especially so because libata is
linked after the generic driver.  Default to N.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Acked-by: NJeff Garzik <jeff@garzik.org>
Cc: "P.C.Chan" <pc.chan@alcatel-lucent.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Configuring the OLPC camera requires something over 150 register
writes.  Unfortunately, querying the CAFE i2c controller too
soon after a write causes the hardware to flake.  The problem had
been "solved" with an msleep() call, but, between the number of
registers and how msleep() behaves, that resulted in a 3-second
delay on camera initialization.  Instead, we hand-code a wait for
the completion interrupt which avoids reading the status registers.
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NJonathan Corbet <corbet@lwn.net>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The tuner maximum frequency wasn't being set, while the minimum 
frequency was set to what the maximum should have been.

If a future patch were to enforce these limits, dvb-pll would be 
effectively broken.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

ivtv: fix VIDIOC_S_FBUF support: new OSD values where never actually set.

The values set with VIDIOC_S_FBUF were not actually used until the next
VIDIOC_S_FMT. Fixed.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

When taking a cpu down, we need to hardware_disable() it.
Unfortunately, the CPU_DYING notifier is called with interrupts
disabled, which means we can't use smp_call_function_single().

Fortunately, the CPU_DYING notifier is always called on the dying cpu,
so we don't need to use the function at all and can simply call
hardware_disable() directly.
Tested-by: NPaolo Ornati <ornati@fastwebnet.it>
Signed-off-by: NAvi Kivity <avi@qumranet.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If the forcedeth driver receives too much work in an interrupt, it
assumes it has a broken hardware with stuck IRQ.  It works around the
problem by disabling interrupts on the nic but makes a printk while
holding device spinlog - which isn't smart thing to do if you have
netconsole on the same nic.

This patch moves the printk's out of the spinlock protected area.

Without this patch the machine hangs hard.  With this patch everything
still works even when there is significant increase on CPU usage while
using the nic.
Signed-off-by: NTimo Jantunen <jeti@iki.fi>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (edited MACINTOSH_DRIVERS per Geert Uytterhoeven's remark)
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The lguest block device only requests one minor, which means
partitions don't work (eg "root=/dev/lgba1").

Let's follow the crowd and ask for 16.
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

A stray semicolon makes us inadvertently ignore the value of err.
Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Adjust libata to ignore errors after spinup

This patch is to ignore errors from the spinup attempt if the drive is
in the "standby id" state.
Signed-off-by: NRyan Power <rpower@sysreset.com>
Acked-by: NMark Lord <liml@rtr.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add TECRA M7 to broken suspend list.  Reported by Marie Koreen.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: Marie Koreen <kbug@koreen.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix several inconsistencies in these drivers WRT reporting the clocks:

- when using DPLL mode, 'pata_hpt37x' driver reported the DPLL frequency as the
  PCI clock -- make it properly report both clocks and add the same ability to
  the 'pata_hpt3x2n' driver;

- both drivers sometimes use "pata_hpt3*:" and sometimes "hpt3*:" in the
  messages -- make them use only the former one;

- the message about failed DPLL stablizatios deserves KERN_ERR and a bang. :-)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The DPLL tuning code always set up it for 66 MHz due to wrong UltraDMA mask
including mode 5 used to check for the necessity of 66 MHz clocking -- this
caused 66 MHz clock to be used for HPT374 chip that does not tolerate it.
While fixing this, also remove PLL mode from the TODO list -- I don't think
it's still a relevant item.
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Maximum supported UDMA mode for AEC6280[R] is UDMA5 (not UDMA4)
and for AEC6880[R] it is UDMA6 (not UDMA5):

* Fix the problem by adding missing struct ata_port_info to artop_init_one().

* Use the right naming (s/626/628/).

* Bump driver version.

Fixes IDE->libata regression, problem was never present in IDE aec62xx driver.

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Fix map entry 10b for ich8.  It's [P0 P2 IDE IDE] like ich6 / ich6m.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Cc: <Kristen Carlson Accardi> kristen.c.accardi@intel.com
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Underneath all the HPT packaging, PCI identifiers, binary driver modules
and stuff you find that ...
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NJeff Garzik <jeff@garzik.org>