pata_hpt{37x|3x2n}: fix clock reporting (take 2)

Fix several inconsistencies in these drivers WRT reporting the clocks:

- when using DPLL mode, 'pata_hpt37x' driver reported the DPLL frequency as the
  PCI clock -- make it properly report both clocks and add the same ability to
  the 'pata_hpt3x2n' driver;

- both drivers sometimes use "pata_hpt3*:" and sometimes "hpt3*:" in the
  messages -- make them use only the former one;

- the message about failed DPLL stablizatios deserves KERN_ERR and a bang. :-)
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

drivers/ata/pata_hpt37x.c

@@ -24,7 +24,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"pata_hpt37x"
-#define DRV_VERSION	"0.6.8"
+#define DRV_VERSION	"0.6.9"
 
 struct hpt_clock {
 	u8	xfer_speed;
@@ -1112,7 +1112,7 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 			pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low | 0x100);
 		}
 		if (adjust == 8) {
-			printk(KERN_WARNING "hpt37x: DPLL did not stabilize.\n");
+			printk(KERN_ERR "pata_hpt37x: DPLL did not stabilize!\n");
 			return -ENODEV;
 		}
 		if (dpll == 3)
@@ -1120,7 +1120,8 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 		else
 			private_data = (void *)hpt37x_timings_50;
 
-		printk(KERN_INFO "hpt37x: Bus clock %dMHz, using DPLL.\n", MHz[dpll]);
+		printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using %dMHz DPLL.\n",
+		       MHz[clock_slot], MHz[dpll]);
 	} else {
 		private_data = (void *)chip_table->clocks[clock_slot];
 		/*
@@ -1133,7 +1134,8 @@ static int hpt37x_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 			port = &info_hpt370_33;
 		if (clock_slot < 2 && port == &info_hpt370a)
 			port = &info_hpt370a_33;
-		printk(KERN_INFO "hpt37x: %s: Bus clock %dMHz.\n", chip_table->name, MHz[clock_slot]);
+		printk(KERN_INFO "pata_hpt37x: %s using %dMHz bus clock.\n",
+		       chip_table->name, MHz[clock_slot]);
 	}
 
 	/* Now kick off ATA set up */

drivers/ata/pata_hpt3x2n.c

@@ -8,7 +8,7 @@
  * Copyright (C) 1999-2003		Andre Hedrick <andre@linux-ide.org>
  * Portions Copyright (C) 2001	        Sun Microsystems, Inc.
  * Portions Copyright (C) 2003		Red Hat Inc
- * Portions Copyright (C) 2005-2006	MontaVista Software, Inc.
+ * Portions Copyright (C) 2005-2007	MontaVista Software, Inc.
  *
  *
  * TODO
@@ -25,7 +25,7 @@
 #include <linux/libata.h>
 
 #define DRV_NAME	"pata_hpt3x2n"
-#define DRV_VERSION	"0.3.3"
+#define DRV_VERSION	"0.3.4"
 
 enum {
 	HPT_PCI_FAST	=	(1 << 31),
@@ -579,10 +579,12 @@ static int hpt3x2n_init_one(struct pci_dev *dev, const struct pci_device_id *id)
 		pci_write_config_dword(dev, 0x5C, (f_high << 16) | f_low);
 	}
 	if (adjust == 8) {
-		printk(KERN_WARNING "hpt3x2n: DPLL did not stabilize.\n");
+		printk(KERN_ERR "pata_hpt3x2n: DPLL did not stabilize!\n");
 		return -ENODEV;
 	}
 
+	printk(KERN_INFO "pata_hpt37x: bus clock %dMHz, using 66MHz DPLL.\n",
+	       pci_mhz);
 	/* Set our private data up. We only need a few flags so we use
 	   it directly */
 	port.private_data = NULL;