It is really useful not only for debugging to have an IRQ line and DMA
pool labeled with driver and its instance ID. Do this for DesignWare DMA
driver.

All current users of this IP would be enhanced later on.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

When transferring more data than the maximum block size supported by the
HW multiplied by source width the transfer is split into smaller chunks.
Currently code calculates the memory width and thus aligment before
splitting for both memory to device and device to memory transfers.

For memory to device transfers this work fine since alignment is preserved
through the splitting and split blocks are still memory width aligned.
However in device to memory transfers aligment breaks when maximum block
size multiplied by register width doesn't have the same alignment than the
buffer. For instance when transferring from an 8-bit register 4100 bytes
(32-bit aligned) on a DW DMA that has maximum block size of 4095 elements.
An attempt to do such transfers caused data corruption.

Fix this by calculating and setting the destination memory width after
splitting by using the split block aligment and length.
Signed-off-by: NJarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

LPE Audio driver should take care of DMA IPs by itself. Keeping an ID like this
in dw_dma_pci.c is anyway wrong since that block has two DMA controllers under
one ID (like MFD device).

That's also why I didn't include LPE Audio ID for Intel Merrifield previously.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NVinod Koul <vinod.koul@intel.com>

Fixing the gmac4 mdio write access to use MII_GMAC4_WRITE only instead of
OR together with MII_WRITE.
Signed-off-by: NKweh, Hock Leong <hock.leong.kweh@intel.com>
Acked-By: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This chip is the same as RTL8168, but its device id is 0x8161.
Signed-off-by: NChun-Hao Lin <hau@realtek.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit beb0babf ("korina: disable napi on close and restart")
introduced calls to napi_disable() that were missing before,
unfortunately this leaves a small window during which NAPI has a chance
to run, yet we just freed resources since korina_free_ring() has been
called:

Fix this by disabling NAPI first then freeing resource, and make sure
that we also cancel the restart task before doing the resource freeing.

Fixes: beb0babf ("korina: disable napi on close and restart")
Reported-by: NAlexandros C. Couloumbis <alex@ozo.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The timer type simplifications caused a new gcc warning:

  drivers/base/power/domain.c: In function ‘genpd_runtime_suspend’:
  drivers/base/power/domain.c:562:14: warning: ‘time_start’ may be used uninitialized in this function [-Wmaybe-uninitialized]
     elapsed_ns = ktime_to_ns(ktime_sub(ktime_get(), time_start));

despite the actual use of "time_start" not having changed in any way.
It appears that simply changing the type of ktime_t from a union to a
plain scalar type made gcc check the use.

The variable wasn't actually used uninitialized, but gcc apparently
failed to notice that the conditional around the use was exactly the
same as the conditional around the initialization of that variable.

Add an unnecessary initialization just to shut up the compiler.
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

ktime_set(S,N) was required for the timespec storage type and is still
useful for situations where a Seconds and Nanoseconds part of a time value
needs to be converted. For anything where the Seconds argument is 0, this
is pointless and can be replaced with a simple assignment.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

ktime is a union because the initial implementation stored the time in
scalar nanoseconds on 64 bit machine and in a endianess optimized timespec
variant for 32bit machines. The Y2038 cleanup removed the timespec variant
and switched everything to scalar nanoseconds. The union remained, but
become completely pointless.

Get rid of the union and just keep ktime_t as simple typedef of type s64.

The conversion was done with coccinelle and some manual mopping up.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>

There is no point in having an extra type for extra confusion. u64 is
unambiguous.

Conversion was done with the following coccinelle script:

@rem@
@@
-typedef u64 cycle_t;

@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>

The mpic is either the main interrupt controller or is cascaded behind a
GIC. The mpic is single instance and the modes are mutually exclusive, so
there is no reason to have seperate cpu hotplug states.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: http://lkml.kernel.org/r/20161221192112.333161745@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Even if both drivers are compiled in only one instance can run on a given
system depending on the available GIC version.

So having seperate hotplug states for them is pointless.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.252416267@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Even if both drivers are compiled in only one instance can run on a given
system depending on the available tracer cell.

So having seperate hotplug states for them is pointless.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Link: http://lkml.kernel.org/r/20161221192112.162765484@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.

Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Install the callbacks via the state machine. No functional change.
Signed-off-by: NAnna-Maria Gleixner <anna-maria@linutronix.de>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: devel@driverdev.osuosl.org
Cc: Andreas Dilger <andreas.dilger@intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: rt@linutronix.de
Cc: lustre-devel@lists.lustre.org
Link: http://lkml.kernel.org/r/20161202110027.htzzeervzkoc4muv@linutronix.de
Link: http://lkml.kernel.org/r/20161221192111.922872524@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Install the callbacks via the state machine. No functional change.

This is the minimal fixup so we can remove the hotplug notifier mess
completely.

The real rework of this driver to use work queues is still stuck in
review/testing on the SCSI mailing list.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20161221192111.836895753@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Install the callbacks via the state machine. No functional change.

This is the minimal fixup so we can remove the hotplug notifier mess
completely.

The real rework of this driver to use work queues is still stuck in
review/testing on the SCSI mailing list.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: "James E.J. Bottomley" <jejb@linux.vnet.ibm.com>
Cc: linux-scsi@vger.kernel.org
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: QLogic-Storage-Upstream@qlogic.com
Cc: Johannes Thumshirn <jth@kernel.org>
Cc: Christoph Hellwig <hch@lst.de>
Link: http://lkml.kernel.org/r/20161221192111.757309869@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

In case the driver registration fails, the hotplug callback is leaked.

Not fatal, because it's never invoked as there are no instances registered,
but wrong nevertheless.

Fixes: fdc15a36 ("bus/arm-ccn: Convert to hotplug statemachine")
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Will Deacon <will.deacon@arm.com>

The CPU hotplug code is a trainwreck. It leaks a notifier in case of driver
registration error and the per cpu loop is racy against cpu hotplug. Aside
of that the driver should have been written and merged with the new state
machine interfaces in the first place.

Mop up the mess and Convert it to the hotplug state machine.
Signed-off-by: NThomas Grumpy Gleixner <tglx@linutronix.de>
Cc: Nilesh Javali <nilesh.javali@cavium.com>
Cc: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@cavium.com>
Cc: Saurav Kashyap <saurav.kashyap@cavium.com>
Cc: Arun Easi <arun.easi@cavium.com>
Cc: Manish Rangankar <manish.rangankar@cavium.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>

This was entirely automated, using the script by Al:

  PATT='^[[:blank:]]*#[[:blank:]]*include[[:blank:]]*<asm/uaccess.h>'
  sed -i -e "s!$PATT!#include <linux/uaccess.h>!" \
        $(git grep -l "$PATT"|grep -v ^include/linux/uaccess.h)

to do the replacement at the end of the merge window.
Requested-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The user prio field is wrong (and overflows) in the XDP forward
flow.
This is a result of a bad value for num_tx_rings_p_up, which should
account all XDP TX rings, as they operate for the same user prio.
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Reported-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In an IPvlan setup when master is set in loopback mode e.g.

  ethtool -K eth0 set loopback on

  where eth0 is master device for IPvlan setup.

The failure is caused by the faulty logic that determines if the
packet is from TX-path vs. RX-path by just looking at the mac-
addresses on the packet while processing multicast packets.

In the loopback-mode where this crash was happening, the packets
that are sent out are reflected by the NIC and are processed on
the RX path, but mac-address check tricks into thinking this
packet is from TX path and falsely uses dev_forward_skb() to pass
packets to the slave (virtual) devices.

This patch records the path while queueing packets and eliminates
logic of looking at mac-addresses for the same decision.

------------[ cut here ]------------
kernel BUG at include/linux/skbuff.h:1737!
Call Trace:
 [<ffffffff921fbbc2>] dev_forward_skb+0x92/0xd0
 [<ffffffffc031ac65>] ipvlan_process_multicast+0x395/0x4c0 [ipvlan]
 [<ffffffffc031a9a7>] ? ipvlan_process_multicast+0xd7/0x4c0 [ipvlan]
 [<ffffffff91cdfea7>] ? process_one_work+0x147/0x660
 [<ffffffff91cdff09>] process_one_work+0x1a9/0x660
 [<ffffffff91cdfea7>] ? process_one_work+0x147/0x660
 [<ffffffff91ce086d>] worker_thread+0x11d/0x360
 [<ffffffff91ce0750>] ? rescuer_thread+0x350/0x350
 [<ffffffff91ce960b>] kthread+0xdb/0xe0
 [<ffffffff91c05c70>] ? _raw_spin_unlock_irq+0x30/0x50
 [<ffffffff91ce9530>] ? flush_kthread_worker+0xc0/0xc0
 [<ffffffff92348b7a>] ret_from_fork+0x9a/0xd0
 [<ffffffff91ce9530>] ? flush_kthread_worker+0xc0/0xc0

Fixes: ba35f858 ("ipvlan: Defer multicast / broadcast processing to a work-queue")
Signed-off-by: NMahesh Bandewar <maheshb@google.com>
CC: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) netif_rx() / dev_forward_skb() should not be called from process
context.

2) ipvlan_count_rx() should be called with preemption disabled.

3) We should check if ipvlan->dev is up before feeding packets
to netif_rx()

4) We need to prevent device from disappearing if some packets
are in the multicast backlog.

5) One kfree_skb() should be a consume_skb() eventually

Fixes: ba35f858 ("ipvlan: Defer multicast / broadcast processing to
a work-queue")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The results were previously ignored, anyway.
Signed-off-by: NSteve Wahl <Steve.Wahl@dell.com>
Fixes: e26a5843Acked-by: NAllen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

'request_irq()' and 'free_irq()' should have the same 'dev_id'.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: NDave Jiang <dave.jiang@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The offsets for the SZ registers are wrong. Updated.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Reported-by: NSandeep Mann <sandeep@purestorage.com>
Tested-by: NZachary Ross <zacharyx.ross@intel.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

When the underlying NTB H/W driver advertises more memory windows
than the number of scratchpads available to setup MW's, it is likely
that we may end up filling the remaining memory windows with garbage.
So to avoid that, lets limit the memory windows that transport driver
can setup based on the available scratchpads.
Signed-off-by: NShyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: NAllen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Due to incorrect limit and translation register values, NTB link was
going down when the memory window was setup. Made appropriate changes
as per spec.

Fix limit register values for BAR1, which was overlapping
with the BAR23 address.
Signed-off-by: NShyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: NAllen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

AMD NTB support hotplug under B2B mode. NTB will trigger link
up/down interrupt event when doing plug add/remove, this patch
implements the two interrupt event to support B2B hotplug function.
Signed-off-by: NXiangliang Yu <Xiangliang.Yu@amd.com>
Signed-off-by: NShyam Sundar S K <Shyam-sundar.S-k@amd.com>
Acked-by: NAllen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

The Skylake Xeon NTB hardware has made some changes to the register name,
offset, and the way doorbells work. Adding driver support for the new
hardware.
Signed-off-by: NDave Jiang <dave.jiang@intel.com>
Acked-by: NAllen Hubbe <Allen.Hubbe@dell.com>
Signed-off-by: NJon Mason <jdmason@kudzu.us>

Commit f600b690 ("virtio_net: Add XDP support") leaves the case of
small receive buffer untouched. This will confuse the user who want to
set XDP but use small buffers. Other than forbid XDP in small buffer
mode, let's make it work. XDP then can only work at skb->data since
virtio-net create skbs during refill, this is sub optimal which could
be optimized in the future.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now we in fact don't allow XDP for big packets, remove its codes.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When VIRTIO_NET_F_GUEST_UFO is negotiated, host could still send UFO
packet that exceeds a single page which could not be handled
correctly by XDP. So this patch forbids setting XDP when GUEST_UFO is
supported. While at it, forbid XDP for ECN (which comes only from GRO)
too to prevent user from misconfiguration.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't update ewma rx buf size in the case of XDP. This will lead
underestimation of rx buf size which causes host to produce more than
one buffers. This will greatly increase the possibility of XDP page
linearization.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We drop csumed packet when do XDP for packets. This breaks
XDP_PASS when GUEST_CSUM is supported. Fix this by allowing csum flag
to be set. With this patch, simple TCP works for XDP_PASS.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When XDP_PASS were determined for linearized packets, we try to get
new buffers in the virtqueue and build skbs from them. This is wrong,
we should create skbs based on existed buffers instead. Fixing them by
creating skb based on xdp_page.

With this patch "ping 192.168.100.4 -s 3900 -M do" works for XDP_PASS.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We don't put page during linearizing, the would cause leaking when
xmit through XDP_TX or the packet exceeds PAGE_SIZE. Fix them by
put page accordingly. Also decrease the number of buffers during
linearizing to make sure caller can free buffers correctly when packet
exceeds PAGE_SIZE. With this patch, we won't get OOM after linearize
huge number of packets.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After we linearize page, we should xmit this page instead of the page
of first buffer which may lead unexpected result. With this patch, we
can see correct packet during XDP_TX.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we use EWMA to estimate the size of rx buffer. When rx buffer
size is underestimated, it's usual to have a packet with more than one
buffers. Consider this is not a bug, remove the warning and correct
the comment before XDP linearizing.

Cc: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the end of the nexthop initialization process we determine whether
the nexthop should be offloaded or not based on the NUD state of the
neighbour representing it. After all the nexthops were initialized we
refresh the nexthop group and potentially offload it to the device, in
case some of the nexthops were resolved.

Make the destruction of a nexthop group symmetric with its creation by
marking all nexthops as invalid and then refresh the nexthop group to
make sure it was removed from the device's tables.

Fixes: b2157149 ("mlxsw: spectrum_router: Add the nexthop neigh activity update")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>