We were using -mno-minimal-toc on everything in arch/powerpc/kernel,
which means that all the functions in there were putting all their
TOC entries in the top-level TOC, and it was overflowing on an
allyesconfig build.  For various reasons, prom_init.c does need
-mno-minimal-toc, but the other .c files in there can use sub-TOCs
quite happily.  This change is sufficient for now to stop the TOC
overflowing; other directories under arch/powerpc also use
-mno-minimal-toc and could also be changed later if necessary.

Lmbench runs with and without this patch showed no significant speed
differences.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The PCI IRQ code has a fallback when the device-tree parsing fails, that
tries to map the interrupt indicated by PCI_INTERRUPT_LINE if the firmware
set something in there. This is a bit fragile but has proven useful in some
cases so far. However, it's causing us to incorrectly try to map interrupt 0
on various setups, so let's prevent that case, as none of the cases where
the fallback is legit should have an IRQ 0.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch changes the PowerPC PCI code to disable IO and/or Memory
decoding on a PCI device when a resource of that type failed to be
allocated.  This is done to avoid having unallocated dangling BARs
enabled that might try to decode on top of other devices.

If a proper resource is assigned later on, then pci_enable_device()
will take care of re-enabling decoding.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Apple firmware has a strange way to "close" bridge resources by setting
them to some bogus values that overlap RAM (strangely, I haven't seen it
conflicting with DMA so far...).  This explicitely closes them to avoid
problems.  Previously, they would be closed as a consequence of failing
to be allocated, but this makes it more explicit, and thus the log
message is more explicit too.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The device node for the HT bridge on G5s doesn't contain useful ranges.

We used to give it a bunch of the known PCI space and then punch a "hole"
in it based on where the AGP or PCIe region was.  This reworks it to
use the actual register in the bridge that controls the decoding instead.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This enables the PCI code to see the device that represents the
HT host bridge on the PowerMac G5.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Our implementation of pcibios_enable_device() has a couple of problems.

One is that it should not check IORESOURCE_UNSET, as this might be
left dangling after resource assignment (shouldn't but there are
bugs), but instead, we make it check resource->parent which should
be a reliable indication that the resource has been successfully
claimed (it's in the resource tree).

Then, we also need to skip ROM resources that haven't been enabled
as x86 does.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

It should now be safe to re-assign unassigned resources on 64 bits PowerMac
machines (G5s).  This clears pci_probe_only on those.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Powermac's use of the pcibios_enable_device_hook() got slightly
broken by the recent PCI merge in that it won't be called for
the "initial" case of assigning resources to a previously
unassigned device.  This was an abuse of that hook anyway, so
instead we now use a header quirk.

While at it, we move a #ifdef CONFIG_PPC32 to enclose more code
that is only ever used on 32 bits.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This merge the two implementations, based on the previously
fixed up 32 bits one.  The pcibios_enable_device_hook in ppc_md
is now available for ppc64 use.  Also remove the new unused
"initial" parameter from it and fixup users.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Our implementation of pcibios_enable_device() incorrectly ignores
the mask argument and always checks that all resources have been
allocated, which isn't the right thing to do anymore.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The way iSeries manages PCI IO and Memory resources is a bit strange
and is based on overriding the content of those resources with home
cooked ones afterward.

This changes it a bit to better integrate with the new resource handling
so that the "virtual" tokens that iSeries replaces resources with are
done from the proper per-device fixup hook, and bridge resources are
set to enclose that token space.  This fixes various things such as
the output of /proc/iomem & ioports, among others.  This also fixes up
various boot messages as well.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The 32 bits PCI code now uses the generic code for assigning unassigned
resources and an algorithm similar to x86 for claiming existing ones.

This works far better than the 64 bits code which basically can only
claim existing ones (pci_probe_only=1) or would fall apart completely.

This merges them so that the new 32 bits implementation is used for both.

64 bits now gets the new PCI flags for controlling the behaviour, though
the old pci_probe_only global is still there for now to be cleared if you
want to.

I kept a pcibios_claim_one_bus() function mostly based on the old 64
bits code for use by the DLPAR hotplug. This will have to be cleaned
up, thought I hope it will work in the meantime.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The PCI code in 32 and 64 bits fixes up resources differently.

32 bits uses a header quirk plus handles bridges in pcibios_fixup_bus()
while 64 bits does things in various places depending on whether you
are using OF probing, using PCI hotplug, etc...

This merges those by basically using the 32 bits approach for both,
with various tweaks to make 64 bits work with the new approach.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This merges the PowerPC 32 and 64 bits version of pcibios_resource_to_bus
and pcibios_bus_to_resource().
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds flags the platforms can use to enable domain numbers
in /proc/bus/pci.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The 32 bits PCI code carries an old hack that was only useful for G5
machines.  Nowdays, the 32 bits kernel doesn't support any of those
machines anymore so the hack is basically never used, so remove it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This adds to the 32 bits PCI code some flags, replacing the old
pci_assign_all_busses global, that allow us to control various
aspects of the PCI probing, such as whether to re-assign all
resources or not, or to not try to assign anything at all.

This also adds the flag x86 already has to avoid ISA alignment
on bridges that don't have ISA forwarding enabled (no legacy
devices on the top level bus) and sets it for PowerMacs.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The 32 bits PowerPC PCI code has a hack for use by some PowerMacs
to try to re-open PCI<->PCI bridge IO resources that were closed
by the firmware.  This is no longer necessary as the generic code
will now do that for us.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This makes the 32 bits PowerPC PCI code use the generic code to assign
resources to devices that had unassigned or conflicting resources.

This allow us to remove the local implementation that was incomplete and
could not assign for example a PCI<->PCI bridge from scratch, which is
needed on various embedded platforms.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There's a stale & bogus piece of code in 32 bits PCI code that
complains about ISA related alignment issues.  Just remove it.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch alters the kernel makefiles to build dtc from the sources
embedded in the previous patch.  It also changes the
arch/powerpc/boot/wrapper script to use the embedded dtc, rather than
expecting a copy of dtc already installed on the system.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This incorporates a copy of dtc into the kernel source, in
arch/powerpc/boot/dtc-src.  This commit only imports the upstream
sources verbatim, a later commit will actually link it into the kernel
Makefiles and use the embedded code during the kernel build.
Signed-off-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

There's nothing in holly.c that needs linux/ide.h, just remove it from
the list of includes.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NJosh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

PowerPC currently doesn't implement pci_set_dma_mask(), which means drivers
calling it will get the generic version in drivers/pci/pci.c.

The powerpc dma mapping ops include a dma_set_mask() hook, which luckily is
not implemented by anyone - so there is no bug in the fact that the hook
is currently never called.

However in future we'll add implementation(s) of dma_set_mask(), and so we
need pci_set_dma_mask() to call the hook.

To save adding a hook to the dma mapping ops, pci-set_consistent_dma_mask()
simply calls the dma_set_mask() hook and then copies the new mask into
dev.coherenet_dma_mask.
Signed-off-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

We have multiple calls to has_feature being inlined, but gcc can't
be sure that the store via get_paca() doesn't alias the path to
cur_cpu_spec->feature.

Reorder to put the calls to read_purr and read_spurr adjacent to each
other.  To add a sense of consistency, reorder the remaining lines to
perform parallel steps on purr and scaled purr of each line instead of
calculating and then using one value before going on to the next.

In addition, we can tell gcc that no SPURR means no PURR.  The test is
completely hidden in the PURR case, and in the !PURR case the second test
is eliminated resulting in the simple register copy in the out-of-line
branch.

Further, gcc sees get_paca()->system_time referenced several times and
allocates a register to address it (shadowing r13) instead of caching its
value.  Reading into a local varable saves the shadow of r13 and removes
a potentially duplicate load (between the nested if and its parent).
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If CPU_FTR_PURR is not set, we will never set cpu_purr_data->initialized.
Checking via __get_cpu_var on 64 bit avoids one dependent load compared
to cpu_has_feature in the not-present case, and is always required when
it is present.  The code is under CONFIG_VIRT_CPU_ACCOUNTING so 32 bit
will not be affected.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

timer_interrupt() was calculating per_cpu_offset several times, having to
start from the toc because of potential aliasing issues.

Placing both decrementer per_cpu varables in a struct and calculating
the address once with __get_cpu_var results in better code on both 32
and 64 bit.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Use __get_cpu_var(x) instead of per_cpu(x, smp_processor_id()), as it
is optimized on ppc64 to access the current cpu's per-cpu offset directly;
it's local_paca.offset instead of TOC->paca[local_paca->processor_id].offset.

This is the trivial portion, two functions with one use each.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

as its only called from time_init, which is __init.

Also remove unneeded forward declaration.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The per-processor interrupt request register and current processor
priority register are only accessed on the current cpu.  In fact the
hypervisor doesn't even let us choose which cpu's registers to access.

The only function to use cpu twice is xics_migrate_irqs_away, not a fast
path.  But we can cache the result of get_hard_processor_id() instead of
calling get_hard_smp_processor_id(cpu) in a loop across the call to rtas.

Years ago the irq code passed smp_processor_id into get_irq, I thought
we might initialize the CPPR third party at boot as an extra measure of
saftey, and it made the code symmetric with the qirr (queued interrupt
for software generated interrupts), but now it is just extra and
sometimes unneeded work to pass it down.
Signed-off-by: NMilton Miller <miltonm@bga.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This splits the machine definition for celleb into two definitions,
one for celleb_beat, and the other for celleb_native.  Though this
looks complex because of sorting some functions, there are no
more semantic changes than that for the splitting.
Signed-off-by: NKou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This makes mmio_nvram_init() callable unconditionally by providing
a dummy definition when CONFIG_MMIO_NVRAM is not defined.
Signed-off-by: NKou Ishizaki <Kou.Ishizaki@toshiba.co.jp>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Implement MSI support for PA Semi PWRficient platforms. MSI is done
through a special range of sources on the openpic controller, and they're
unfortunately breaking the usual concepts of how sources are programmed:

* The source is calculated as 512 + the value written into the MSI
  register
* The vector for this source is added to the source and reported
  through IACK

This means that for simplicity, it makes much more sense to just set the
vector to 0 for the source, since that's really the vector we expect to
see from IACK.

Also, the affinity/priority registers will affect 16 sources at a
time. To avoid most (simple) users from being limited by this, allocate
16 sources per device but use only one. This means that there's a total
of 32 sources.

If we get usage scenarions that need more sources, the allocator should
probably be revised to take an alignment argument and size, not just do
natural alignment.

Finally, since I'm already touching the MPIC names on pasemi, rename
the base one from the somewhat odd " PAS-OPIC  " to "PASEMI-OPIC".
Signed-off-by: NOlof Johansson <olof@lixom.net>
Acked-by: NMichael Ellerman <michael@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Commit fbd568a3 ("Change
synchronize_kernel to _rcu and _sched") changed the deprecated
synchronize_kernel() in HvLpEvent_unregisterHandler() to
synchronize_rcu().  It turns out that it should have been
synchronize_sched().
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NPaul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Many operations, as currently used in the wrapper, assume they can
pass NULL and have it be treated as the root node.  However, libfdt-wrapper
converts NULL to -1, which is only appropriate when searching for nodes,
and will cause an error otherwise.
Signed-off-by: NScott Wood <scottwood@freescale.com>
Acked-by: NDavid Gibson <david@gibson.dropbear.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>