Noticed-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NNeilBrown <neilb@suse.de>

commit 589a594b (2.6.37-rc4) fixed a problem were md_thread would
sometimes call the ->run function at a bad time.

If an error is detected during array start up after the md_thread has
been started, the md_thread is killed.  This resulted in the ->run
function being called once.  However the array may not be in a state
that it is safe to call ->run.

However the fix imposed meant that  ->run was not called on a timeout.
This means that when an array goes idle, bitmap bits do not get
cleared promptly.  While the array is busy the bits will still be
cleared when appropriate so this is not very serious.  There is no
risk to data.

Change the test so that we only avoid calling ->run when the thread
is being stopped.  This more explicitly addresses the problem situation.

This is suitable for 2.6.37-stable and any -stable kernel to which
589a594b was applied.

Cc: stable@kernel.org
Signed-off-by: NNeilBrown <neilb@suse.de>

Commit 1a855a06 (2.6.37-rc4) fixed a problem where devices were
re-added when they shouldn't be but caused a regression in a less
common case that means sometimes devices cannot be re-added when they
should be.

In particular, when re-adding a device to an array without metadata
we should always access the device, but after the above commit we
didn't.

This patch sets the In_sync flag in that case so that the re-add
succeeds.

This patch is suitable for any -stable kernel to which 1a855a06 was
applied.

Cc: stable@kernel.org
Signed-off-by: NNeilBrown <neilb@suse.de>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  ipv4/route.c: respect prefsrc for local routes
  bridge: stp: ensure mac header is set
  bridge: fix br_multicast_ipv6_rcv for paged skbs
  atl1: fix oops when changing tx/rx ring params
  drivers/atm/atmtcp.c: add missing atm_dev_put
  starfire: Fix dma_addr_t size test for MIPS
  tg3: fix return value check in tg3_read_vpd()
  Broadcom CNIC core network driver: fix mem leak on allocation failures in cnic_alloc_uio_rings()
  ISDN, Gigaset: Fix memory leak in do_disconnect_req()
  CAN: Use inode instead of kernel address for /proc file
  skfp: testing the wrong variable in skfp_driver_init()
  ppp: allow disabling multilink protocol ID compression
  ehea: Avoid changing vlan flags
  ueagle-atm: fix PHY signal initialization race

The preferred source address is currently ignored for local routes,
which results in all local connections having a src address that is the
same as the local dst address. Fix this by respecting the preferred source
address when it is provided for local routes.

This bug can be demonstrated as follows:

 # ifconfig dummy0 192.168.0.1
 # ip route show table local | grep local.*dummy0
 local 192.168.0.1 dev dummy0  proto kernel  scope host  src 192.168.0.1
 # ip route change table local local 192.168.0.1 dev dummy0 \
     proto kernel scope host src 127.0.0.1
 # ip route show table local | grep local.*dummy0
 local 192.168.0.1 dev dummy0  proto kernel  scope host  src 127.0.0.1

We now establish a local connection and verify the source IP
address selection:

 # nc -l 192.168.0.1 3128 &
 # nc 192.168.0.1 3128 &
 # netstat -ant | grep 192.168.0.1:3128.*EST
 tcp        0      0 192.168.0.1:3128        192.168.0.1:33228 ESTABLISHED
 tcp        0      0 192.168.0.1:33228       192.168.0.1:3128  ESTABLISHED
Signed-off-by: NJoel Sing <jsing@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ->trim_fs has been removed meanwhile, so remove it from the documentation
as well.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reported-by: NRyusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* master.kernel.org:/home/rmk/linux-2.6-arm:
  ARM: pxa: fix page table corruption on resume
  ARM: it8152: add IT8152_LAST_IRQ definition to fix build error
  ARM: pxa: PXA_ESERIES depends on FB_W100.
  ARM: 6605/1: Add missing include "asm/memory.h"
  ARM: 6540/1: Stop irqsoff trace on return to user
  ARM: 6537/1: update Nomadik, U300 and Ux500 maintainers
  ARM: 6536/1: Add missing SZ_{32,64,128}
  ARM: fix cache-feroceon-l2 after stack based kmap_atomic()
  ARM: fix cache-xsc3l2 after stack based kmap_atomic()
  ARM: get rid of kmap_high_l1_vipt()
  ARM: smp: avoid incrementing mm_users on CPU startup
  ARM: pxa: PXA_ESERIES depends on FB_W100.

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=25702Reported-by: NMartin Ettl <ettl.martin@gmx.de>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If security_filter_rule_init() doesn't return a rule, then not everything
is as fine as the return code implies.

This bug only occurs when the LSM (eg. SELinux) is disabled at runtime.

Adding an empty LSM rule causes ima_match_rules() to always succeed,
ignoring any remaining rules.

 default IMA TCB policy:
  # PROC_SUPER_MAGIC
  dont_measure fsmagic=0x9fa0
  # SYSFS_MAGIC
  dont_measure fsmagic=0x62656572
  # DEBUGFS_MAGIC
  dont_measure fsmagic=0x64626720
  # TMPFS_MAGIC
  dont_measure fsmagic=0x01021994
  # SECURITYFS_MAGIC
  dont_measure fsmagic=0x73636673

  < LSM specific rule >
  dont_measure obj_type=var_log_t

  measure func=BPRM_CHECK
  measure func=FILE_MMAP mask=MAY_EXEC
  measure func=FILE_CHECK mask=MAY_READ uid=0

Thus without the patch, with the boot parameters 'tcb selinux=0', adding
the above 'dont_measure obj_type=var_log_t' rule to the default IMA TCB
measurement policy, would result in nothing being measured.  The patch
prevents the default TCB policy from being replaced.
Signed-off-by: NMimi Zohar <zohar@us.ibm.com>
Cc: James Morris <jmorris@namei.org>
Acked-by: NSerge Hallyn <serge.hallyn@canonical.com>
Cc: David Safford <safford@watson.ibm.com>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

commit bf9ae538
(llc: use dev_hard_header) removed the
skb_reset_mac_header call from llc_mac_hdr_init.

This seems fine itself, but br_send_bpdu() invokes ebtables LOCAL_OUT.

We oops in ebt_basic_match() because it assumes eth_hdr(skb) returns
a meaningful result.

Cc: acme@ghostprotocols.net
References: https://bugzilla.kernel.org/show_bug.cgi?id=24532Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf: Fix callchain hit bad cast on ascii display
  arch/x86/oprofile/op_model_amd.c: Perform initialisation on a single CPU
  watchdog: Improve initialisation error message and documentation

* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] em28xx: radio_fops should also use unlocked_ioctl
  [media] wm8775: Revert changeset fcb97573 to avoid a regression
  [media] cx25840: Prevent device probe failure due to volume control ERANGE error

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/djbw/async_tx:
  dmaengine: provide dummy functions for DMA_ENGINE=n
  mv_xor: fix race in tasklet function

The function can't be __init itself (being called from some sysfs
handler), and hence none of the functions it calls can be either.
Signed-off-by: NJan Beulich <jbeulich@novell.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

use pskb_may_pull to access ipv6 header correctly for paged skbs
It was omitted in the bridge code leading to crash in blind
__skb_pull

since the skb is cloned undonditionally we also simplify the
the exit path

this fixes bug https://bugzilla.kernel.org/show_bug.cgi?id=25202

Dec 15 14:36:40 User-PC hostapd: wlan0: STA 00:15:00:60:5d:34 IEEE 802.11: authenticated
Dec 15 14:36:40 User-PC hostapd: wlan0: STA 00:15:00:60:5d:34 IEEE 802.11: associated (aid 2)
Dec 15 14:36:40 User-PC hostapd: wlan0: STA 00:15:00:60:5d:34 RADIUS: starting accounting session 4D0608A3-00000005
Dec 15 14:36:41 User-PC kernel: [175576.120287] ------------[ cut here ]------------
Dec 15 14:36:41 User-PC kernel: [175576.120452] kernel BUG at include/linux/skbuff.h:1178!
Dec 15 14:36:41 User-PC kernel: [175576.120609] invalid opcode: 0000 [#1] SMP
Dec 15 14:36:41 User-PC kernel: [175576.120749] last sysfs file: /sys/devices/pci0000:00/0000:00:1f.2/host0/target0:0:0/0:0:0:0/block/sda/uevent
Dec 15 14:36:41 User-PC kernel: [175576.121035] Modules linked in: approvals binfmt_misc bridge stp llc parport_pc ppdev arc4 iwlagn snd_hda_codec_realtek iwlcore i915 snd_hda_intel mac80211 joydev snd_hda_codec snd_hwdep snd_pcm snd_seq_midi drm_kms_helper snd_rawmidi drm snd_seq_midi_event snd_seq snd_timer snd_seq_device cfg80211 eeepc_wmi usbhid psmouse intel_agp i2c_algo_bit intel_gtt uvcvideo agpgart videodev sparse_keymap snd shpchp v4l1_compat lp hid video serio_raw soundcore output snd_page_alloc ahci libahci atl1c
Dec 15 14:36:41 User-PC kernel: [175576.122712]
Dec 15 14:36:41 User-PC kernel: [175576.122769] Pid: 0, comm: kworker/0:0 Tainted: G        W   2.6.37-rc5-wl+ #3 1015PE/1016P
Dec 15 14:36:41 User-PC kernel: [175576.123012] EIP: 0060:[<f83edd65>] EFLAGS: 00010283 CPU: 1
Dec 15 14:36:41 User-PC kernel: [175576.123193] EIP is at br_multicast_rcv+0xc95/0xe1c [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.123362] EAX: 0000001c EBX: f5626318 ECX: 00000000 EDX: 00000000
Dec 15 14:36:41 User-PC kernel: [175576.123550] ESI: ec512262 EDI: f5626180 EBP: f60b5ca0 ESP: f60b5bd8
Dec 15 14:36:41 User-PC kernel: [175576.123737]  DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
Dec 15 14:36:41 User-PC kernel: [175576.123902] Process kworker/0:0 (pid: 0, ti=f60b4000 task=f60a8000 task.ti=f60b0000)
Dec 15 14:36:41 User-PC kernel: [175576.124137] Stack:
Dec 15 14:36:41 User-PC kernel: [175576.124181]  ec556500 f6d06800 f60b5be8 c01087d8 ec512262 00000030 00000024 f5626180
Dec 15 14:36:41 User-PC kernel: [175576.124181]  f572c200 ef463440 f5626300 3affffff f6d06dd0 e60766a4 000000c4 f6d06860
Dec 15 14:36:41 User-PC kernel: [175576.124181]  ffffffff ec55652c 00000001 f6d06844 f60b5c64 c0138264 c016e451 c013e47d
Dec 15 14:36:41 User-PC kernel: [175576.124181] Call Trace:
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c01087d8>] ? sched_clock+0x8/0x10
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c0138264>] ? enqueue_entity+0x174/0x440
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c016e451>] ? sched_clock_cpu+0x131/0x190
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c013e47d>] ? select_task_rq_fair+0x2ad/0x730
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c0524fc1>] ? nf_iterate+0x71/0x90
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f83e4914>] ? br_handle_frame_finish+0x184/0x220 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f83e4790>] ? br_handle_frame_finish+0x0/0x220 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f83e46e9>] ? br_handle_frame+0x189/0x230 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f83e4790>] ? br_handle_frame_finish+0x0/0x220 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f83e4560>] ? br_handle_frame+0x0/0x230 [bridge]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c04ff026>] ? __netif_receive_skb+0x1b6/0x5b0
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c04f7a30>] ? skb_copy_bits+0x110/0x210
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c0503a7f>] ? netif_receive_skb+0x6f/0x80
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f82cb74c>] ? ieee80211_deliver_skb+0x8c/0x1a0 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f82cc836>] ? ieee80211_rx_handlers+0xeb6/0x1aa0 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c04ff1f0>] ? __netif_receive_skb+0x380/0x5b0
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c016e242>] ? sched_clock_local+0xb2/0x190
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c012b688>] ? default_spin_lock_flags+0x8/0x10
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c05d83df>] ? _raw_spin_lock_irqsave+0x2f/0x50
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f82cd621>] ? ieee80211_prepare_and_rx_handle+0x201/0xa90 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f82ce154>] ? ieee80211_rx+0x2a4/0x830 [mac80211]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f815a8d6>] ? iwl_update_stats+0xa6/0x2a0 [iwlcore]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f8499212>] ? iwlagn_rx_reply_rx+0x292/0x3b0 [iwlagn]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c05d83df>] ? _raw_spin_lock_irqsave+0x2f/0x50
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f8483697>] ? iwl_rx_handle+0xe7/0x350 [iwlagn]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<f8486ab7>] ? iwl_irq_tasklet+0xf7/0x5c0 [iwlagn]
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c01aece1>] ? __rcu_process_callbacks+0x201/0x2d0
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c0150d05>] ? tasklet_action+0xc5/0x100
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c0150a07>] ? __do_softirq+0x97/0x1d0
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c05d910c>] ? nmi_stack_correct+0x2f/0x34
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c0150970>] ? __do_softirq+0x0/0x1d0
Dec 15 14:36:41 User-PC kernel: [175576.124181]  <IRQ>
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c01508f5>] ? irq_exit+0x65/0x70
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c05df062>] ? do_IRQ+0x52/0xc0
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c01036b0>] ? common_interrupt+0x30/0x38
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c03a1fc2>] ? intel_idle+0xc2/0x160
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c04daebb>] ? cpuidle_idle_call+0x6b/0x100
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c0101dea>] ? cpu_idle+0x8a/0xf0
Dec 15 14:36:41 User-PC kernel: [175576.124181]  [<c05d2702>] ? start_secondary+0x1e8/0x1ee

Cc: David Miller <davem@davemloft.net>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 3f5a2a71 zeroes out the statistics
message block (SMB) and coalescing message block (CMB) when adapter ring
resources are freed.  This is desirable behavior, but, as a side effect,
the commit leads to an oops when atl1_set_ringparam() attempts to alter
the number of rx or tx elements in the ring buffer (by using ethtool
-G, for example).  We don't want SMB or CMB to change during this
operation.

Modify atl1_set_ringparam() to preserve SMB and CMB when changing ring
parameters.

Cc: stable@kernel.org
Signed-off-by: NJay Cliburn <jcliburn@gmail.com>
Reported-by: NTõnu Raitviir <jussuf@linux.ee>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge branch 'perf/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/frederic/random-tracing into perf/urgent

Before this patch, the following error would sometimes occur after a
resume on pxa3xx:

    /path/to/mm/memory.c:144: bad pmd 8040542e.

The problem was that a temporary page table mapping was being improperly
restored.

The PXA3xx resume code creates a temporary mapping of resume_turn_on_mmu
to avoid a prefetch abort.  The pxa3xx_resume_after_mmu code requires
that the r1 register holding the address of this mapping not be
modified, however, resume_turn_on_mmu does modify it. It is mostly
correct in that r1 receives the base table address, but it may also
get other bits in 13:0.  This results in pxa3xx_resume_after_mmu
restoring the original mapping to the wrong place, corrupting memory
and leaving the temporary mapping in place.
Signed-off-by: NMatt Reimer <mreimer@sdgsystems.com>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

The commit 6ac6b817 (ARM: pxa: encode
IRQ number into .nr_irqs) removed definition of ITE_LAST_IRQ which
caused the following build error:

CC      arch/arm/common/it8152.o
arch/arm/common/it8152.c: In function 'it8152_init_irq':
arch/arm/common/it8152.c:86: error: 'IT8152_LAST_IRQ' undeclared (first use in this function)
arch/arm/common/it8152.c:86: error: (Each undeclared identifier is reported only once
arch/arm/common/it8152.c:86: error: for each function it appears in.)
make[2]: *** [arch/arm/common/it8152.o] Error 1

Defining the IT8152_LAST_IRQ in the arch/arm/include/hardware/it8152.c
fixes the build.
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

As arch/arm/mach-pxa/eseries.c references w100fb_gpio_{read,write}()
directly.
Signed-off-by: NLennert Buytenhek <buytenh@secretlab.ca>
Signed-off-by: NEric Miao <eric.y.miao@gmail.com>

ipchain__fprintf_graph() casts the number of hits in a branch as an
int, which means we lose its highests bits.

This results in meaningless number of callchain hits in perf.data
that have a high number of hits recorded, typically those that have
callchain branches hits appearing more than INT_MAX. This happens
easily as those are pondered by the event period.
Reported-by: NNick Piggin <npiggin@kernel.dk>
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>

Disable preemption in init_ibs(). The function only checks the
ibs capabilities and sets up pci devices (if necessary). It runs
only on one cpu but operates with the local APIC and some MSRs,
thus it is better to disable preemption.

[    7.034377] BUG: using smp_processor_id() in preemptible [00000000] code: modprobe/483
[    7.034385] caller is setup_APIC_eilvt+0x155/0x180
[    7.034389] Pid: 483, comm: modprobe Not tainted 2.6.37-rc1-20101110+ #1
[    7.034392] Call Trace:
[    7.034400]  [<ffffffff812a2b72>] debug_smp_processor_id+0xd2/0xf0
[    7.034404]  [<ffffffff8101e985>] setup_APIC_eilvt+0x155/0x180
[ ... ]

Addresses https://bugzilla.kernel.org/show_bug.cgi?id=22812

Reported-by: <atswartz@gmail.com>
Signed-off-by: NRobert Richter <robert.richter@amd.com>
Cc: oprofile-list@lists.sourceforge.net <oprofile-list@lists.sourceforge.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Dan Carpenter <error27@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>         [2.6.37.x]
LKML-Reference: <20110103111514.GM4739@erda.amd.com>
[ small cleanups ]
Signed-off-by: NIngo Molnar <mingo@elte.hu>

em28xx uses core assisted locking, so it shouldn't use .ioctl.
The .ioctl callback was replaced by .unlocked_ioctl for video nodes,
but not for radio nodes. This is now corrected.
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

It seems that cx88 and ivtv use wm8775 on some different modes. The
patch that added support for a board with wm8775 broke ivtv boards with
this device. As we're too close to release 2.6.37, let's just revert
it.
Reported-by: NAndy Walls <awalls@md.metrocast.net>
Reported-by: NEric Sharkey <eric@lisaneric.org>
Reported-by: NAuric <auric@aanet.com.au>
Reported by: David Gesswein <djg@pdp8online.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes a regression that crept into 2.6.36.

The volume control scale in the cx25840 driver has an unusual mapping
from register values to v4l2 volume control values.  Enforce the mapping
limits, so that the default volume control setting does not fall out of
bounds to prevent the cx25840 module device probe from failing.
Signed-off-by: NAndy Walls <awalls@md.metrocast.net>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This lets drivers, optionally using the dmaengine, build with DMA_ENGINE
unselected.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

use mv_xor_slot_cleanup() instead of __mv_xor_slot_cleanup() as the former function
aquires the spin lock that needed to protect the drivers data.

Cc: <stable@kernel.org>
Signed-off-by: NSaeed Bishara <saeed@marvell.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>

This patch fixes below build error by adding the missing asm/memory.h,
which is needed for arch_is_coherent().

$ make pxa3xx_defconfig; make
  CC      init/do_mounts_rd.o
In file included from include/linux/list_bl.h:5,
                 from include/linux/rculist_bl.h:7,
                 from include/linux/dcache.h:7,
                 from include/linux/fs.h:381,
                 from init/do_mounts_rd.c:3:
include/linux/bit_spinlock.h: In function 'bit_spin_unlock':
include/linux/bit_spinlock.h:61: error: implicit declaration of function 'arch_is_coherent'
make[1]: *** [init/do_mounts_rd.o] Error 1
make: *** [init] Error 2
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NPeter Huewe <peterhuewe@gmx.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The error message 'NMI watchdog failed to create perf event...'
does not make it clear that this is a fatal error for the
watchdog.  It also currently prints the error value as a
pointer, rather than extracting the error code with PTR_ERR().
Fix that.

Add a note to the description of the 'nowatchdog' kernel
parameter to associate it with this message.
Reported-by: NCesare Leonardi <celeonar@gmail.com>
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: 599368@bugs.debian.org
Cc: 608138@bugs.debian.org
Cc: Don Zickus <dzickus@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: <stable@kernel.org> # .37.x and later
LKML-Reference: <1294009362.3167.126.camel@localhost>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

The owner field was removed from struct attribute in
6fd69dc5, so don't assign it anymore.
Signed-off-by: NMaurus Cuelenaere <mcuelenaere@gmail.com>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>

* 'kvm-updates/2.6.37' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: i8259: initialize isr_ack
  KVM: MMU: Fix incorrect direct gfn for unpaged mode shadow

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
  ALSA: hda: Use LPIB quirk for Dell Inspiron m101z/1120
  sound: Prevent buffer overflow in OSS load_mixer_volumes
  ASoC: codecs: wm8753: Fix register cache incoherency
  ASoC: codecs: wm9090: Fix register cache incoherency
  ASoC: codecs: wm8962: Fix register cache incoherency
  ASoC: codecs: wm8955: Fix register cache incoherency
  ASoC: codecs: wm8904: Fix register cache incoherency
  ASoC: codecs: wm8741: Fix register cache incoherency
  ASoC: codecs: wm8523: Fix register cache incoherency
  ASoC: codecs: max98088: Fix register cache incoherency
  ASoC: codecs: Add missing control_type initialization

* 'rc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6:
  kconfig: fix undesirable side effect of adding "visible" menu attribute

isr_ack is never initialized.  So, until the first PIC reset, interrupts
may fail to be injected.  This can cause Windows XP to fail to boot, as
reported in the fallout from the fix to
https://bugzilla.kernel.org/show_bug.cgi?id=21962.
Reported-and-tested-by: NNicolas Prochazka <prochazka.nicolas@gmail.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>

The earlier call to atm_dev_lookup increases the reference count of dev,
so decrease it on the way out.

The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
expression x, E;
constant C;
@@

x = atm_dev_lookup(...);
... when != false x != NULL
    when != true x == NULL
    when != \(E = x\|x = E\)
    when != atm_dev_put(dev);
*return -C;
// </smpl>
Signed-off-by: NJulia Lawall <julia@diku.dk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 56543af9 "starfire: use BUILD_BUG_ON for netdrv_addr_t" revealed
that the preprocessor condition used to find the size of dma_addr_t
yielded the wrong result for some architectures and configurations.
This was kluged for 64-bit PowerPC in commit 3e502e63 by adding yet
another case to the condition.  However, 64-bit MIPS configurations
are not detected reliably either.

This should be fixed by using CONFIG_ARCH_DMA_ADDR_T_64BIT, but that
isn't yet defined everywhere it should be.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Besides -ETIMEDOUT and -EINTR, pci_read_vpd may return other error
values like -ENODEV or -EINVAL which are ignored due to the buggy
check, but the data are not read from VPD anyway and this is checked
subsequently with at most 3 needless loop iterations. This does not
show up as a runtime bug.

CC: Matt Carlson <mcarlson@broadcom.com>
CC: Michael Chan <mchan@broadcom.com>
Signed-off-by: NDavid Sterba <dsterba@suse.cz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>