Removed "ctrl |= DXEPCTL_USBACTEP" from
dwc2_hsotg_start_req() function because this
step is done in dwc2_hsotg_ep_enable().
Tested-by: NJohn Keeping <john@metanate.com>
Signed-off-by: NVardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add a check in dwc2_hsotg_ep_sethalt() so that it does not halt
isochronous endpoints.
Signed-off-by: NVahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The gadget API function usb_ep_set_halt() expects the gadget to return
-EAGAIN if the ep is active. Add support for this behavior.

Otherwise this may break mass storage protocol if a STALL is attempted
on the endpoint.
Signed-off-by: NVahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

In host slave mode, the core asserts the rxready, txfifoempty interrupts
that get serviced in the gadget irq handler. Prevent servicing of these
when not in the gadget mode of operation.
Signed-off-by: NVardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Replaced the WARN_ON with a check and return of -EINVAL in the
dwc2_hsotg_ep_enable function if ep0 is passed in.
Signed-off-by: NVahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The host/device mode set with dr_mode should be kept all the time,
not being changed to OTG in gadget setup (by overriding CFGUSB_FORCEDEVMODE
and CFGUSB_FORCEHOSTMODE bits).
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NPrzemek Rudy <prudy1@o2.pl>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Move the register save and restore functions into the host and gadget
specific files.
Tested-by: NDouglas Anderson <dianders@chromium.org>
Reviewed-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@kernel.org>

The "enumspd" field is located in register DSTS[2:1], but the code
which checks the bitfield does not shift the value accordingly. This
in turn causes incorrect detection of gadget link partner speed in
dwc2_hsotg_irq_enumdone() .

Shift the value accordingly to fix the problem with speed detection.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMarek Vasut <marex@denx.de>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: John Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove call to dwc2_hsotg_init() from dwc2_gadget_init(). The
gadget_init function should not access any device registers because the
mode isn't guaranteed here.

Also, this is already called elsewhere before anything starts on the
gadget so it is not necessary here.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The dwc2_core_reset() function exists in the core so use that one
instead.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use the previously cached hw params in the gadget. This saves a reset
and force mode in the gadget initialization during probe and makes
getting the hardware parameters consistent between gadget and host.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When receiving GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF interrupt,
DCTL will be overwritten with DCTL_CGOUTNAK or DCTL_CGNPINNAK values.
Instead of overwriting it, write only needed bits.

It could cause an issue if GINTSTS_GINNAKEFF or GINTSTS_GOUTNAKEFF
interrupt is received after dwc2 disabled pullup by writing
DCTL_SFTDISCON bit.
Pullup will then be re-enabled whereas it should not.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To stop an out endpoint, software should set sets the Global OUT NAK,
but not the Global Non-periodic IN NAK. This driver bug leads the out-ep
failed be in disabled state with below error.

dwc2_hsotg_ep_stop_xfr: timeout DOEPCTL.EPDisable
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NDu, Changbin <changbin.du@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

DWC2 module on some platforms needs three additional hardware
resources: phy controller, clock and power supply. All of them must be
enabled/activated to properly initialize and operate. This was initially
handled in s3c-hsotg driver, which has been converted to 'gadget' part
of dwc2 driver. Unfortunately, not all of this code got moved to common
platform code, what resulted in accessing DWC2 registers without
enabling low-level hardware resources. This fails for example on Exynos
SoCs. This patch moves all the code for managing those resources to
common platform.c file and provides convenient wrappers for controlling
them.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

init_mutex is a leftover from the time, when s3c-hsotg driver did not
implement proper pull up/down control and emulated it by enabling
enabling/disabling usb phy. Proper pull up/down control has been added
by commit 5b9451f8 ("usb: dwc2: gadget:
use soft-disconnect udc feature in pullup() method"), so init_muxtex can
be removed now to avoid potential deadlocks with other locks.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

USB OTG driver in isochronous mode has to set the parity of the receiving
microframe. The parity is set to even by default. This causes problems for
an audio gadget, if the host starts transmitting on odd microframes.

This fix uses Incomplete Periodic Transfer interrupt to toggle between
even and odd parity until the Transfer Complete interrupt is received.
Signed-off-by: NRoman Bacik <rbacik@broadcom.com>
Reviewed-by: NAbhinav Ratna <aratna@broadcom.com>
Reviewed-by: NSrinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: NScott Branden <sbranden@broadcom.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During typical gadget operation, dwc2 clock was enabled 3 times: from
dwc2_gadget_init(), dwc2_hsotg_udc_start() and dwc2_hsotg_pullup(), and
then disabled in s3c_hsotg_pullup(), s3c_hsotg_udc_stop() and
dwc2_hsotg_remove(). This really makes no sense, so leave clock control
code only in dwc2_gadget_init/remove functions.
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch removes doubled call to dwc2_hsotg_of_probe() function.
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When dwc2_hsotg_handle_unaligned_buf_complete() hs_req->req.buf
already destroyed, in dwc2_hsotg_unmap_dma(), it touches
hs_req->req.dma again, so dwc2_hsotg_unmap_dma() should be called
before dwc2_hsotg_handle_unaligned_buf_complete(). Otherwise, it
will cause a bad_page BUG, when allocate this memory page next
time.

This bug led to the following crash:

BUG: Bad page state in process swapper/0  pfn:2bdbc
[   26.820440] page:eed76780 count:0 mapcount:0 mapping:  (null) index:0x0
[   26.854710] page flags: 0x200(arch_1)
[   26.885836] page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
[   26.919179] bad because of flags:
[   26.948917] page flags: 0x200(arch_1)
[   26.979100] Modules linked in:
[   27.008401] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W3.14.0 #17
[   27.041816] [<c010e1f8>] (unwind_backtrace) from [<c010a704>] (show_stack+0x20/0x24)
[   27.076108] [<c010a704>] (show_stack) from [<c087eea8>] (dump_stack+0x70/0x8c)
[   27.110246] [<c087eea8>] (dump_stack) from [<c01ce0b8>] (bad_page+0xfc/0x12c)
[   27.143958] [<c01ce0b8>] (bad_page) from [<c01ce65c>] (get_page_from_freelist+0x3e4/0x50c)
[   27.179298] [<c01ce65c>] (get_page_from_freelist) from [<c01ce9a0>] (__alloc_pages_nodemask)
[   27.216296] [<c01ce9a0>] (__alloc_pages_nodemask) from [<c01cf00c>] (__get_free_pages+0x20/)
[   27.252326] [<c01cf00c>] (__get_free_pages) from [<c01e5bec>] (kmalloc_order_trace+0x34/0xa)
[   27.288295] [<c01e5bec>] (kmalloc_order_trace) from [<c0203304>] (__kmalloc+0x40/0x1ac)
[   27.323751] [<c0203304>] (__kmalloc) from [<c052abc0>] (dwc2_hsotg_ep_queue.isra.12+0x7c/0x1)
[   27.359937] [<c052abc0>] (dwc2_hsotg_ep_queue.isra.12) from [<c052af88>] (dwc2_hsotg_ep_queue)
[   27.397478] [<c052af88>] (dwc2_hsotg_ep_queue_lock) from [<c0554110>] (rx_submit+0xfc/0x164)
[   27.433619] [<c0554110>] (rx_submit) from [<c05546e8>] (rx_complete+0x22c/0x230)
[   27.468872] [<c05546e8>] (rx_complete) from [<c052b528>] (dwc2_hsotg_complete_request+0xfc/0)
[   27.506240] [<c052b528>] (dwc2_hsotg_complete_request) from [<c052bba0>] (dwc2_hsotg_handle_o)
[   27.545401] [<c052bba0>] (dwc2_hsotg_handle_outdone) from [<c052be70>] (dwc2_hsotg_epint+0x2c)
[   27.583689] [<c052be70>] (dwc2_hsotg_epint) from [<c052c750>] (dwc2_hsotg_irq+0x1dc/0x4ac)
[   27.621041] [<c052c750>] (dwc2_hsotg_irq) from [<c01682e0>] (handle_irq_event_percpu+0x70/0x)
[   27.659066] [<c01682e0>] (handle_irq_event_percpu) from [<c01684ec>] (handle_irq_event+0x4c)
[   27.697322] [<c01684ec>] (handle_irq_event) from [<c016bae0>] (handle_fasteoi_irq+0xc8/0x11)
[   27.735451] [<c016bae0>] (handle_fasteoi_irq) from [<c0167b8c>] (generic_handle_irq+0x30/0x)
[   27.773918] [<c0167b8c>] (generic_handle_irq) from [<c0167ca4>] (__handle_domain_irq+0x84/0)
[   27.812018] [<c0167ca4>] (__handle_domain_irq) from [<c01003b0>] (gic_handle_irq+0x48/0x6c)
[   27.849695] [<c01003b0>] (gic_handle_irq) from [<c010b340>] (__irq_svc+0x40/0x50)
[   27.886907] Exception stack(0xc0d01ee0 to 0xc0d01f28)
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NJeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: NYunzhi Li <lyz@rock-chips.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If system is loaded, reset, enum-done and setup interrupts can occur
at the same time. Current interrupt handling sequence will handle
setup packet's interrupt before handling reset interrupt. Which will
break the enumeration process. Correct sequence is to handle reset,
enum-done and then any other endpoint interrupts.
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When disconnecting cable, controller will detect a suspend condition
and enter partial power down. If vbus_session is called by the phy
driver during hibernation, make sure controller exit hibernation
before it is accessed.
Signed-off-by: NJianqiang Tang <jianqiang.tang@intel.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

idstschng interrupt should not be used when id pin control is
external. This is already handled on dwc2 host part. Fix it on gadget
part as well.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There is a 200ms guard period to avoid unnecessary resets of the dwc2
ip. This delay sometimes prove to be too large when usbcv is run with
an ehci host. dwc2 only needs to be reset after addressed state.
Change the logic to reset ip after addressed state.
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Make sure there are no requests pending on ep0 before reinitializing
core. Otherwise, dwc2_hsotg_enqueue_setup will fail afterwards.

Also, take hsotg->lock before calling
dwc2_hsotg_core_init_disconnected() from dwc2_conn_id_status_change()
as dwc2_hsotg_complete_request() expect lock to be held.
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If the request being dequeued is already started, disable endpoint
to stop the transfer and then call dwc2_hsotg_complete_request().
Endpoint will be re-enabled on next call to dwc2_hsotg_start_req().
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

wIndex field was missing. Also print in natural order instead of
Req first, so that its easier to compare for example against
bus analyzer logs.
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

dwc2_hsotg_start_req starts a request only if endpoint is not stalled.
Ignore this check for ep0 as core will clear DOEPCTL0.Stall after
sending stall handshake. Prepare instead for receiving next setup
packet.
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

No point of continue with initialization if core is not in a sane
state.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some device may have external id pin control enabled, so op_state
will not be set on id pin interrupt change.
Thus, ensure op_state is set to peripheral during vbus detection.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Modifying the pullup state during host mode trig a new enumeration
of attached device. Thus, avoid modifying pullup in host mode.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

ID status change interrupt will not be handled in peripheral only
configuration. So initialize op_state during gadget init.
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Correctly update lx_state on gadget connection and disconnection.
When usb cable is disconnected, lx_state must be updated to L3 as
controller could be in power off state.
When usb cable is connected, lx_state must be updated to L0 as
controller is powered.
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: NRobert Baldyga <r.baldyga@samsung.com>
Tested-by: NDinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.

This patch is necessary to access dwc2 registers correctly on big-endian
systems such as the mips based SoCs made by Lantiq. Then dwc2 can be
used to replace ifx-hcd driver for Lantiq platforms found e.g. in
OpenWrt.

The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h

Some files were then hand-edited to fix checkpatch.pl warnings about
too long lines.
Signed-off-by: NAntti Seppälä <a.seppala@gmail.com>
Signed-off-by: NVincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Convert endpoint configuration to new capabilities model.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It's just a lot clearer to use | operator instead of
+ operator.

Caught by coccicheck:

	"
	drivers/usb/dwc2/gadget.c:2883:26-27: WARNING: sum of probable
	bitmasks, consider |
	"

Cc: John Youn <John.Youn@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As dwc2 pci module is now exporting dwc2 platform device, include
platform.o in dwc2-y and remove USB_DWC2_PLATFORM configuration
option. Driver will be built as two modules, dwc2.ko and dwc2_pci.ko.
dwc2.ko is the new platform driver.

Remove all EXPORT_SYMBOL_GPL as they are not needed any more.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Force argument is not used anymore. Clean up leftovers from
https://lkml.org/lkml/2014/12/9/283Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Inform that device is otg-capable in case of otg configuration.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

During vbus session, usb controller needs to exit hibernation if it was
previously in suspend state.
Since controller will be resetted and configured, there is no need
to restore registers.

Moreover, set lx_state to L0 on B session. vbus_session callback may
not be used by all platforms. Thus, controller software state needs
to be set to L0 if the controller detects a valid B session.
Otherwise, lx_state will remain L2 and prevent any request submission.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>