Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switch name is emitted in the kernel log, so having the right name
there is nice.

Fixes: 1558727a ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6141")
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When registering an MDIO bus, it is possible to pass an array of
interrupts, one per address on the bus. phylib will then associate the
interrupt to the PHY device, if no other interrupt is provided.

Some of the global2 interrupts are PHY interrupts. Place them into the
MDIO bus structure.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add to the info structure the number of internal PHYs, if they generate
interrupts. Some of the older generations of switches have internal
PHYs, but no interrupt registers. In this case, set the count to zero.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the recent change to polling for interrupts, it is important that
the number of global 1 interrupts is listed. Without it, the driver
requests an interrupt domain for zero interrupts, which returns
EINVAL, and the probe fails.

Add two missing entries.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can hit the register lock not held assertion with the following path:

[   34.170631] mv88e6085 0.1:00: Switch registers lock not held!
[   34.176510] CPU: 0 PID: 950 Comm: ethtool Not tainted 4.16.0-rc4 #143
[   34.182985] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[   34.189519] Backtrace:
[   34.192033] [<8010c4b4>] (dump_backtrace) from [<8010c788>] (show_stack+0x20/0x24)
[   34.199680]  r6:9f5dc010 r5:00000011 r4:9f5dc010 r3:00000000
[   34.205434] [<8010c768>] (show_stack) from [<80679d38>] (dump_stack+0x24/0x28)
[   34.212719] [<80679d14>] (dump_stack) from [<804844a8>] (mv88e6xxx_read+0x70/0x7c)
[   34.220376] [<80484438>] (mv88e6xxx_read) from [<804870dc>] (mv88e6xxx_port_get_cmode+0x34/0x4c)
[   34.229257]  r5:a09cd128 r4:9ee31d07
[   34.232880] [<804870a8>] (mv88e6xxx_port_get_cmode) from [<80487e6c>] (mv88e6352_port_has_serdes+0x24/0x64)
[   34.242690]  r4:9f5dc010
[   34.245309] [<80487e48>] (mv88e6352_port_has_serdes) from [<804880b8>] (mv88e6352_serdes_get_stats+0x28/0x12c)
[   34.255389]  r4:00000001
[   34.257973] [<80488090>] (mv88e6352_serdes_get_stats) from [<804811e8>] (mv88e6xxx_get_ethtool_stats+0xb0/0xc0)
[   34.268156]  r10:00000000 r9:00000000 r8:00000000 r7:a09cd020 r6:00000001 r5:9f5dc01c
[   34.276052]  r4:9f5dc010
[   34.278631] [<80481138>] (mv88e6xxx_get_ethtool_stats) from [<8064f740>] (dsa_slave_get_ethtool_stats+0xbc/0xc4)

mv88e6xxx_get_ethtool_stats() calls mv88e6xxx_get_stats() which calls both
chip->info->ops->stats_get_stats(), which holds the register lock, and
chip->info->ops->serdes_get_stats() which does not. Have
chip->info->ops->serdes_get_stats() be running with the register lock held to
avoid such assertions.

Fixes: 436fe17d ("net: dsa: mv88e6xxx: Allow the SERDES interfaces to have statistics")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle polled interrupts correctly when loading the module.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Fixes: 294d711e ("net: dsa: mv88e6xxx: Poll when no interrupt defined")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Call the common irq free function, rather than going recursive and
blowing away the stack, followed by the machine.

Fixes: 294d711e ("net: dsa: mv88e6xxx: Poll when no interrupt defined")
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for reading the SERDES statistics of the mv88e8352, using
the standard ethtool -S option. The SERDES interface can be mapped to
either port 4 or 5, so only return statistics on those ports, if the
SERDES interface is in use.

The counters are reset on read, so need to be accumulated. Add a per
port structure to hold the stats counters. The 6352 only has a single
SERDES interface and so only one port will using the newly added
array. However the 6390 family has as many SERDES interfaces as ports,
each with statistics counters. Also, PTP has a number of counters per
port which will also need accumulating.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When gettting the number of statistics, the strings and the actual
statistics, call the SERDES ops if implemented. This means the stats
code needs to return the number of strings/stats they have placed into
the data, so that the SERDES strings/stats can follow on.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now, there has been no need to hold the reg mutex while getting
the count of statistics, or the strings, because the hardware was not
accessed. When adding support for SERDES statistics, it is necessary
to access the hardware, to determine if a port is using the SERDES
interface. So add mutex lock/unlocks.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By passing the port, we allow different ports to have different
statistics. This is useful since some ports have SERDES interfaces
with their own statistic counters.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all boards have the interrupt output from the switch connected to
a GPIO line. In such cases, phylib has to poll the internal PHYs,
rather than receive an interrupt when there is a change in the link
state. phylib polls once per second, and per PHY reads around 4
words. With a switch typically having 4 internal PHYs, this means 16
MDIO transactions per second.

Rather than performing this phylib level polling, have the driver poll
the interrupt status register. If the status register indicates an
interrupt condition processing of interrupts in the same way as if a
GPIO was used.

Polling 10 times a second places less load on the MDIO bus. But rather
than taking on average 0.5s to detect a link change, it takes less
than 0.05s. Additionally, other interrupts, such as the watchdog, ATU
and VTU violations will be reported.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MV88E6352 and later switches support GPIO control through the "Scratch
& Misc" global2 register. Two of the pins controlled this way on the
mv88e6390 family are the external MDIO pins. They can either by used
as part of the MII interface for port 0, GPIOs, or MDIO. Add a
function to configure them for MDIO, if possible, and call it when
registering the external MDIO bus.
Suggested-by: NRussell King <rmk@armlinux.org.uk>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PTP code needs low latency access to the PTP hardware timestamps.
Reading all the ATU entries in one go adds a lot of latency to the PTP
code. So take and release the reg_lock mutex for each individual MAC
address in the ATU, allowing the PTP thread jump in between.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The PTP code needs low latency access to the PTP hardware timestamps.
Reading all the statistics in one go adds a lot of latency to the PTP
code. So take and release the reg_lock mutex for each individual
statistics, allowing the PTP thread jump in between.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements RX/TX timestamping support.

The Marvell PTP hardware supports RX timestamping individual message
types, but for simplicity we only support the EVENT receive filter since
few if any clients bother with the more specific filter types.

checkpatch and reverse Christmas tree changes by Andrew Lunn.

Re-factor duplicated code paths and avoid IfOk anti-pattern, use the
common ptp worker thread from the class layer and time stamp UDP/IPv4
frames as well as Layer-2 frame by Richard Cochran.
Signed-off-by: NBrandon Streiff <brandon.streiff@ni.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MV88E6352 and later switches support GPIO control through the "Scratch
& Misc" global2 register. (Older switches do too, though with a slightly
different register interface. Only the 6352-style is implemented here.)

Add a new file, global2_scratch.c, for operations in the Scratch & Misc
space. Additionally, add a GPIO operations structure to present an
abstract view over GPIO manipulation.

Reverse Christmas tree and unsigned has been replaced with unsigned
int by Andrew Lunn.
Signed-off-by: NBrandon Streiff <brandon.streiff@ni.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds basic support for exposing the 32-bit timestamp counter
inside the mv88e6xxx switch as a ptp_clock.

Adjfine implemented by Richard Cochran.
Andrew Lunn: fix return value of PTP stub function.
Signed-off-by: NBrandon Streiff <brandon.streiff@ni.com>
Signed-off-by: NRichard Cochran <richardcochran@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements support for accessing the Precision Time Protocol
and Time Application Interface registers via the AVB register interface
in the Global 2 register.

The register interface differs slightly between different models; older
models use a 3-bit operations field, while newer models use a 2-bit
field. The operations values and the special "global port" values are
different between the two. This is a similar split to the differences
in the "Ingress Rate" register between models, so, like in that case,
we call the two variants "6352" and "6390" and create an ops structure
to abstract between the two.

checkpatch fixups by Andrew Lunn
Signed-off-by: NBrandon Streiff <brandon.streiff@ni.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We only register the ATU and VTU irq when we have a chip level IRQ.
In the error path, we should only attempt to remove the ATU and VTU
irq if we also have a chip level IRQ.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is a problem with the VTU, an interrupt can be
generated. Trap this interrupt and decode the registers to determine
what the problem was, then log the error.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When there is a problem with the ATU, an interrupt can be
generated. Trap this interrupt and decode the registers to determine
what the problem was, then log the error.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce a configuration option: CONFIG_NET_DSA_LEGACY allowing to compile out
support for the old platform device and Device Tree binding registration.
Support for these configurations is scheduled to be removed in 4.17.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The MDIO busses need to be unregistered before they are freed,
otherwise BUG() is called. Add a call to the unregister code if the
registration fails, since we can have multiple busses, of which some
may correctly register before one fails. This requires moving the code
around a little.

Fixes: a3c53be5 ("net: dsa: mv88e6xxx: Support multiple MDIO busses")
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When removing the interrupt handling code, we should mask the
generation of interrupts. The code however unmasked all
interrupts. This can then cause a new interrupt. We then get into a
deadlock where the interrupt thread is waiting to run, and the code
continues, trying to remove the interrupt handler, which means waiting
for the thread to complete. On a UP machine this deadlocks.

Fix so we really mask interrupts in the hardware. The same error is
made in the error path when install the interrupt handling code.

Fixes: 3460a577 ("net: dsa: mv88e6xxx: Mask g1 interrupts and free interrupt")
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current dsa_upstream_port() helper still assumes a unique CPU port
in the whole switch fabric. This is becoming wrong, as every port in the
fabric has its dedicated CPU port, thus every port has an upstream port.

Add a port argument to the dsa_upstream_port() helper and fetch its CPU
port instead of the deprecated unique fabric CPU port. A CPU or unused
port has no dedicated CPU port, so return itself in this case.

At the same time, change the return value from u8 to unsigned int since
there is no need to limit the size here.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move the setup of the global upstream port within the
mv88e6xxx_setup_upstream_port function.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper function to setup the upstream port of a given port.

This is the port used to reach the dedicated CPU port. This function
will be extended later to setup the global upstream port as well.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mv88e6xxx driver currently assumes a single CPU port in the fabric
and thus floods frames with unknown DA on a single DSA port, the one
that is one hop closer to the CPU port.

With multiple CPU ports in mind, this isn't true anymore because CPU
ports could be found behind both DSA ports of a device in-between
others.

For example in a A <-> B <-> C fabric, both A and C having CPU ports,
device B will have to flood such frame to its two DSA ports.

This patch considers both CPU and DSA ports of a device as upstream
ports, where to flood frames with unknown DA addresses.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DSA switch MDB ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.

Remove the trans argument from MDB prepare and add operations.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DSA switch VLAN ops pass the switchdev_trans structure down to the
drivers, but no one is using them and they aren't supposed to anyway.

Remove the trans argument from VLAN prepare and add operations.

At the same time, fix the following checkpatch warning:

    WARNING: line over 80 characters
    #74: FILE: drivers/net/dsa/dsa_loop.c:177:
    +				      const struct switchdev_obj_port_vlan *vlan)
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A number of drivers want to check whether the configured CPU port is a
possible configuration for enabling tagging, pass down the CPU port
number so they verify that.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The statistics histogram mode was not being explicitly initialized on
devices other than the 6390 family. Clearing the statistics then
overwrote the default setting, setting the histogram to a reserved
mode.

Explicitly set the histogram mode for all devices. Change the
statistics clear into a read/modify/write, and since it is now more
complex, move it into global1.c.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

By default, the switch does not flood broadcast frames. Instead the
broadcast address is unknown in the ATU, so the frame gets forwarded
out the cpu port. The software bridge then floods it back to the
individual switch ports which are members of the bridge.

Add an ATU entry in the switch so that it floods broadcast frames out
ports, rather than have the software bridge do it. Also, send a copy
out the cpu port and any dsa ports. Rely on the port vectors to
prevent broadcast frames leaking between bridges, and separated ports.

Additionally, when a VLAN is added, a new FID is allocated.  This
represents a new table of ATU entries. A broadcast entry is added to
the new FID.

With offload_fwd_mark being set, the software bridge will not flood
the frames it receives back to the switch.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This function is going to be needed by a soon to be added new
function. Move it earlier so we can avoid a forward declaration.
No functional changes.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When testing if a VLAN is one more than one bridge, we print an error
message that the VLAN is already in use somewhere else. Print both the
new port which would like the VLAN, and the port which already has it,
to aid debugging.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Having the same VLAN on multiple bridges is currently unsupported as
an offload. mv88e6xxx_port_check_hw_vlan() is used to ensure that a
VLAN is not on multiple bridges when adding a VLAN range to a port. It
loops the ports and checks to see if there are ports in a different
bridge with the same VLAN.

While walking all switch ports, the code was checking if the new port
has a netdev slave attached to it. If not, skip checking the port
being walked. This seems like a typ0. If the new port does not have a
slave, how has a VLAN been added to it in the first place, requiring
this check be performed at all? More likely, we should be checking if
the port being walked has a slave. Without the port having a slave, it
cannot have a VLAN on it, so there is no need to check further for
that particular port.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch renames dsa_is_normal_port to dsa_is_user_port because "user"
is the correct term in the DSA terminology, not "normal".
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The unused ports are currently configured in normal mode. This does not
prevent the switch from being functional, but it is unnecessary. Skip
unused ports.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>