This changes the respective line in /proc/interrupts from

 49:          x          x  mv88e6xxx-g1   7 Edge      mv88e6xxx-g1

to

 49:          x          x  mv88e6xxx-g1   7 Edge      mv88e6xxx-g2

which makes more sense.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The switch name is emitted in the kernel log, so having the right name
there is nice.

Fixes: 1558727a ("net: dsa: mv88e6xxx: Add support for ethernet switch 88E6141")
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a new ACL group is created its region (ACL) list is initially
empty. Thus, the call to mlxsw_sp_acl_tcam_group_update() would
basically invalidate an already invalid (non-existent) group.

Remove the unnecessary call and make the function symmetric to its del()
counterpart.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver currently creates empty ACL groups, binds them to the
requested port and then fills them with actual ACLs that point to TCAM
regions.

However, empty ACL groups are considered invalid and upcoming firmware
versions are going to forbid their binding.

Work around this limitation by only performing the binding after the
first ACL was added to the group.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to set some of the fields within 'mbox_config_profile',
since they are reserved and capability mask should be set to zero.
Signed-off-by: NTal Bar <talb@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the opcodes don't use in, out or both mboxes. In such cases, the
mbox address is a reserved field and FW expects it to be zero.
Signed-off-by: NShalom Toledo <shalomt@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mlx5 driver calls ida_pre_get() in a loop for no readily apparent
reason.  The driver uses ida_simple_get() which will call ida_pre_get()
by itself and there's no need to use ida_pre_get() unless using
ida_get_new().
Signed-off-by: NMatthew Wilcox <mawilcox@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes the polling mechanism of GLGEN_RSTAT.DEVSTATE in the
PF Reset path when Global Reset is in progress. While the driver
is polling for the end of the PF Reset and the Global Reset is
triggered, abandon the PF Reset path and prepare for the
upcoming Global Reset.
Signed-off-by: NPaweł Jabłoński <pawel.jablonski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

These flags were defined, but there is no use within the driver code, so
we don't need to keep them.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Setting link settings on backplane devices shouldn't be allowed.
This patch adds one more device id to the list which we check
that against.
Signed-off-by: NPatryk Małek <patryk.malek@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix return types from i40e_status to enum i40e_status_code.
Signed-off-by: NDoug Dziggel <douglas.a.dziggel@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

A recent patch updated the signature for i40e_aq_set_switch_config() to
add a new parameter 'mode'. It forgot to document the parameter in the
doxygen function header comment. Add the parameter to the function
description now.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

During suspend client MSIx vectors are freed while they are still
in use causing a crash on entering S3.

Fix this calling client close before freeing up its MSIx vectors.
Also update the client MSIx vectors on resume before client
open is called.

Fixes commit b980c063 ("i40e: shutdown all IRQs and disable MSI-X
when suspended")
Reported-by: NStefan Assmann <sassmann@redhat.com>
Signed-off-by: NShiraz Saleem <shiraz.saleem@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Setting link settings on backplane devices shouldn't be allowed.
This patch adds one more device id to the list which we check
that against.
Signed-off-by: NPatryk Małek <patryk.malek@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e_set_link_ksettings and i40e_get_link_ksettings use different
codepaths to check available and supported advertisement modes. This
creates scenarios where it's possible to set a mode that's not allowed,
resulting in a link down.

Fix setting advertisement in i40e_set_link_ksettings by calling
i40e_get_link_ksettings to check what modes are allowed.
Signed-off-by: NJan Sokolowski <jan.sokolowski@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

While doing some code review I noticed that we can get into a state where
we exit with the "IN_CRITICAL_TASK" bit set while notifying the PF of
flower filters. This patch is meant to address that plus tweak the ordering
of the while loop waiting on it slightly so that we don't wait an extra
period after we have failed for the last time.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When registering an MDIO bus, it is possible to pass an array of
interrupts, one per address on the bus. phylib will then associate the
interrupt to the PHY device, if no other interrupt is provided.

Some of the global2 interrupts are PHY interrupts. Place them into the
MDIO bus structure.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add to the info structure the number of internal PHYs, if they generate
interrupts. Some of the older generations of switches have internal
PHYs, but no interrupt registers. In this case, set the count to zero.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With the recent change to polling for interrupts, it is important that
the number of global 1 interrupts is listed. Without it, the driver
requests an interrupt domain for zero interrupts, which returns
EINVAL, and the probe fails.

Add two missing entries.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We can hit the register lock not held assertion with the following path:

[   34.170631] mv88e6085 0.1:00: Switch registers lock not held!
[   34.176510] CPU: 0 PID: 950 Comm: ethtool Not tainted 4.16.0-rc4 #143
[   34.182985] Hardware name: Freescale Vybrid VF5xx/VF6xx (Device Tree)
[   34.189519] Backtrace:
[   34.192033] [<8010c4b4>] (dump_backtrace) from [<8010c788>] (show_stack+0x20/0x24)
[   34.199680]  r6:9f5dc010 r5:00000011 r4:9f5dc010 r3:00000000
[   34.205434] [<8010c768>] (show_stack) from [<80679d38>] (dump_stack+0x24/0x28)
[   34.212719] [<80679d14>] (dump_stack) from [<804844a8>] (mv88e6xxx_read+0x70/0x7c)
[   34.220376] [<80484438>] (mv88e6xxx_read) from [<804870dc>] (mv88e6xxx_port_get_cmode+0x34/0x4c)
[   34.229257]  r5:a09cd128 r4:9ee31d07
[   34.232880] [<804870a8>] (mv88e6xxx_port_get_cmode) from [<80487e6c>] (mv88e6352_port_has_serdes+0x24/0x64)
[   34.242690]  r4:9f5dc010
[   34.245309] [<80487e48>] (mv88e6352_port_has_serdes) from [<804880b8>] (mv88e6352_serdes_get_stats+0x28/0x12c)
[   34.255389]  r4:00000001
[   34.257973] [<80488090>] (mv88e6352_serdes_get_stats) from [<804811e8>] (mv88e6xxx_get_ethtool_stats+0xb0/0xc0)
[   34.268156]  r10:00000000 r9:00000000 r8:00000000 r7:a09cd020 r6:00000001 r5:9f5dc01c
[   34.276052]  r4:9f5dc010
[   34.278631] [<80481138>] (mv88e6xxx_get_ethtool_stats) from [<8064f740>] (dsa_slave_get_ethtool_stats+0xbc/0xc4)

mv88e6xxx_get_ethtool_stats() calls mv88e6xxx_get_stats() which calls both
chip->info->ops->stats_get_stats(), which holds the register lock, and
chip->info->ops->serdes_get_stats() which does not. Have
chip->info->ops->serdes_get_stats() be running with the register lock held to
avoid such assertions.

Fixes: 436fe17d ("net: dsa: mv88e6xxx: Allow the SERDES interfaces to have statistics")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Handle polled interrupts correctly when loading the module.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Fixes: 294d711e ("net: dsa: mv88e6xxx: Poll when no interrupt defined")
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Finally, remove the TSO-specific fields in the TX pool
strcutures. These are no longer needed with the introduction
of separate buffer pools for TSO transmissions.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update routine that cleans up any outstanding transmits that
have not received completions when the device needs to close.
Introduces a helper function that cleans one TX pool to make
code more readable.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Improve TX pool buffer accounting to prevent the producer
index from overruning the consumer. First, set the next free
index to an invalid value if it is in use. If next buffer
to be consumed is in use, drop the packet.

Finally, if the transmit fails for some other reason, roll
back the consumer index and set the free map entry to its original
value. This should also be done if the DMA map fails.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update TX and TX completion routines to account for TX pool
restructuring. TX routine first chooses the pool depending
on whether a packet is GSO or not, then uses it accordingly.

For the completion routine to know which pool it needs to use,
set the most significant bit of the correlator index to one
if the packet uses the TSO pool. On completion, unset the bit
and use the correlator index to release the buffer pool entry.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce function that initializes one TX pool. Use that to
create each pool entry in both the standard TX pool and TSO
pool arrays.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce function that frees one TX pool.  Use that to release
each pool in both the standard TX pool and TSO pool arrays.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update TX pool reset routine to accommodate new TSO pool array. Introduce
a function that resets one TX pool, and use that function to initialize
each pool in both pool arrays.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove some unused fields in the structure and include values
describing the individual buffer size and number of buffers in
a TX pool. This allows us to use these fields for TX pool buffer
accounting as opposed to using hard coded values. Include a new
pool array for TSO transmissions.
Signed-off-by: NThomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds tracepoints to the driver which has proved useful in
debugging startup and shutdown race conditions.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The caller has a valid pointer, pass it to rndis_filter_halt_device
and avoid any possible RCU races here.
Signed-off-by: NStephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In VLAN_AWARE mode CPSW can insert VLAN header encapsulation word on Host
port 0 egress (RX) before the packet data if RX_VLAN_ENCAP bit is set in
CPSW_CONTROL register. VLAN header encapsulation word has following format:

 HDR_PKT_Priority bits 29-31 - Header Packet VLAN prio (Highest prio: 7)
 HDR_PKT_CFI 	  bits 28 - Header Packet VLAN CFI bit.
 HDR_PKT_Vid 	  bits 27-16 - Header Packet VLAN ID
 PKT_Type         bits 8-9 - Packet Type. Indicates whether the packet is
                 	VLAN-tagged, priority-tagged, or non-tagged.
	00: VLAN-tagged packet
	01: Reserved
	10: Priority-tagged packet
	11: Non-tagged packet

This feature can be used to implement TX VLAN offload in case of
VLAN-tagged packets and to insert VLAN tag in case Non-tagged packet was
received on port with PVID set. As per documentation, CPSW never modifies
packet data on Host egress (RX) and as result, without this feature
enabled, Host port will not be able to receive properly packets which
entered switch non-tagged through external Port with PVID set (when
non-tagged packet forwarded from external Port with PVID set to another
external Port - packet will be VLAN tagged properly).

Implementation details:
- on RX driver will check CPDMA status bit RX_VLAN_ENCAP BIT(19) in CPPI
descriptor to identify when VLAN header encapsulation word is present.
- PKT_Type = 0x01 or 0x02 then ignore VLAN header encapsulation word and
pass packet as is;
- if HDR_PKT_Vid = 0 then ignore VLAN header encapsulation word and pass
packet as is;
- In dual mac mode traffic is separated between ports using default port
vlans, which are not be visible to Host and so should not be reported.
Hence, check for default port vlans in dual mac mode and ignore VLAN header
encapsulation word;
- otherwise fill SKB with VLAN info using __vlan_hwaccel_put_tag();
- PKT_Type = 0x00 (VLAN-tagged) then strip out VLAN header from SKB.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Setting sge_uld_rxq_info to NULL in free_queues_uld().
We are referencing sge_uld_rxq_info in cxgb_up(). This
will fix a panic when interface is brought up after a
ULDq creation failure.

Fixes: 94cdb8bb (cxgb4: Add support for dynamic allocation
       of resources for ULD)
Signed-off-by: NArjun Vynipadath <arjun@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudhar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1) Moved interrupt enable related code from octeon_process_droq_poll_cmd()
   to separate function octeon_enable_irq().
2) Removed wrapper function octeon_process_droq_poll_cmd(), and directlyi
   using octeon_droq_process_poll_pkts().
3) Removed unused macros POLL_EVENT_XXX.
Signed-off-by: NIntiyaz Basha <intiyaz.basha@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

notify uld drivers if the adapter encounters fatal
error.
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This optional binding (as described in the ethernet DT bindings doc)
directs the netdev to the phydev to use. This is useful for a phy
chip that has >1 phy in it, and two netdevs are using the same phy
chip (i.e. the second mac's phy lives on the first mac's MDIO bus)

The devicetree snippet would look something like this:

ethernet@feedf00d {
	...
	phy-handle = <&phy0> // the first netdev is physically wired to phy0
	...
	phy0: phy@0 {
		...
		reg = <0x0> // MDIO address 0
		...
	}
	phy1: phy@1 {
		...
		reg = <0x1> // MDIO address 1
		...
	}
...
}

ethernet@deadbeef {
	...
	phy-handle = <&phy1> // tells the driver to use phy1 on the
						 // first mac's mdio bus (it's wired thusly)
	...
}

The work done to add the phy_node in the first place (dacdbb4d:
"net: macb: add fixed-link node support") will consume the
device_node (if found).
Signed-off-by: NBrad Mouring <brad.mouring@ni.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In phy_device's general probe, this device will already be set for
phy register polling, rendering this code redundant.
Signed-off-by: NBrad Mouring <brad.mouring@ni.com>
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The macb mii setup (mii_probe() and mii_init()) previously was
somewhat interspersed, likely a result of organic growth and hacking.

This change moves mii bus registration into mii_init and probing the
bus for devices into mii_probe.
Signed-off-by: NBrad Mouring <brad.mouring@ni.com>
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d1179094 ("enic: Add vxlan offload support for IPv6 pkts")
added vxlan offload support for IPv6 pkts. Required change in
enic_udp_tunnel_del was not made. This creates a bug where once user
adds IPv6 tunnel, hw offload for that cannot be deleted.

This patch removes check for IP proto in tunnel delete path. Driver need
not check for IP proto since same UDP port cannot be used to create two
tunnels.

Fixes: d1179094 ("enic: Add vxlan offload support for IPv6 pkts")
Signed-off-by: NGovindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>