Skip to content

K
Kernel

openeuler / Kernel
接近 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 19 6月, 2015 1 次提交
  3. 17 6月, 2015 1 次提交
  5. 13 6月, 2015 1 次提交
  7. 12 6月, 2015 2 次提交
    • D
      iommu/vt-d: Only enable extended context tables if PASID is supported · c83b2f20
      由 David Woodhouse 提交于 
      Although the extended tables are theoretically a completely orthogonal
feature to PASID and anything else that *uses* the newly-available bits,
some of the early hardware has problems even when all we do is enable
them and use only the same bits that were in the old context tables.

For now, there's no motivation to support extended tables unless we're
going to use PASID support to do SVM. So just don't use them unless
PASID support is advertised too. Also add a command-line bailout just in
case later chips also have issues.

The equivalent problem for PASID support has already been fixed with the
upcoming VT-d spec update and commit bd00c606 ("iommu/vt-d: Change
PASID support to bit 40 of Extended Capability Register"), because the
problematic platforms use the old definition of the PASID-capable bit,
which is now marked as reserved and meaningless.

So with this change, we'll magically start using ECS again only when we
see the new hardware advertising "hey, we have PASID support and we
actually tested it this time" on bit 40.

The VT-d hardware architect has promised that we are not going to have
any reason to support ECS *without* PASID any time soon, and he'll make
sure he checks with us before changing that.

In the future, if hypothetical new features also use new bits in the
context tables and can be seen on implementations *without* PASID support,
we might need to add their feature bits to the ecs_enabled() macro.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
      c83b2f20
    • J
      ARM: dts: zx: add an initial zx296702 dts and doc · d5553cb0
      由 Jun Nie 提交于 
      Add initial dts file and document for ZX296702 and board ZX296702-AD1.
More peripherals will be added later.
Signed-off-by: NJun Nie <jun.nie@linaro.org>
Signed-off-by: NKevin Hilman <khilman@linaro.org>
      d5553cb0
  9. 06 6月, 2015 1 次提交
  11. 31 5月, 2015 2 次提交
  13. 30 5月, 2015 2 次提交
  15. 26 5月, 2015 1 次提交
  17. 23 5月, 2015 1 次提交
  19. 21 5月, 2015 1 次提交
    • S
      ARM: vf610: enable Cortex-M4 configuration on Vybrid SoC · 8064887e
      由 Stefan Agner 提交于 
      This patch allows to build the Kernel for Vybrid (VF6xx) SoC
when ARMv7-M CPU is selected. The resulting image runs on the
secondary Cortex-M4 core. This core has equally access to all
peripherals as the main Cortex-A5 core. However, there is no
resource control mechanism, hence when both cores are used
simultaneously, orthogonal device tree's are required.

The boot CPU is dependent on the SoC variant. The available
boards use mostly variants where the Cortex-A5 is the primary
and hence the boot CPU. Booting the secondary Cortex-M4 CPU
needs SoC specific registers written. There is no in kernel
support for this right now, a external userspace utility
called "m4boot" can be used to boot the kernel:

m4boot xipImage initramfs.cpio.lzo vf610m4-colibri.dtb
Signed-off-by: NStefan Agner <stefan@agner.ch>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
      8064887e
  21. 20 5月, 2015 1 次提交
  23. 18 5月, 2015 1 次提交
  25. 16 5月, 2015 2 次提交
  27. 11 5月, 2015 2 次提交
    • X
      KVM: MMU: fix SMAP virtualization · 0be0226f
      由 Xiao Guangrong 提交于 
      KVM may turn a user page to a kernel page when kernel writes a readonly
user page if CR0.WP = 1. This shadow page entry will be reused after
SMAP is enabled so that kernel is allowed to access this user page

Fix it by setting SMAP && !CR0.WP into shadow page's role and reset mmu
once CR4.SMAP is updated
Signed-off-by: NXiao Guangrong <guangrong.xiao@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NPaolo Bonzini <pbonzini@redhat.com>
      0be0226f
    • P
      pty: Fix input race when closing · 1a48632f
      由 Peter Hurley 提交于 
      A read() from a pty master may mistakenly indicate EOF (errno == -EIO)
after the pty slave has closed, even though input data remains to be read.
For example,

       pty slave       |        input worker        |    pty master
                       |                            |
                       |                            |   n_tty_read()
pty_write()            |                            |     input avail? no
  add data             |                            |     sleep
  schedule worker  --->|                            |     .
                       |---> flush_to_ldisc()       |     .
pty_close()            |       fill read buffer     |     .
  wait for worker      |       wakeup reader    --->|     .
                       |       read buffer full?    |---> input avail ? yes
                       |<---   yes - exit worker    |     copy 4096 bytes to user
  TTY_OTHER_CLOSED <---|                            |<--- kick worker
                       |                            |

		                **** New read() before worker starts ****

                       |                            |   n_tty_read()
                       |                            |     input avail? no
                       |                            |     TTY_OTHER_CLOSED? yes
                       |                            |     return -EIO

Several conditions are required to trigger this race:
1. the ldisc read buffer must become full so the input worker exits
2. the read() count parameter must be >= 4096 so the ldisc read buffer
   is empty
3. the subsequent read() occurs before the kicked worker has processed
   more input

However, the underlying cause of the race is that data is pipelined, while
tty state is not; ie., data already written by the pty slave end is not
yet visible to the pty master end, but state changes by the pty slave end
are visible to the pty master end immediately.

Pipeline the TTY_OTHER_CLOSED state through input worker to the reader.
1. Introduce TTY_OTHER_DONE which is set by the input worker when
   TTY_OTHER_CLOSED is set and either the input buffers are flushed or
   input processing has completed. Readers/polls are woken when
   TTY_OTHER_DONE is set.
2. Reader/poll checks TTY_OTHER_DONE instead of TTY_OTHER_CLOSED.
3. A new input worker is started from pty_close() after setting
   TTY_OTHER_CLOSED, which ensures the TTY_OTHER_DONE state will be
   set if the last input worker is already finished (or just about to
   exit).

Remove tty_flush_to_ldisc(); no in-tree callers.

Fixes: 52bce7f8 ("pty, n_tty: Simplify input processing on final close")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=96311
BugLink: http://bugs.launchpad.net/bugs/1429756
Cc: <stable@vger.kernel.org> # 3.19+
Reported-by: NAndy Whitcroft <apw@canonical.com>
Reported-by: NH.J. Lu <hjl.tools@gmail.com>
Signed-off-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
      1a48632f
  29. 09 5月, 2015 1 次提交
  31. 06 5月, 2015 3 次提交
  33. 05 5月, 2015 1 次提交
    • S
      bus: omap_l3_noc: Fix master id address decoding for OMAP5 · e7309c26
      由 Suman Anna 提交于 
      The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:

  1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
     11 bits on OMAP5 as against 8 bits on OMAP4, with the master
     NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
     field.
  2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
     input sources on OMAP5. The common DEBUGSS source is at a
     different input on each SoC.

Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.
Signed-off-by: NSuman Anna <s-anna@ti.com>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
      e7309c26
  35. 04 5月, 2015 2 次提交
  37. 03 5月, 2015 1 次提交
    • A
      target/user: Disallow full passthrough (pass_level=0) · 8ee83a74
      由 Andy Grover 提交于 
      TCMU requires more work to correctly handle both user handlers that want
all SCSI commands (pass_level=0) for a se_device, and also handlers that
just want I/O commands and let the others be emulated by the kernel
(pass_level=1). Only support the latter for now.

For full passthrough, we will need to support a second se_subsystem_api
template, due to configfs attributes being different between the two modes.
Thus pass_level is extraneous, and we can remove it.

The ABI break for TCMU v2 is already applied for this release, so it's
best to do this now to avoid another ABI break in the future.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>
      8ee83a74
  39. 01 5月, 2015 2 次提交
  41. 30 4月, 2015 1 次提交
    • M
      Revert "powerpc/tm: Abort syscalls in active transactions" · 68fc378c
      由 Michael Ellerman 提交于 
      This reverts commit feba4036.

Although the principle of this change is good, the implementation has a
few issues.

Firstly we can sometimes fail to abort a syscall because r12 may have
been clobbered by C code if we went down the virtual CPU accounting
path, or if syscall tracing was enabled.

Secondly we have decided that it is safer to abort the syscall even
earlier in the syscall entry path, so that we avoid the syscall tracing
path when we are transactional.

So that we have time to thoroughly test those changes we have decided to
revert this for this merge window and will merge the fixed version in
the next window.

NB. Rather than reverting the selftest we just drop tm-syscall from
TEST_PROGS so that it's not run by default.

Fixes: feba4036 ("powerpc/tm: Abort syscalls in active transactions")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
      68fc378c
  43. 28 4月, 2015 1 次提交
  45. 27 4月, 2015 3 次提交
  47. 23 4月, 2015 2 次提交
  49. 22 4月, 2015 1 次提交
  51. 21 4月, 2015 2 次提交
  53. 20 4月, 2015 1 次提交