Don't overwrite SPD setting during hard reset.  This change has the
(intended) side effect of honoring the BIOS configuration.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

When ata_set_mode() fails on a device, make ata_set_mode() return
error code and pointer to the device instead of disabling it directly.
This gives more control to higher level driving logic.

This patch does not change the end result (configured transfer mode)
although it may make libata repeat mode configuration to the peer of a
failing device.  Later ata_bus_probe() rewrite will make full use of
this change.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Merge ata_host_set_pio() and ata_host_set_dma() into ata_set_mode()
and use function-level *dev to iterate over devices.  This eases
soon-to-follow ata_set_mode() interface change.

While at it, kill an unnecessary comment and normalize others.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make ata_set_mode() return without doing anything if there is no
device on the port.  This is in preparation for ata_bus_probe()
changes.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch renames ata_dev_present() to ata_dev_enabled() and adds
ata_dev_disabled().  This is to discern the state where a device is
present but disabled from not-present state.  This disctinction is
necessary when configuring transfer mode because device selection
timing must not be violated even if a device fails to configure.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make do_probe_reset() generic by pushing classification check into
ata_drive_probe_reset() and rename it to ata_do_reset().  This will be
used by EH reset.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Separate out ata_spd_string() from sata_print_link_status().  This
will be used by SATA spd configuration routines.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_bus_probe() uses unsigned int rc to receive negative errno and
returns the converted unsigned int value.  Convert temporary variables
to int and make ata_bus_probe() return negative errno on failure.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make ata_set_mode() return correct error value when ata_dev_set_mode()
fails.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_xfer_tbl is terminated by entry with -1 as ->shift.  However,
->shift was unsigned int making the termination condition bogus.  This
patch converts ->shift and ->bits to int.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

There is no reason for the issuer to diddle with a failed qc as the
issuer has complete control over when a qc gets freed (usually in
->complete_fn).  Make ata_qc_issue() responsible for completing qcs
which failed to issue.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

On sg_err failure path, ata_qc_issue() doesn't mark the qc active
before returning.  This triggers WARN_ON() in __ata_qc_complete() when
the qc gets completed.  This patch moves ap->active_tag and
QCFLAG_ACTIVE setting to the top of the function.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_dev_init_params() fixes:
- Get the "heads" and "sectors" parameters from caller instead of implicitly from dev->id[].
- Return AC_ERR_INVALID instead of 0 if an invalid parameter is found
Signed-off-by: NAlbert Lee <albertcc@tw.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>

Last of the set, just clean up some oddments. Assuming the whole set is
now ok then the remaining differences are the setup of PIO_0 at reset
and the ->data_xfer method.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add a field to the host_set called 'flags' (was host_set_flags changed
to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel
Add a ->mode_filter() hook to allow drivers to filter modes
Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core

This provides the needed framework to support all the mode rules found
in the PATA world. The simplex filter deals with 'to spec' simplex DMA
systems found in older chips. The cable filter avoids duplicating the
same rules in each chip driver with PATA. Finally the mode filter is
neccessary because drive/chip combinations have errata that forbid
certain modes with some drives or types of ATA object.

Drive speed setup remains per channel for now and the filters now use
the framework Tejun put into place which cleans them up a lot from the
older libata-pata patches.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

I think this is still needed with the new probe code (which btw seems to
be missing docs in upstream ?).
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Some hardware doesn't want the usual mode setup logic running. This
allows the hardware driver to replace it for special cases in the least
invasive way possible.
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Kill trailing whitespace.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add FIXME above ata_dev_xfermask noting that the current
implementation limits all transfer modes to the fastest of the slowest
device on a port which isn't necessary.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

ata_bus_softreset() should return AC_ERR_* on failure not arbitrary
positive number.  While at it, reformat comment above it.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Acked-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

E.D.D. has no user in-tree and mostly useless.  Kill it.  For possible
out-of-tree users, add a nice warning message and error handling if
LLDD doesn't report any useable reset mechanism (and thus tries to use
E.D.D.).
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Remove some of the dependence on the host_set struct
in preparation for supporting SAS HBAs. Adds a struct device
pointer to the ata_port struct.
Signed-off-by: NBrian King <brking@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Mostly, trim trailing whitespace.

Also:
* export ata_dev_pair
* move ata_dev_classify export closer to ata_dev_pair export

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

At the moment libata doesn't pass pm_message_t down ata_device_suspend.
This causes drives to be powered down when we just want a freeze,
causing unnecessary wear and tear. This patch gets pm_message_t passed
down so that it can be used to determine whether to power down the
drive.
Signed-off-by: NNigel Cunningham <nigel@suspend2.net>

 drivers/scsi/libata-core.c |    5 +++--
 drivers/scsi/libata-scsi.c |    4 ++--
 drivers/scsi/scsi_sysfs.c  |    2 +-
 include/linux/libata.h     |    4 ++--
 include/scsi/scsi_host.h   |    2 +-
 5 files changed, 9 insertions(+), 8 deletions(-)
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make ata_set_mode() responsible for determining whether to take port
or device offline on failure.  ata_dev_set_xfermode() and
ata_dev_set_mode() indicate error to the caller instead of disabling
port directly on failure.  Also, for consistency, ata_dev_present()
check is done in ata_set_mode() instead of ata_dev_set_mode().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

We may or may not disable a device after ata_dev_configure() fails.
Kill 'not supported, ignoring' message in ata_dev_configure() and use
ata_dev_disable() in ata_bus_probe().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch implements ata_dev_disable() which prints a warning message
and takes @dev offline.  Currently, this is done by explicitly
incrementing dev->class with case-by-case warning messages.  Giving
user clear indication when libata gives up will be more important as
libata will be doing more retries.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

libata core is being changed to disallow port/device disable on lower
layers.  However, some LLDDs (sata_mv) directly disable port on
command failure.  This patch makes ata_exec_internal() check whether a
port got disabled after an internal command.  If it is, AC_ERR_SYSTEM
is added to err_mask and the port gets re-enabled.

As internal command failure results in device disable for drivers
which don't implement newer reset/EH callbacks, this change results in
no behavior change for single device per port controllers.  For
slave-possible LLDDs which disable port on command failure, (1) such
drivers don't exist currently, (2) issuing command to the other device
of once-disabled port shouldn't result in catastrophe even if such
driver exists.  So, this should be enough as a temporary measure.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Now that each ata_device has xfer masks, per-dev limits can be made
per-dev instead of per-port.  Make per-dev limits per-dev.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add per-dev pio/mwdma/udma_mask.  All transfer mode limits used to be
applied to ap->*_mask which unnecessarily restricted other devices
sharing the port.  This change will also benefit later EH speed down
and hotplug.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Implement ata_unpack_xfermask().
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

No code changes, just moving code between files.

As libata now can do PIO, don't ignore PIO-only devices.
Signed-off-by: NTejun Heo <htejun@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Not much to say here except that some drives have fixed and bad firmware
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The current code follows the spec but uses an overlong delay. This would
be great if the hardware did. Several vendors however forget the D7
pulldown. Fortunately 0xFF isnt a sane reset state so we can use it to
skip detection as is done in drivers/ide. (ie this is a tested solution
over a long time)
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Alan noted: "bmdma may be zero but the bmdma_irq_clear function gets
called even in this case during pure PIO operation. Check we have a
bmdma before we use it."

I fixed this by adding a check for zero.  While was I there, I fixed the
non-standard indentation of the small function's code.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>