The code for performing the calculation was only in the SH-4 probe
path, move it out to the common path so the other parts get this
right too.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

These ended up causing too many problems on older parts,
revert for now..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Previously this was using a hardcoded 32, use L1_CACHE_BYTES for
cacheline alignment instead.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

When I run a preemptive kernel-2.6.20 for SH7780, a created
kthread(pdflush) can not exit by do_exit() in kernel_thread_helper. I
think that the created kthread should have a room for 'struct pt_regs'
space on the stack top, because __switch_to() will refer to the space as
follows using 'regs = task_pt_regs(prev)' and next condition may be true.
Signed-off-by: NHideo Saito <saito@densan.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There was a missing return in do_signal() that caused the saved
sigmask to be written back after having successfully delivered
the signal.
Signed-off-by: NRyusuke Sakato <sakato@hsdv.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This takes care of tearing down the UBC so it's not inadvertently
left configured at the next context switch time. Failure to do
this results in spurious SIGTRAPs in certain debug sequences.
Signed-off-by: NStuart Menefy <stuart.menefy@st.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The C99 specification states in section 6.11.5:

The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NAdrian Bunk <bunk@stusta.de>

This tidies up some of the rts7751r2d mess and gets it booting
again. Update the defconfig, too.
Signed-off-by: NMasayuki Hosokawa <hosokawa@ace-jp.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This ended up causing problems for older parts (particularly ones
using PTEA). Revert this for now, it can be added back in once it's
had some more testing.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We accidentally broke the inotify syscalls, fix those up again.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Rename the existing flush routines to local_ variants for use by
the IPI-backed global flush routines on SMP.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There are a lot of bogus cpu_data-> references that only end up working
for the boot CPU, convert these to current_cpu_data to fixup SMP.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Previously this was implemented using a global cache, cache
this per-CPU instead and bump up the number of context IDs to
match NR_CPUS.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch does the following:
- remove the make_ipr_irq stuff from dma-sh.c and replace it
  with a simple channel<->irq mapping table.
- add DMTEx_IRQ constants for sh4 cpus
- fix sh7751 DMAE irq number

The SH7780 uses the same IRQs for DMA as other SH4 types, so
I put the constants on top of the dma.h file.

Other CPU types need to #define their own DMTEx_IRQ contants
in their appropriate header.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add SH7760 IPR IRQ data; makes 2.6.20-rc bootable again.
Signed-off-by: NManuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

handle_BUG() uses TRAPA_BUG_OPCODE which is only defined for
CONFIG_BUG, make sure it's not built when CONFIG_BUG=n.
Signed-off-by: NNobuhiro Iwamatsu <hemamu@t-base.ne.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This converts the lazy dcache handling to the model described in
Documentation/cachetlb.txt and drops the ptep_get_and_clear() hacks
used for the aliasing dcaches on SH-4 and SH7705 in 32kB mode. As a
bonus, this slightly cuts down on the cache flushing frequency.

With that and the PTEA handling out of the way, the update_mmu_cache()
implementations can be consolidated, and we no longer have to worry
about which configuration the cache is in for the SH7705 case.

And finally, explicitly disable the lazy writeback on SMP (SH-4A).
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

There were a few more things that needed fixing up, namely THREAD_SIZE
and the TLB miss handler where certain PTRS_PER_PGD == PTRS_PER_PTE
assumptions were being made.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This fixes up shmin (and SH7706/SH7708) IPR support for some of the
recent API changes.
Signed-off-by: NTakashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This allows the baud rate for earlyprintk for sh4 without the
standard BIOS to be set via the command line. This uses the same
format as i386 and x86_64, which is:

	earlyprintk=serial,ttySC1,38400

The second parameter (ttySC1 above) is usually the console device
name or the io address of the serial port. I allow that to be
specified but ignore it in order to keep the format the same as
i386/x86_64.
Signed-off-by: NJamie Lenehan <lenehan@twibble.org>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

IPR initialize proceduere update.
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This rips out most of the needlessly complicated sh_bios and kgdb
trap handling, and forces it all through a common fast dispatch path.
As more debug traps are inserted, it's important to keep them in sync
for all of the parts, not just SH-3/4.

As the SH-2 parts are unable to do traps in the >= 0x40 range, we
restrict the debug traps to the 0x30-0x3f range on all parts, and
also bump the kgdb breakpoint trap down in to this range (from 0xff
to 0x3c) so it's possible to use for nommu.

Optionally, this table can be padded out to catch spurious traps for
SH-3/4, but we don't do that yet..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

1. Rename saved_command_line into boot_command_line.
2. Set command_line as __initdata.
Signed-off-by: NAlon Bar-Lev <alon.barlev@gmail.com>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use attribute(weak).
Signed-off-by: NAlexey Dobriyan <adobriyan@openvz.org>
Acked-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Update all arch/*/kernel/vmlinux.lds.S to not include space for initramfs
when CONFIG_BLK_DEV_INITRAMFS is not selected.  This saves another 4 kbytes
on most platfoms (some reserve PAGE_SIZE for initramfs).
Signed-off-by: NJean-Paul Saman <jean-paul.saman@nxp.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

This adds in support for the BUG() trap on SH-2.
Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This had a bogus .data.idt reference, fix it up..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Add the SCIF IRQs to the IPR table for SH7722.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This was inadvertently broken when the entry.S code split up,
restore the missing branch and get subsequent traps working
under debug again. This manifested itself as a lockup when
attempting to reload the VBR base.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds CPU support for the SH7722.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

A couple of these were missed.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

SH-2 and SH-2A need to use a different syscall base for the trapa
vector than the other parts, so fixup the logic in the kernel_execve()
case.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Some time ago the schedule frame size changed and we failed to reflect
this in get_wchan() at the time. This first popped up as a problem on
SH7751R where schedule_frame ended up being unaligned and generating
an unaligned trap. This fixes it up again..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Previously we haven't been doing anything with verbose BUG() reporting,
and we've been relying on the oops path for handling BUG()'s, which is
rather sub-optimal.

This switches BUG handling to use a fixed trapa vector (#0x3e) where we
construct a small bug frame post trapa instruction to get the context
right. This also makes it trivial to wire up a DIE_BUG for the atomic
die chain, which we couldn't really do before.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Signed-off-by: NYoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>