Patch is to prevent the OTG host of doing 3 times enumeration of
device when the Host suspends for HNP.  The error code used in
this case is ENOTSUPP.
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix a few serial gadget issues reported by the latest "sparse":
some functions should have been defined as static, not just
declared that way.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

in order to be able to switch back to 'flow-control none'
after having activated 'flow-control rts/cts', I made
a small change to 'pl2303.c'.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the generic driver also had its own buffering.

Signed-off-by: Oliver Neukum <oneukum@suse.de_
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

this fixes the flushing trouble due to its own buffering for this driver.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Cc: Al Borchers <alborchers@steinerpoint.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the new tty buffering code allows usb drivers to stop private buffering.
In fact we must do so to allow flushing to work correctly. This does so
for the visor driver.
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure gadgetfs userspace interface is properly exported:

 - Move <linux/usb_gadgetfs.h> to <linux/usb/gadgetfs.h>;
 - Export it using Kbuild;
 - Add an #include guard;
 - Correct some internal documentation;
 - Update struct layout so it's the same on 32/64 bit kernels.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Substitute USB instances of __attribute__ ((unused)) functions with the
newly introduced __maybe_unused.
Signed-off-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

For MPC831x support, change the ehci-fsl driver to preserve
bits set in platform code.  Add a common CONFIG_USB_EHCI_FSL
to indicate presence of Freescale EHCI SOC.  Add FSL_USB2_DR_OTG
operating mode support, thus both host and device can work for the
mini-ab receptacle.  Note: this doesn't enable OTG protocol
support.
Signed-off-by: NLi Yang <leoli@freescale.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Now select the big-endian configuration options
CONFIG_USB_EHCI_BIG_ENDIAN_MMIO and CONFIG_USB_EHCI_BIG_ENDIAN_DESC in
the usb host Kconfig file and not in the platform Kconfig files.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the AMCC 440EPx EHCI controller whose
in-memory data structures and the registers are represented in big-
endian format.
Signed-off-by: NStefan Roese <sr@denx.de>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The new FT232RL allows setting and getting the value of the latency
timer, like on the FT232BM. However, the driver will not create the
sysfs entries for the RL without this one-line patch. 

I have tested it on two systems with successful results.


From: Stepan Moskovchenko <stevenm86@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as911) replaces some C++-style commented-out debugging
lines in driver.c with a new "verbose debugging" macro.  It makes the
code look cleaner, and it's easier to turn the debugging on or off.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as908) adds central protection in usbcore for the
prototypical race between opening and unregistering a char device.
The spinlock used to protect the minor-numbers array is replaced with
an rwsem, which can remain locked across a call to a driver's open()
method.  This guarantees that open() and deregister() will be mutually
exclusive.

The private locks currently used in several individual drivers for
this purpose are no longer necessary, and the patch removes them.  The
following USB drivers are affected: usblcd, idmouse, auerswald,
legousbtower, sisusbvga/sisusb, ldusb, adutux, iowarrior, and
usb-skeleton.

As a side effect of this change, usb_deregister_dev() must not be
called while holding a lock that is acquired by open().  Unfortunately
a number of drivers do this, but luckily the solution is simple: call
usb_deregister_dev() before acquiring the lock.

In addition to these changes (and their consequent code
simplifications), the patch fixes a use-after-free bug in adutux and a
race between open() and release() in iowarrior.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Okay, found it.  The root cause here was a missing CONFIG_USB_SUSPEND=y,
which means the hci_usb device never got marked as USB_STATE_SUSPENDED,
which then caused the loop to go on forever.

The system works fine now with CONFIG_USB_SUSPEND=y in the .config.

Here's the patch to prevent future lockups for this or other causes.
I no longer need it, but it does still seem a good idea.
Signed-off-by: NMark Lord <mlord@pobox.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Recently, the USB device matching code stopped matching generic interface
matches against devices with vendor-specific device class values.

Some drivers now need to explicitly match USB device ID's (in addition to
generic interface info) to retain the same behaviour as before. This new macro,
suggested by Alan Stern, makes the explicit device/interface matching a little
simpler for those users.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove some dead CONFIG_ symbols, and document the status of a few others.
The "gadget_chips.h" references are by and large to drivers which exist
but haven't yet been submitted for merging to the main 2.6 tree.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Improvements and fixes to the MCT U232 USB/serial interface driver.
Implement RTS/CTS hardware flow control.  Implement HUPCL.  Bring
handling of DTR and RTS into conformance with other Linux serial
port drivers - assert both signals when opening device, even if
"crtscts" is not currently selected.
Signed-off-by: NDave Platt <dplatt@radagast.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch modifies the USB regular 250ms timer to be "perfectly aligned" to
the second and quarters thereof. This change is there to make sure that if
you have multiple USB ports, the timers for all these ports will fire at the
same time rather than all spread out. All spread out wakes the CPU up from
power saving idle a lot more than needed...
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds support for the most recent Digi EdgePort USB serial
devices.
Signed-off-by: NMartin K. Petersen <mkp@mkp.net>
Signed-off-by: NMike Swift <mikes@digi.com>
Signed-off-by: NJeremy McBane <jmcbane@digi.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as898) changes the port reset code in the hub driver.  If
a connect change occurs, it is reported the same way as a disconnect
(which of course is what it really is).

It also changes usb_reset_device(), to prevent the routine from futilely
retrying the reset after a disconnect has occurred.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as895) fixes up a loose end in the port-handover code for
the USB-Persist facility.  A special case occurs when a high-speed
device is attached to a port which the user has designated to run at
full-speed only; the port must be disabled before the handover can
take place.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as888) adds a new USB device quirk for devices which are
unable to resume correctly.  By using the new code added for the
USB-persist facility, it is a simple matter to reset these devices
instead of resuming them.  To get things kicked off, a quirk entry is
added for the Philips PSC805.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as887) changes the way ehci-hcd and ohci-hcd handle a loss
of VBUS power during suspend.  In order for the USB-persist facility
to work correctly, it is necessary for low- and full-speed devices
attached to a high-speed port to be handed back to the companion
controller during resume processing.

This entails three changes: adding code to ehci-hcd to perform the
handover, removing code from ohci-hcd to turn off ports during
root-hub reinit, and adding code to ohci-hcd to turn on ports during
PCI controller resume.  (Other bus glue resume methods for platforms
supporting high-speed controllers would need a similar change, if any
existed.)
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as886) adds the controversial USB-persist facility,
allowing USB devices to persist across a power loss during system
suspend.

The facility is controlled by a new Kconfig option (with appropriate
warnings about the potential dangers); when the option is off the
behavior will remain the same as it is now.  But when the option is
on, people will be able to use suspend-to-disk and keep their USB
filesystems intact -- something particularly valuable for small
machines where the root filesystem is on a USB device!
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add a class which allows for an easier integration with udev.

This code was originally written by Paolo Abeni, and arrived to my tree
as a part of big patch to add binary API on December 18. As I understand,
Paolo always meant the class to be a part of the whole thing. This is his
udev rule to go along with the patch:

KERNEL=="usbmon[0-9]*", NAME="usbmon%n", MODE="0440",OWNER="root",GROUP="bin"
Signed-off-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Last week I've been searching for a driver for the CA-42 cable (see usb
 below) that fitted my kernel 2.6.20. I only found an abandoned version for a
 driver on your website that indeed worked on 2.6.18 but wouldn't even
 compile with a more recent 2.6.20 kernel.

I fiddled 2 evenings with the kernel code and have patched it up now to work
with the modifications in the 2.6.20 kernel. The patch is attached hereafter
and it works fine (at least for me :-) ).

Bus 2 Device 13: ID 0ea0:6858 Ours Technology, Inc.

I had to fiddle a little with the settings in .gnokiirc but that also
 occurred with the older 2.6.18 kernel. Nevertheless, on one system with this
 cable and my Nokia 6070 I had best results with :

model = 6510
connection = dku5

while on an other system with the same kernel, cable and phone it only worked
with :

model = AT
connection = serial
serial_write_usleep = 1


From: Kees Lemmens <C.W.J.Lemmens@ewi.tudelft.nl>
Cc: <pawel.kot@gmail.com>
Cc: <bozo@andrews.hu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove atomic operations on the reference counter for EHCI queue heads.
On various platforms (including ppc7448), atomic operations are unusable
with dma-coherent memory.
Signed-off-by: NSteven J. Hill <sjhill1@rockwellcollins.com>
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu", so that
the user can disable all the options in that menu at once instead of having to
disable each option separately.
Signed-off-by: NJan Engelhardt <jengelh@gmx.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This revised patch (as893c) improves the method used by the hub driver
to release its private data structure.  The current code is non-robust,
relying on a memory region not getting reused by another driver after
it has been freed.  The patch adds a reference count to the structure,
resolving the question of when to release it.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as892) removes the "locktree" routine from the hub driver.
It currently is used in only one place, by a single kernel thread;
hence it isn't doing any good.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This revised patch (as891b) removes two unnecessary references to
intf->dev.power.power_state from usb-storage, and replaces a reference
to root_hub->dev.power.power_state with a check of hcd->state.  This
is in preparation for the removal of dev.power.power_state, which is
already deprecated.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as889) prevents the hub driver from trying to resume a
port when there is a new connection.  For one thing, the resume is not
needed -- the upcoming port reset will clear the suspend feature
automatically.  For another, on some systems the resume fails and
causes problems.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as885) moves the root-hub bus_suspend() and bus_resume()
method calls from the hub driver's suspend and resume methods into the
usb_generic driver methods, where they make just as much sense.

Their old locations were not fully correct.  For example, in a kernel
compiled without CONFIG_USB_SUSPEND, if one were to do:

	echo -n 1-0:1.0 >/sys/bus/usb/drivers/hub/unbind

to unbind the hub driver from a root hub, there would then be no way
to suspend that root hub.  Attempts to put the system to sleep would
fail; the USB controller driver would refuse to suspend because the
root hub was still active.

The patch also makes a very slight change in the way devices with no
driver are handled during suspend.  Rather than doing a standard USB
port-suspend directly, now the suspend routine in usb_generic is
called.  In practice this should never affect anyone.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as884) finally implements the time-saving semantics
possible with the Power Management FREEZE and PRETHAW events.  Their
proper handling requires only that devices be quiesced, with
interrupts and DMA turned off; non-root USB devices don't actually
need to be put in a suspended state.  The patch checks and avoids
doing the suspend call when possible.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as880) strives to keep the PM core's idea of a USB
interface's power state in synch with usbcore's own idea.  In the end
this doesn't really matter, but it's better to be consistent.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the problem that accesses NULL pointer
when disconnected a cable while play music with usb-speaker.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I would like to submit Renesas R8A66597 USB HCD driver.

R8A66597 is Renesas USB 2.0 host and peripheral combined
controller device originally designed for embedded products.
As a limitation of this device, it does not support externel
hub more than 2 tier, and cannot communicate with a USB
device more than 10. Then this device is not compatible with
EHCI and/or OHCI, I wrote driver support patch based on
sl811 code.

This driver has the following unique specifications:
- Implement transfer timeout to share one pipe with plural endpoint.
- Detach detection of a USB device connected to externel hub.

The driver has been tested external hub, usb-hdd, usb-cdrom,
usb-speaker, mice, keyboard, and usbtest driver.

Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes the problem that used SA_* flags.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I would like to submit Renesas M66592 udc driver.

The M66592 is Renesas USB 2.0 peripheral controller.
This controller supports USB high-speed.

The driver has been tested Gadget Zero, Ethernet Gadget,
File-backed Storage Gadget, and passed usbtest script.

Signed-off-by : Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>