The new debugfs files keepalive and disconnect_timeout can be used to
fetch the current values and to change the values for keepalive and
disconnect event timeout (both in seconds).
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Roaming mode can be changed by writing roam mode (default, bssbias, or
lock) to roam_mode. Forced roam can be requested by writing the BSSID
into force_roam.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The new roam_table debugfs file can be used to display the current
roam table from the target.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There's no use for these, at least right now, so better to remove them.
If some of them are ever needed, we can always add them back.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add a new debug level ATH6KL_DBG_WMI_DUMP and other minor
improvements to the wmi debug messages.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Makes it easier to recognise longs dumps.

Obligatory screenshot using "rx" prefix:

ath6kl: ath6kl_rx
rx 00000000: 10 10 00 00 00 00 08 30 00 00 00 00 00 00 f9 0b  .......0........
rx 00000010: 2c 44 08 30 00 00 f9 0b 0c a4 02 00 00 00 73 d2  ,D.0..........s.
rx 00000020: 94 00 f9 0b 04 8c 01 00 02 00 07 02 02 00 f9 0b  ................
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This allows RSN pre-authentication to be used when roaming decisions are
done in the target.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now that we allow the first Beacon frame after each connection to
be processed at the host, we can figure out the DTIM period and
expose it with Beacon interval through STA info BSS parameters
to user space.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Since we may end up using a dummy BSS entry when roaming, allow one Beacon
frame -based bssinfo from the current BSS to be processed prior to starting
to filter all bssinfo events. This allows cfg80211 BSS table to be filled
with proper data in the roaming case where the full Beacon data may not
have been present at the time of roamed event.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There is no point in unconditionally converting the bssinfo header
to the old version since only the new header is being used and the
driver can as well read the values from it when needed. Leaving out
the conversion saves some extra memory copying.

In addition, use the calculated "rssi" value snr - 95 dBm to get the
proper value in cfg80211 BSS table (i.e., something that more or less
matches with the value used in STA info).
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now that the scan results are reported directly to the cfg80211 BSS
table there is no need for maintaining this internal node table
implementation for scan results. Remove the definitions and node
table functions.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The internal node table in ath6kl was not really used for any useful
purpose. It was just used to collect scan results during a scan and then
provide them in a burst to cfg80211 at the completion of the scan. There
is no point in doing this since cfg80211 is perfectly capable of
maintaining the BSS table and the BSS inform messages are sent in
separate function calls anyway.

This provides more complete information in the cfg80211 BSS table since
this allows Beacon and Probe Response frames to be distinguished and IEs
from them reported separately.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This event has been deprecated and there is no need for ath6kl to
include code for processing it.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Process the regulatory code from eeprom and pass the
country information to cfg80211.

kvalo: add space between struct name and *
Signed-off-by: NVivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This cleans up the connect event parsing by defining a union in
struct wmi_connect_event to match with the three possible sets of
fields that the target uses depending on which type of connect
event is being indicated. In addition, two AP cases are now
separated from ath6kl_connect_event() so that correct field names
can be used to make it actually possible to understand what the
code is doing.

The bug hiding in the previous mess was in parsing the AID incorrectly
when processing the new station connecting event in AP mode. The fix
here for that is also fixing TIM updates for PS buffering to use the
correct AID.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There is a 2-octet reserved field between the flag and aid fields. Fix
that to make the target actually behave as requested.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware initiates roaming only after it reaches a rssi of 20.
This lower rssi threshold can be modified through a wmi command
to modify the roaming behavior.

kvalo: rename debugfs functions and move comment about rssi units next to
ath6kl_wmi_set_roam_lrssi_cmd()
Signed-off-by: NVivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware log parameters can be controlled now with help of fwlog_mask
debugfs file.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Firmware sends binary logs with WMIX_DBGLOG_EVENTID event. Create
a buffer which stores the latest logs and which can be copied from
fwlog debugfs file with cp command.

To save memory firmware log support is enabled only when CONFIG_ATH6KL_DEBUG
is enabled.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is port from the staging version of ath6kl. The interface to user space
is exactly same.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use WMI_TX_STATUS_EVENTID event to generate cfg80211_mgmt_tx_frame()
calls. Since we support only a single pending frame for now, use the
hardcoded cookie value 1 and store a copy of the pending frame in
the driver.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NEdward Lu <elu@qca.qualcomm.com>
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The target is not ready to accept addkey commands until the connect
event has been delivered, so delay these operations for the initial GTK.
In addition, properly set interface connected and mark netdev ready when
the AP mode setup has been completed.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use cfg80211 add/del_beacon callbacks for starting/stopping AP mode and
set_beacon to update AP configuration (mainly, to update Beacon and
Probe Response IEs).
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use wlan_iterate_nodes() directly.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

By having scan_table in struct ath6kl, it makes sense to move initialization
to ath6kl_init() and deinitialization to ath6kl_destroy().
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Use the bssid from ath6kl directly.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is nothing but bssid of struct ath6kl.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

And remove the reference to wmi in ath6kl_node_table.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It does not need to be in wmi
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>