The new debugfs files keepalive and disconnect_timeout can be used to
fetch the current values and to change the values for keepalive and
disconnect event timeout (both in seconds).
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Roaming mode can be changed by writing roam mode (default, bssbias, or
lock) to roam_mode. Forced roam can be requested by writing the BSSID
into force_roam.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

The new roam_table debugfs file can be used to display the current
roam table from the target.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This file can be used to fetch endpoint statistics counters and
to clear them by writing 0 to it.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For some WPS test items, such as item "5.1.14"
STAUT must include the WSC IE in the 802.11 Association Request frame.
Therefore, add the corresponding IE in association message.
Signed-off-by: NKevin Fang <kevin.fang@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

smatch found that skb might be null in some cases in ath6kl_rx():

ath6kl/txrx.c +1252 ath6kl_rx(222) error: potential null derefence 'skb'.

This will happen when ath6kl is in AP mode and two clients send traffic
to each other.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now htc_hif.h can be removed.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Also remove some cache line optimisation. It was using hardcoded values
which is wrong.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Currently only a warning is emitted but no error is returned.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It was missing endian annotation.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There's no use for these, at least right now, so better to remove them.
If some of them are ever needed, we can always add them back.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Power save is enabled during ath6kl init. But when user space disables power
save, the system will go into suspend with power save disabled. The ath6kl
driver will now explicitly enable power save prior to entering suspend and
restore its previous setting upon resume
Signed-off-by: NChilam Ng <chilamng@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is just a four byte information of the received message
from ath6kl_htc_rxmsg_pending_handler(). Remove unnecessary
array representaion.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is not necessary to process an htc_packet which is allocated for rx
but failed in sdio rx. Though it does not fix any real issue, it does
not make much sense to process the failed frame.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is found during the code review. As the leak would happen only
in failure case, the imapct is not easily visible.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Packet is not reclaimed when ath6kl_htc_rx_process_hdr() fails.
Fix this by deferring the packet deletion from comp_pktq till
ath6kl_htc_rx_process_hdr() returns success. This bug is found
in code review, impact is not easily visible as the leak happens
only in failure cases.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

There are places where tx_complete callbacks are called with
claiming the sdio function. It is not necessary to hold the
sdio func for longer. This may even affect the host side power
save, if it is supported by the controller.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It is not necessary to use spinlock primitive to
protect data which is accessed in hard irq context as
nothing is running in hard irq with this driver. The
spinlock primitive meant to protect data in softirq
context is more appropriate.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This was disabled beacause there was a network stall
issue when scan is issued. This issue does not happen
with the new firmware (3.1.1.609), enable it back.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

For probe responses it can be useful to not wait for ACK to
avoid retransmissions if the station that sent the probe is
already on the next channel, so allow userspace to request
not caring about the ACK with a new nl80211 flag.

Since mac80211 needs to be updated for the new function
prototype anyway implement it right away -- it's just a
few lines of code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add the ability to advertise that the device
contains the AP SME and what features it can
support. There are currently no features in
the bitmap -- probe response offload will be
advertised by a few patches Arik is working
on now (who took over from Guy Eilam) and a
device with AP SME will typically implement
and require response offload.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add interface address so it can be mapped to a local
interface.  Add max-ampdu and mpdu-density.

Print out the tid->baw_size
Signed-off-by: NBen Greear <greearb@candelatech.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Based on a quick test, TDLS seemed to be working fine with ath9k, so
let's start advertising support for this in the driver.
Signed-off-by: NJouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The initval tables are updated as per system team input to improve
rx performance and power accuracy at 5GHz.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

AR9462 chips have the capabilities to provoide bluetooth
profile information. For non-AR9462 btcoex chips, the BT
priority traffic was identified by periodically polling
the respective registers and updated dutycycle, stomptype,
etc. As AR9462 chip offers the BT profile informations,
let us make use of that to update aggregation limit,
dutycycle, stomptype and wieghtages.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

To improve CCK sensitivity for AR9462 chips, performing
spur mitigation at 2440, 2464 frequencies alone is sufficient.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The code here treats very large values of "limit" as less than
MAX_POWER_RATE because of the cast to int.  We should do the compare
as u32 instead.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This happens with devices using a regulatory domain 0x68 that are only
5Ghz capable because ath_reg_apply_active_scan_flags assumes that we
always have a 2,4Ghz band.

CPU 0 Unable to handle kernel paging request at virtual address 00000000, epc == 82cd838c, ra == 82cd8384
Oops[#1]:
Cpu 0
$ 0 : 00000000 00000061 00000003 00000024
$ 4 : 00000003 000016c1 82f900ac 00000024
$ 8 : 00000000 82cda304 0058bad8 00000005
$12 : 005908f8 001e8481 00000003 1dcd6500
$16 : 00000002 00000000 82c700c0 82c700c0
$20 : 82d415e4 82c70d64 82c70200 82c715bc
$24 : 00000000 11e1a300
$28 : 82ce2000 82ce3c70 82c715a8 82cd8384
Hi : 00000000
Lo : 0000001e
epc : 82cd838c ath_reg_apply_world_flags+0x78/0x17c [ath]
Not tainted
ra : 82cd8384 ath_reg_apply_world_flags+0x70/0x17c [ath]
Status: 1000d403 KERNEL EXL IE
Cause : 80800008
BadVA : 00000000
PrId : 00019374 (MIPS 24Kc)
Modules linked in: ath9k(+) ath9k_common ath9k_hw ath mac80211 cfg80211
	compat_firmware_class compat arc4 aes_generic deflate ecb cbc
	leds_gpio button_hotplug gpio_buttons input_polldev ie
Process insmod (pid: 464, threadinfo=82ce2000, task=838b31d8, tls=00000000)
Stack : 00000000 00000002 82f900ac 82c700c0 82d415e4 82c70d64 00000000 00000068
82f900ac 82cd88f4 82c700c0 82cda304 00000001 000020f0 82f90000 82c70d40
00000002 82f90000 82f900ac 82d4207c 82d518a0 00000002 7fee6118 8017c0d8
00000008 8397ba00 82c70d40 00000000 82c70200 83813000 83813058 b0010000
82d518a0 00000002 7fee6118 82d4b8c8 83445cc0 80120dc0 83804000 800eeda0
...
Call Trace:
[<82cd838c>] ath_reg_apply_world_flags+0x78/0x17c [ath]
[<82cd88f4>] ath_regd_init+0x464/0x488 [ath]
[<82d4207c>] ath9k_init_device+0x6a4/0x6b4 [ath9k]
[<82d4b8c8>] ath_pci_probe+0x27c/0x358 [ath9k]
[<80181de0>] pci_device_probe+0x64/0xa4
[<8019e874>] driver_probe_device+0xb8/0x190
[<8019e9b8>] __driver_attach+0x6c/0xa4
[<8019dfc0>] bus_for_each_dev+0x60/0xb0
[<8019d744>] bus_add_driver+0xc4/0x25c
[<8019ed6c>] driver_register+0xe0/0x198
[<8018206c>] __pci_register_driver+0x50/0xe0
[<82dd0010>] ath9k_init+0x10/0x54 [ath9k]
[<8006b4a0>] do_one_initcall+0x68/0x1ec
[<800a901c>] sys_init_module+0xec/0x23c
[<80062544>] stack_done+0x20/0x3c
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

During the fast channel change noise floor values are being loaded
twice at init_cal and after channel_change. The commit "ath9k_hw:
Improve fast channel change for AR9003 chips" overlooked it that
caused failure to load nf while doing bgscan. This patch performs noise
floor calibration after the fast and full reset.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes system hang when resuming from S3 state
and lower rate sens failure issue.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Previously the driver did not care if TX_CTL_REQ_TX_STATUS
was set on aggregated frames or not and it would silently
drop successfully sent frames if possible [much like:
"no news is good news!"].

But, TX_CTL_REQ_TX_STATUS was invented for a reason and
no tx status report should ever be dropped if it is set.
Reported-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The commit ce407afc introduced regression for AR9330/AR9340
register offsets. Some of the register offsets are common
for AR9330/AR9340/AR9485 except AR9380. Fix that.

Cc: stable@kernel.org [3.1.0+]
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

IQ calibration during fast channel change sometimes failed
with RTT. And also restoring invalid radio retention readings
during init cal could cause failure to set the channel properly.
This patch counts the valid rtt history readings and clears
rtt mask.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

My recent commits (3782c69d, 324c74ad) introduced regression
for register offset selection that based on the macversion.
Not using parentheses in proper manner for ternary operator
leads to select wrong offset for the registers.

This issue was observed with AR9462 chip that immediate disconnect
after the association with the following message

ieee80211 phy3: wlan0: Failed to send nullfunc to AP 00:23:69:12:ea:47
after 500ms, disconnecting.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Renamed to be in sync with Marketing term and to avoid
confusion with other chip names.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The AR946/8x chips are 2x2 Dual band with BT support. In order
to avoid misleading with other chips and to be in sync with
marketing team's term, AR9480 is renamed as AR9462.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Support the fast channel change across band switch only when there
are available of reusable cabliration results. And also observed that
doing agc control calibration on fastcc, sometimes causing calibration
timeout. Hence changing agc control to be run only on full chip reset.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Supported calibrations of radio retention table (RTT) are
	- DC offset
	- Filter
	- Peak detect
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>