Attached is a driver for SMSC's LAN911x and LAN921x families of embedded
ethernet controllers.

There is an existing smc911x driver in the tree; this is intended to
replace it.  Dustin McIntire (the author of the smc911x driver) has
expressed his support for switching to this driver.

This driver contains workarounds for all known hardware issues, and has
been tested on all flavours of the chip on multiple architectures.

This driver now uses phylib, so this patch also adds support for the
device's internal phy
Signed-off-by: NSteve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: NBahadir Balban <Bahadir.Balban@arm.com>
Signed-off-by: NDustin Mcintire <dustin@sensoria.com>
Signed-off-by: NBill Gatliff <bgat@billgatliff.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch removes some trailing whitespaces and spaces before tabs.
Signed-off-by: NHannes Hering <hering2@de.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The TX watchdog should trigger a reset, but a temperature/power alarm
should not as this is unlikely to solve the problem.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Add board monitoring to periodic work whenever link is down.
For SFE4001, report when a fault has caused the PHY to turn off.
For SFE4002, switch XFP PHY into low-power state in case of a fault.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

The boot code that appears as a PCI expansion ROM on the SFC4000 is
stored in flash.  Expose this as a standard MTD device to allow for
in-place upgrades.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Move flash and EEPROM partition boundary constants into spi.h and rename
them to be consistent.

Add a comment on the partitioning.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Due to a hardware bug, the originally assigned range cannot reliably
be used for boot configuration and must not be modifiable through
ethtool.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

	This patch implements alternative aggregator selection policies
for 802.3ad.  The existing policy, now termed "stable," selects the active
aggregator by greatest bandwidth, and only reselects a new aggregator
if the active aggregator is entirely disabled (no more ports or all ports
down).

	This patch adds two new policies: bandwidth and count, selecting
the active aggregator by total bandwidth (like the stable policy) or by
the number of ports in the aggregator, respectively.  These two policies
also differ from the stable policy in that they will reselect the active
aggregator when availability-related changes occur in the bond (e.g.,
link state change).

	This permits "gang failover" within 802.3ad, allowing redundant
aggregators along parallel paths to always maintain the "best" aggregator
as the active aggregator (rather than having to wait for the active to
entirely fail).

	This patch also updates the driver version to 3.5.0.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

	The current ALB function that processes incoming ARPs
does not handle traffic for VLANs configured above bonding.  This causes
traffic on those VLANs to all be assigned the same slave.  This patch
corrects that misbehavior by locating the bonding interface nested below
the VLAN interface.

	Bug reported by Sven Anders <anders@anduras.de>, who also
tested an earlier version of this patch and confirmed that it resolved
the problem.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This patch adds better IPv6 failover support for bonding devices,
especially when in active-backup mode and there are only IPv6 addresses
configured, as reported by Alex Sidorenko.

- Creates a new file, net/drivers/bonding/bond_ipv6.c, for the
   IPv6-specific routines.  Both regular bonds and VLANs over bonds
   are supported.

- Adds a new tunable, num_unsol_na, to limit the number of unsolicited
   IPv6 Neighbor Advertisements that are sent on a failover event.
   Default is 1.

- Creates two new IPv6 neighbor discovery functions:

   ndisc_build_skb()
   ndisc_send_skb()

   These were required to support VLANs since we have to be able to
   add the VLAN id to the skb since ndisc_send_na() and friends
   shouldn't be asked to do this.  These two routines are basically
   __ndisc_send() split into two pieces, in a slightly different order.

- Updates Documentation/networking/bonding.txt and bumps the rev of bond
   support to 3.4.0.

On failover, this new code will generate one packet:

- An unsolicited IPv6 Neighbor Advertisement, which helps the switch
   learn that the address has moved to the new slave.

Testing has shown that sending just the NA results in pretty good
behavior when in active-back mode, I saw no lost ping packets for example.
Signed-off-by: NBrian Haley <brian.haley@hp.com>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

A packet dequeued and stored as gso_skb in qdisc_peek_dequeued() should
be seen as part of the queue for sch->q.qlen queries until it's really
dequeued with qdisc_dequeue_peeked(), so qlen needs additional updating
in these functions. (Updating qstats.backlog shouldn't matter here.)
Signed-off-by: NJarek Poplawski <jarkao2@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I have been tracking for a while a case where when the
network namespace exits the cleanup gets stck in an
endless precessess of:

unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3
unregister_netdevice: waiting for lo to become free. Usage count = 3

It turns out that if you listen on a multicast address an unsubscribe
packet is sent when the network device goes down.   If you shutdown
the network namespace without carefully cleaning up this can trigger
the unsubscribe packet to be sent over the loopback interface while
the network namespace is going down.

All of which is fine except when we drop the packet and forget to
free it leaking the skb and the dst entry attached to.  As it
turns out the dst entry hold a reference to the idev which holds
the dev and keeps everything from being cleaned up.  Yuck!

By fixing my earlier thinko and add the needed kfree_skb and everything
cleans up beautifully. 
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I was recently hunting a bug that occurred in network namespace
cleanup.  In looking at the code it became apparrent that we have
and will continue to have cases where if we have anything going
on in a network namespace there will be assumptions that the
loopback device is present.   Things like sending igmp unsubscribe
messages when we bring down network devices invokes the routing
code which assumes that at least the loopback driver is present.

Therefore to avoid magic initcall ordering hackery that is hard
to follow and hard to get right insert a call to register the
loopback device directly from net_dev_init().    This guarantes
that the loopback device is the first device registered and
the last network device to go away.
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When physical devices are inside of network namespace and that
network namespace terminates we can not make them go away.  We
have to keep them and moving them to the initial network namespace
is the best we can do.

For virtual devices left in a network namespace that is exiting
we have no need to preserve them and we now have the infrastructure
that allows us to delete them.  So delete virtual devices when we
exit a network namespace.  Keeping the necessary user space clean up
after a network namespace exits much more tractable.
Acked-by: NDaniel Lezcano <dlezcano@fr.ibm.com>
Acked-by: NPavel Emelyanov <xemul@openvz.org>
Signed-off-by: NEric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I noticed a contention on udp_memory_allocated on regular UDP applications.

While tcp_memory_allocated is seldom used, it appears each incoming UDP frame
is currently touching udp_memory_allocated when queued, and when received by
application.

One possible solution is to use sk_mem_reclaim_partial() instead of
sk_mem_reclaim(), so that we keep a small reserve (less than one page)
of memory for each UDP socket.

We did something very similar on TCP side in commit
9993e7d3
([TCP]: Do not purge sk_forward_alloc entirely in tcp_delack_timer())

A more complex solution would need to convert prot->memory_allocated to
use a percpu_counter with batches of 64 or 128 pages.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This inserts the required de-allocation routines for memory allocated
by feature negotiation in the socket destructors, replacing
dccp_feat_clean() in one instance.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This provides feature-negotiation initialisation for both DCCP sockets
and DCCP request_sockets, to support feature negotiation during
connection setup.

It also resolves a FIXME regarding the congestion control
initialisation.

Thanks to Wei Yongjun for help with the IPv6 side of this patch.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds list initial fields and list management functions for the
new feature negotiation implementation.

Thanks to Arnaldo for suggestions and improvements.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A lookup table for feature-negotiation information, extracted from RFC
4340/42, is provided by this patch. All currently known features can
be found in this table, along with their feature location, their
default value, and type.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NIan McDonald <ian.mcdonald@jandi.co.nz>
Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares for the new and extended feature-negotiation
routines.

The following feature-negotiation data structures are provided:
	* a container for the various (SP or NN) values,
	* symbolic state names to track feature states,
	* an entry struct which holds all current information together,
	* elementary functions to fill in and process these structures.

Entry structs are arranged as FIFO for the following reason: RFC 4340
specifies that if multiple options of the same type are present, they
are processed in the order of their appearance in the packet; which
means that this order needs to be preserved in the local data
structure (the later insertion code also respects this order).

The struct list_head has been chosen for the following reasons: the most
frequent operations are

 * add new entry at tail (when receiving Change or setting socket
   options);
 * delete entry (when Confirm has been received);
 * deep copy of entire list (cloning from listening socket onto
   request socket).

The NN value has been set to 64 bit, which is a currently sufficient
upper limit (Sequence Window feature has 48 bit).

Thanks to Arnaldo, who contributed the streamlined layout of the entry
struct.
Signed-off-by: NGerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All these individual parsing functions never return an error,
so they can be void.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.

Drivers need not do it any more.

Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Removed duplicated #include <rdma/ib_verbs.h> in net/9p/trans_rdma.c
		and  #include <linux/thread_info.h> in net/socket.c
Signed-off-by: NJianjun Kong <jianjun@zeuux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

I want to compile out proc_* and sysctl_* handlers totally and
stub them to NULL depending on config options, however usage of &
will prevent this, since taking adress of NULL pointer will break
compilation.

So, drop & in front of every ->proc_handler and every ->strategy
handler, it was never needed in fact.
Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

	The only user of the net_device->last_rx field is bonding.
This patch adds a conditional update of last_rx to the bonding special
logic in skb_bond_should_drop, causing last_rx to only be updated when
the ARP monitor is running.

	This frees network device drivers from the necessity of
updating last_rx, which can have cache line thrash issues.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch gets about 1.25% back on tbench regression.

My change to NAPI for multiqueue support changed the time limit on
network receive processing.  Under sustained loads like tbench, this
can cause the receiver to reschedule prematurely. 
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

put_dec_trunc prints the digits in reverse order and is reversed
inside number(). Continue using put_dec_trunc, but reverse each quad
in ip4_addr_string.

[Noticed by Julius Volz]
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove the 'supports_ipv6' scheduler flag since all schedulers now
support IPv6.
Signed-off-by: NJulius Volz <julius.volz@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add IPv6 support to LBLC and LBLCR schedulers. These were the last
schedulers without IPv6 support, but we might want to keep the
supports_ipv6 flag in the case of future schedulers without IPv6
support.
Signed-off-by: NJulius Volz <julius.volz@gmail.com>
Acked-by: NSimon Horman <horms@verge.net.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the version to 3.95.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the BCM50610 to the list of phys supported by the
broadcom driver.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes the expansion register access routines a little more
formal.  They will be used by the following bcm50610 support patch.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds flow control support to Broadcom phys.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refines support for the 5785 device.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch refines the phylib support in the tg3 driver.  The patch does
the following things :

* Rename tg3_mdio_config() to tg3_mdio_config_5785().  The 5785 will be
  the only device that will use it so the name might as well reflect
  that.
* Fix a memory leak if mdiobus_register() fails.
* Add code to deal with phy device detection failures.
* Add code to correct the supported list of phy features based on the
  MAC <=> PHY interface.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch allows WOL to be enabled for Broadcom phys under phylib
control.  The only exception is the AC131, which has a completely
different register set.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 12dac075 ("tg3: adapt tg3 to
use reworked PCI PM code") introduced the new PCI PM API to the tg3
driver.  The patch was understandably conservative, so this patch
elaborates on that work.

The patch starts by creating a single point in tg3_set_power_state()
to decide whether or not to enable WOL.  The rest of the code in
tg3_set_power_state() was then pivoted to use the result of this
decision.

The patch then makes sure the device is allowed to wakeup before
reporting whether or not WOL is currently enabled.  The final hunks of
the patch consolidate where the WOL capability and WOL enabled flags
are set to a single location.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, phylib reports appear with a eth%d prefix.  Move the line
after register_netdev() and place it alongside the other informative
messages.  Update nearby informative messages accordingly.
Signed-off-by: NMatt Carlson <mcarlson@broadcom.com>
Signed-off-by: NMichael Chan <mchan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>