When this driver was initially submitted, the system would crash unless
ASPM was disabled. This problem has been fixed.

This patch also adds a printk that outputs the name of the firmware
file that is used.
Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In driver rtlwifi, efuse_read() places two relatively large arrays on the
stack - a 1D u8 array of size 128, and a 2D array of u16 with 128 * 4 elements.
With driver rtl8192de, the sizes will be 256 and 256 * 4 respectively. As that
will make the 2D array be 2048 bytes, I have changed the code to use kmalloc to
allocate the space.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The function iwl_is_any_associated() was intended
to check both contexts, but due to an oversight
it only checks the BSS context. This leads to a
problem with scanning since the passive dwell
time isn't restricted appropriately and a scan
that includes passive channels will never finish
if only the PAN context is associated since the
default dwell time of 120ms won't fit into the
normal 100 TU DTIM interval.

Fix the function by using for_each_context() and
also reorganise the other functions a bit to take
advantage of each other making the code easier to
read.

Cc: stable@kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Processing TSF out of range before RX helps to update beacon
timers so early in the succeeding rx process.
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The assumsion is that while processing ath9k tasklet,
interrupts were already disabled and it will be enabled
at the completion of ath9k tasklet. But whenever TSFOOR is raised,
the driver configures the beacon timers after having received a
beacon frame from the AP which inturn enables the interrupts.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When mac80211 is built without CONFIG_PM being defined, the following errors
are output:

net/mac80211/main.c: In function ‘ieee80211_register_hw’:
net/mac80211/main.c:700: error: ‘const struct ieee80211_ops’ has no member named ‘suspend’
net/mac80211/main.c:700: error: ‘const struct ieee80211_ops’ has no member named ‘resume’
make[2]: *** [net/mac80211/main.o] Error 1
make[1]: *** [net/mac80211] Error 2
make[1]: *** Waiting for unfinished jobs....
make: *** [net] Error 2
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

commit 5ed540ae change the led behavior
for iwlwifi driver; the side effect cause led blink all the time.

Modify the led blink table to fix this problem
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These warnings are exposed by gcc 4.6.
net/wireless/reg.c: In function 'freq_reg_info_regd':
net/wireless/reg.c:675:38: warning: variable 'pr' set but not used
[-Wunused-but-set-variable]
net/wireless/lib80211_crypt_wep.c: In function 'lib80211_wep_build_iv':
net/wireless/lib80211_crypt_wep.c:99:12: warning: variable 'len' set but
not used [-Wunused-but-set-variable]
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge branch 'wireless-next-2.6' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-2.6

DMA mappings can fail, but the current code
doesn't check for that. Add checking, which
requires some restructuring for proper error
paths.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

All AGN devices need the bytecount table, so
remove the indirection and make the functions
static again.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The device doesn't use the bytecount table for the
command queue, only for aggregation queues to make
aggregation decisions. So don't update it for the
command queue (and we even updated it with wrong
values).
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The variable 'len' here is set but never used.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

The frame pre-allocation is quite a bit of complex
code, all to avoid a single allocation. Remove it
and consolidate the beacon sending code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

There's no need for this, all commands are the right size.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

This patch adds the feature to support the test mode operation through
the generic netlink channel NL80211_CMD_TESTMODE between intel
wireless device iwlwifi and the user space application svtool.

The main purpose is to create a transportation layer between the iwlwifi
device and the user space application so that the interaction between the
user space application svtool and the iwlwifi device in the kernel space is
in a way of generic netlink messaging.

The detail specific functions are:

1. The function iwl_testmode_cmd() is added to digest the svtool test command
   from the user space application. The svtool test commands are categorized  to
   three types : commands to be processed by the device ucode, commands to access
   the registers, and commands to be processed at the driver level(such as reload
   the ucode). iwl_testmode_cmd() dispatches the commands the corresponding handlers
   and reply to user space regarding the command execution status. Extra data is
   returned to the user space application if there's any.

2. The function iwl_testmode_ucode_rx_pkt() is added to multicast all the spontaneous
   messages from the iwlwifi device to the user space. Regardless the message types,
   whenever there is a valid spontaneous message received by the iwlwifi ISR,
   iwl_testmode_ucode_rx_pkt() is invoked to multicast the message content to user
   space. The message content is not attacked and the message parsing is left to
   the user space application.

Implementation guidelines:

1. The generic netlink messaging for iwliwif test mode is through  NL80211_CMD_TESTMODE
   channel, therefore, the codes need to follow the regulations set by cfg80211.ko
   to get the actual device instance ieee80211_ops via cfg80211.ko, so that the iwlwifi
   device is indicated with ieee80211_ops and can be actually accessed.

   Therefore, a callback iwl_testmode_cmd() is added to the structure
   iwlagn_hw_ops in iwl-agn.c.

2. It intends to utilize those low level device access APIs from iwlwifi device driver
   (ie. iwlagn.ko) rather than creating it's own set of device access functions.
   For example, iwl_send_cmd(), iwl_read32(), iwl_write8(), and iwl_write32() are reused.

3. The main functions are maintained in new files instead of spreading all over the
   existing iwlwifi driver files.

   The new files added are :

   drivers/net/wireless/iwlwifi/iwl-sv-open.c
        - to handle the user space test mode application command
          and reply the respective command status to the user space application.
        - to multicast the spontaneous messages from device to user space.

   drivers/net/wireless/iwlwifi/iwl-testmode.h
        - the commonly referenced definitions for the TLVs used in
          the generic netlink messages
Signed-off-by: NCindy H. Kao <cindy.h.kao@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>

Since firmware is capable of generating IV's for all crypto
suits (TKIP, CCMP and WEP), do not ask mac80211 to generate
IV when HW crypto is being used. Instead only reserve
appropriate space in tx skb's in the driver, so that the
firmware can write IV's values.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were performing it on wrong core, it was outdated and is already
implemented in ssb.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We were performing it on wrong core, it was outdated and is already
implemented in ssb.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With AR9003 at about ~ 10 feet from an AP that uses RTS / CTS you
will be able to associate but not not get data through given that
the power for the rates used was set too low. This increases the
power and permits data connectivity at longer distances from
access points when connected with HT40. Without this you will not
get any data through when associated to APs configured in HT40
at about more than 10 feet away.

Cc: stable@kernel.org
Cc: Fiona Cain <fcain@atheros.com>
Cc: Zhen Xie <Zhen.Xie@Atheros.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Neha Choksi <neha.choksi@atheros.com>
Cc: Wayne Daniel <wayne.daniel@atheros.com>
Cc: Gaurav Jauhar <gaurav.jauhar@atheros.com>
Cc: Samira Naraghi <samira.naraghi@atheros.com>
CC: Ashok Chennupati <ashok.chennupati@atheros.com>
Cc: Lance Zimmerman <lance.zimmerman@atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch:
  rt2x00: Make rt2x00_queue_entry_for_each more flexible
  commit: 10e11568

introduced a severe regression on the throughput
for USB hardware. It turns out that the exiting of
the rt2x00queue_for_each_entry() was done too early.

The exact cause for this regression is unknown,
but by disabling the premature exiting of the loop
seems to resolve the issue.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Reported-by: NYasushi SHOJI <yashi@atmark-techno.com>
Reported-by: NBalint Viragh <bviragh@dension.com>
Tested-by: NBalint Viragh <bviragh@dension.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add necessary RF chipset define and basic support for these devices.
Tested-by: NJuan Carlos Garza <juancarlosgarza@gmail.com>
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.

This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.

Cc: stable@kernel.org
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds basic support for the new WoWLAN
configuration in mac80211. The behaviour is
completely offloaded to the driver though,
with two new callbacks (suspend/resume).

Options for the driver include a complete
reconfiguration after wakeup, and exposing
all the triggers it wants to support.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is based on (but now quite far from) the
original work from Luis and Eliad. Add support
for configuring WoWLAN triggers, and getting
the configuration out again. Changes from the
original patchset are too numerous to list,
but one important change needs highlighting:
the suspend() callback is passed NULL for the
trigger configuration if userspace has not
configured WoWLAN at all.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, the driver only disable multicast filtering when the
FIF_ALLMULTI driver flag has been just set (ie,
if changed_flags& FIF_ALLMULTI and *new_flags& FIF_ALLMULTI) or else
it will reenable multicast filtering.

But next time, this condition will be false and multicast filtering
will be reenabled, even through FIF_ALLMULTI is still set.

This mean that allmulticast only works for less than two minutes in
ad-hoc mode.  This patch fixes that to disable multicast filtering
as long as FIF_ALLMULTI is set.
Signed-off-by: NNicolas Cavallari  <cavallar@lri.fr>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The WEP key length was being set to 0 erroneously which broke WEP support.
Fix the same by setting the key length appropriately.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The only user of WIPHY_FLAG_SUPPORTS_SEPARATE_DEFAULT_KEYS was removed
and consequently, this flag can be removed, too. In addition, a single
capability flag was not enough to indicate this capability clearly since
the device behavior may be different based on which operating mode is
being used.
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit dbd2fd65 added a mechanism for
user space to indicate whether a default key is being configured for
only unicast or only multicast frames instead of all frames. This
commit added a driver capability flag for indicating whether separate
default keys are supported and validation of the set_key command based
on that capability.

However, this single capability flag is not enough to cover possible
difference based on mode (AP/IBSS/STA) and the way this change was
introduced resulted in a regression with drivers that do not indicate
the new capability (i.e.., more or less any non-mac80211 driver using
cfg80211) when using a recent wpa_supplicant snapshot.

Fix the regression by removing the new check which is not strictly
speaking needed. The new separate default key functionality is needed
only for RSN IBSS which has a separate capability indication.

Cc: stable@kernel.org
Signed-off-by: NJouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Skip initialization of local variables with some default values
if the values are not going to be used further down the code path.
Signed-off-by: NYogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When scan and assoc (infra/ibss) commands are simultaneously
given in two terminals, association response is erroneously
served while serving the scan response.

mwifiex_cfg80211_results() is the common routine for sending
ioctl (scan, assoc etc.) results to cfg80211 stack. In above
scenario even if the common routine is called for scan ioctl
context, it also tries to send information about assoc ioctl to
cfg80211 because "priv->assoc_request/priv->ibss_join_request"
flag is on at that time.

Fix the issue by updating request variable after assoc handling
and modifying the variable check in mwifiex_cfg80211_results.
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Modify rtlwifi routines for rtl8192se and set up Kconfig
and Makefile for new driver.

This patch also disables ASPM for the RTL8192SE to prevent some strange
crashes on LF's system.
Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge routines trx.c and trx.h for RTL8192SE.
Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge routines table.c and table.h for RTL8192SE.
Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge routines sw.c and sw.h for RTL8192SE.
Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge routines rf.c and rf.h for RTL8192SE.
Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge routines reg.h for RTL8192SE.
Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge routines phy.c and phy.h for RTL8192SE.
Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge routines led.c and led.h for RTL8192SE.
Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Merge routines hw.c and hw.h for RTL8192SE.
Signed-off-by: NChaoming_Li <chaoming_li@realsil.com.cn>
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>