The ath6kl responds to probe-requests in HW while operating as an AP. It
supports offloading exclusions to support the WPS, WPS2, P2P and
802.11u protocols.
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This patch supports Marvell chipset 88W8797 (Avastar) with
SDIO interface.

The corresponding firmware image file is located at:
"mrvl/sd8797_uapsta.bin"
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NTristan Xu <xurf@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NKiran Divekar <dkiran@marvell.com>
Signed-off-by: NFrank Huang <frankh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Don't use the interruptible variant of mutex_lock(). It doesn't really
need to be interruptible. This avoids nasty error handling.
Signed-off-by: NMichael Buesch <m@bues.ch>
Acked-by: NChristian Lamparter <chunkeey@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some drivers (e.g. ath9k) assume that it's safe to go into low-power mode
immediately after the idle state changes. To support that, mac80211 even
calls drv_flush() before that happens.
In some instances, mac80211 sent a packet right after recalculating the
idle state, this patch fixes that.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Convert various seemingly still compiled wireless drivers' .get_drvinfo
routines to use the preferred strlcpy() routine.
Signed-off-by: NRick Jones <rick.jones2@hp.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove unused function parameters in the following functions:
minstrel_calc_rate_ewma()
minstrel_ht_calc_tp()
minstrel_aggr_check()
minstrel_ht_set_rate()
Signed-off-by: NPatrick Kelle <patrick.kelle81@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We recently introduced a return here, but we need to call kfree
first.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

sk_buff structs should be freed using kfree_skb().

This was introduced recently in 02945821 "mac80211: Save probe
response data for bss".
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Finding the group index for a specific rate is done by looping through
all groups and returning if the correct one is found. This code is
called for each tx'ed frame and thus it makes sense to reduce its
runtime.

Do this by calculating the group index by this formula based on the SGI
and HT40 flags as well as the stream number:

idx = (HT40 * 2 * MINSTREL_MAX_STREAMS) +
      (SGI * MINSTREL_MAX_STREAMS) +
      (streams - 1)

Hence, the groups are ordered by th HT40 flag first, then by the SGI
flag and afterwards by the number of used streams.

This should reduce the runtime of minstrel_ht_get_group_idx
considerable.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The drivers are not required to fill in rate->count if rate->idx is set
to -1. Hence, we should first check rate->idx before accessing
rate->count.
Signed-off-by: NHelmut Schaa <helmut.schaa@googlemail.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The shared key authentication frame that needs to be
encrypted (the third one in the shared key handshake)
is directly encrypted in ieee80211_send_auth and the
IEEE80211_TX_INTFL_DONT_ENCRYPT is set. All others
are not encrypted, so the only way to get to this is
erroneously on no-monitor AP side.

Remove the special case for authentication frames to
fix the AP shared key side when operating without
cooked monitor interfaces -- with cooked monitor the
IEEE80211_TX_INTFL_DONT_ENCRYPT also gets set, so we
never get here -- an AP never encrypts auth frames.

Without this patch, an AP operating in WEP mode with
my no-monitor patches would erroneously encrypt all
authentication frames, instead of none.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add and use pr_fmt and pr_<level>
Remove useless double parentheses from macros.
Remove function names from format strings, add to pr_debug use.
Coalesce formats.
Remove uncompileable undeclared variable in a DMA_NONE use.
Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix indentation in nci.h file.
Signed-off-by: NIlan Elias <ilane@ti.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove all wlan weight macros and group it together for better
understanding & readability. It makes the code reusable for
AR9462 wlan weights.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes btcoex_enable from stomp type change and let
it be called from callee functions that makes the code can be
reusable for MCI changes.
Signed-off-by: NRajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When operating AP interface is brough down the mode is reset to
STA. This STA will be reconfigured into AP mode when the interface
is brought up again. This sequence will be successful only when
change_virtual_intf() returns with no error, but there is a
check in this callback which does the type change only when
that interface is active. This callback does nothing more
than saving the new interface type to vif and wdev, so the
sanity check for interface state and wmi state is not necessary.
This makes the AP interface functional again after interface down/up.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Connect control flag CONNECT_WPS_FLAG has to be cleared
by default even if the driver receives zero length IE
from cfg80211.

Otherwise this flag would be always set after WPS exchange
which would lead wpa_supplicant to fail to connect with
the received WPS credentials. This issue is observed only
in OPEN security.

kvalo: use cfg80211 instead of CFG in the commit log
Signed-off-by: NRaja Mani <rmani@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Not all firmwares support multiple vifs and we need to read the limit from
the firmware image.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Needed when detecting how many vifs firmware supports.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

When adding ar6004 SDIO support I forgot to add corresponding
MODULE_FIRMWARE() definitions to sdio.c.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Part of ath6kl uses "REV3" style of naming hardware versions and elsewhere
"hw 2.1.1" is used instead for the same version. This is confusing, use
the latter term everywhere.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

To make it easier to print name for each hardware type. Also move the hw
info print to ath6kl_init_hw_start() which is more logical place for it.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Board data address can change between firmwares so we need to read that
from the firmware image.

Also fix debug log for the patch address to print the address in hex.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is to make it configurable by firmware IEs. Also determine if we need
to write or read the board address to the chip by checking if board address
is set or not.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

It's easier to handle the values when they are defined in a struct.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Having separate defines, in a different file, makes it difficult to read
the actual values. As we are just setting named fields in a struct
the defines don't make any sense anymore.

There are no functional changes, only moving of constants.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

OPEN_AUTH is passed as dot11_auth_mode by default, this would
affect the AP mode when configured with shared authentication
type. Assign appropriate auth type to fix this from driver.
A patch in wpa_supplicant (wpa_supplicant: Set configured auth_algs)
is also needed to fix this.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

vif->def_txkey_index is set to key_index in ath6kl_cfg80211_add_key().
If the interface is configured with multiple static wep keys,
vif->def_txkey_index would be holding the index of the last key configured,
not the default tx key index. Remove this unnecessary default key index setting
in ath6kl_cfg80211_add_key() to configure the right key index in WEP thereby
make it work when multiple wep keys are configured.
Signed-off-by: NVasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Now two modules are built, ath6kl_sdio.ko and ath6kl_usb.ko. But the USB
module isn't fully functional yet as HTC layer is missing support and
that's why it's marked as experimental for now.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

As HTC layer doesn't support USB devices return an error if that happens.
USB support will be added to HTC in the future, this is just a temporary
solution.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add USB support for ar6004. Currently only firmware can be booted,
no commands can be sent to firmware yet as HTC layer doesn't work
with USB yet.

Based on patches by Kevin Fang.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

In some rare cases core code needs to know what hif type is used. Add
a field to struct ath6kl to denote that. Hopefully this is just a
temporary solution.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add support for AR6004 SDIO. Tested scan, association (open mode) and
ping.

kvalo: change commit log a bit, drop board address changes
Signed-off-by: NNaveen Gangadharan <ngangadh@qca.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

These have changed a bit since last time ar6004 code was commited.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

Add also hw 1.1.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>

This is preparation for USB support which will have different diag
commands.

Based on code by Kevin Fang.
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>