In this patch, increased the number of MSIX vector support for SAS3 C0 HBAs to
up-to 96.

Following are changes that are done in this patch

1. This feature is enabled only for SAS3 C0 and higher revision cards and also
only when reply post free queue count is greater than 8.

2. To support this feature 12 SupplementalReplyPostHostIndex system interfaces
are used. MSI-X index numbered from 0 to 7 use the first
SupplementalReplyPostHostIndex system interface to update its corresponding
ReplyPostHostIndex values, MSI-X index numbered from 8 to 15 will use the
second SupplementalReplyPostHostIndex system interface and so on. These 12
SuppementalReplyPostHostIndex system interfaces address are saved in the array
replyPostRegisterIndex[].

3. As each SupplementalReplyPostHostIndex register supports 8 MSI-X
vectors. So MSIxIndex field in these register must contain a value between 0
and 7.

4. After processing the reply descriptors from a reply post free queues then
update the new reply post host index value in ReplyPostHostIndex field and
(msix_index mod 8) value in MSIxIndex field of SupplementalReplyPostHostIndex
register. The Address of this SupplementalReplyPostHostIndex register is
retrived from (msix_index/8)th entry of replyPostRegisterIndex[] array.
Signed-off-by: NSreekanth Reddy <Sreekanth.Reddy@avagotech.com>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

We recently did some cleanup here and now the static checkers notice
that there is a missing error code when ioremap() fails.  Let's set it
to -ENOMEM.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

In the function storvsc_channel_init(), error code was not getting
set correctly in some of the failure cases. Fix this issue.
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Allow WRITE_SAME for Windows10 and above hosts.
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Use storage protocol version instead of vmbus protocol
version when determining storage capabilities.
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Use correct defaults for values determined by protocol negotiation,
instead of resetting them with every scsi controller.
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Currently we are making decisions based on vmbus protocol versions
that have been negotiated; use storage potocol versions instead.

[jejb: fold ARRAY_SIZE conversion suggested by Johannes Thumshirn
<jthumshirn@suse.de>
make vmstor_protocol static]
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Use a single value to track protocol versions to simplify
comparisons and to be consistent with vmbus version tracking.
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Rather than look for sets of specific protocol versions,
make decisions based on ranges. This will be safer and require fewer changes
going forward as we add more storage protocol versions.
Tested-by: NAlex Ng <alexng@microsoft.com>
Signed-off-by: NKeith Mange <keith.mange@microsoft.com>
Signed-off-by: NK. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The queuecommand routine has a local dev pointer used for the
dev_* prints. The two prints that currently exist are tucked
under a debug define and thus can be left out. Use the actual
location instead of a local to avoid this warning.

This patch is intended to be applied after the "CXL Flash Error
Recovery and Superpipe" series.
Signed-off-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NManoj N. Kumar <manoj@linux.vnet.ibm.com>
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

"port_sel" is a u64 so the shifting should also be a 64 bit shift.

Fixes: c21e0bbf ('cxlflash: Base support for IBM CXL Flash Adapter')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Acked-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The > should be >= or we read one element past the end of the array.

Fixes: c21e0bbf ('cxlflash: Base support for IBM CXL Flash Adapter')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Add support for physical LUN segmentation (virtual LUNs) to device
driver supporting the IBM CXL Flash adapter. This patch allows user
space applications to virtually segment a physical LUN into N virtual
LUNs, taking advantage of the translation features provided by this
adapter.
Signed-off-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NManoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: NMichael Neuling <mikey@neuling.org>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Add superpipe supporting infrastructure to device driver for the IBM CXL
Flash adapter. This patch allows userspace applications to take advantage
of the accelerated I/O features that this adapter provides and bypass the
traditional filesystem stack.
Signed-off-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NManoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: NMichael Neuling <mikey@neuling.org>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Introduce support for enhanced I/O error handling.

A device state is added to track 3 possible states of the device:

Normal - the device is operating normally and is fully operational

Limbo - the device is in a reset/recovery scenario and its operational
        status is paused

Failed/terminating - the device has either failed to be reset/recovered
                     or is being terminated (removed); it is no longer
                     operational

All operations are allowed when the device is operating normally. When the
device transitions to limbo state, I/O must be paused. To help accomplish
this, a wait queue is introduced where existing and new threads can wait
until the device is no longer in limbo. When coming out of limbo, threads
need to check the state and error out gracefully when encountering the
failed state. When the device transitions to the failed/terminating state,
normal operations are no longer allowed. Only specially designated
operations related to graceful cleanup are permitted.
Signed-off-by: NMatthew R. Ochs <mrochs@linux.vnet.ibm.com>
Signed-off-by: NManoj N. Kumar <manoj@linux.vnet.ibm.com>
Reviewed-by: NDaniel Axtens <dja@axtens.net>
Reviewed-by: NMichael Neuling <mikey@neuling.org>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

On certain conditions, login failures will just invoke
qla2x00_mark_device_lost() with the intend to do login again;
but if login_retry has been set already, that would fail to set the
relogin needed flag which is required to wakeup the DPC to retry.
Signed-off-by: NArun Easi <arun.easi@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NGiridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Fix for memory leak when command is not found by firmware due to
mismatch in sp reference count.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Instead of resetting the adapter wait for the login to timeout
and retry. Resetting the adapter can cause extended path recovery
times.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

If an SRB is NULL but the handle is in range just drop the
command instead of also resetting the adapter. If the handle
is in range then the command was valid at some point and may
have been aborted. Resetting the adapter can lead to extended
recovery times in this case.
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Aovid crashing the system in the scenario where firmware
just completes the command and it can not find the command
during abort mailbox processing. This scenario can lead to
sp reference counter being zero. Instead of crashing the
system, use WARN_ON to print warning in log file.
Signed-off-by: NHiral Patel <hiral.patel@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NSaurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Execute qla25xx_manipulate_risc_semaphore() only for
ssdid 0x0175 and 0x0240.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

When we get logged out, mark the port lost and set dpc flag for relogin.
Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Signed-off-by: NJoe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: NHimanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

scsi_error: should not get sense for timeout IO in scsi error handler

When an IO timeout occurs, the IO will be aborted in
scsi_abort_command() and SCSI_EH_ABORT_SCHEDULED will be set. Because
of that, the SCSI_EH_CANCEL_CMD will be clear in scsi_eh_scmd_add().
So when scsi error handler starts, it will get sense for this
timeout IO and the scmd of the IO request will be reused. In that
case, the scmd may be double released when racing with io_done(),
which will result in crash.
SO SCSI_EH_ABORT_SCHEDULED should also be checked when getting sense.
The bug maybe reproduced when the link between host and disk is
unstable.
Signed-off-by: NJiang Biao <jiang.biao2@zte.com.cn>
Signed-off-by: NLong Chun <long.chun@zte.com.cn>
Reviewed-by: NTan Hu <tan.hu@zte.com.cn>
Reviewed-by: NChen Donghai <chen.donghai@zte.com.cn>
Reviewed-by: NCai Qu <cai.qu@zte.com.cn>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Bump pm80xx driver version to 0.1.38.
Signed-off-by: NViswas G <Viswas.G@pmcs.com>
Reviewed-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The request has to be retried incase if the length of the SSP
Response IU is invalid.
Signed-off-by: NViswas G <Viswas.G@pmcs.com>
Reviewed-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

PORT RECOVERY TIMEOUT is the maximum time between the controller's
detection of the PHY down until the receipt of the ID_Frame (from the
same remote SAS port). If the time expires before the ID_FRAME is
received, the port is considered INVALID and can be removed. The
IOP_EVENT_PORT_RECOVERY_TIMER_TMO event is reported following the
IOP_EVENT_ PHY_DOWN event when the PHY/port does not recover after
Port Recovery Time.
Signed-off-by: NViswas G <Viswas.G@pmcs.com>
Reviewed-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

If the link error happens, we don't need to disconnect the phy,
which will remove the drive. Instead acknowledging the controller
and logging the error will be enough.
Signed-off-by: NViswas G <Viswas.G@pmcs.com>
Reviewed-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

In pm8001_ccb_task_free(), the dma unmapping is done based on
ccb->n_elem value. This should be initialized to zero in the
task_abort(). Otherwise, pm8001_ccb_task_free() will try for
dma_unmap_sg() which is invalid for task abort and can lead to
kernel crash.

Changes From V1:
None
Signed-off-by: NViswas G <Viswas.G@pmcs.com>
Reviewed-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Thermal page code has been changed to 7 for the 12G controllers.
Signed-off-by: NViswas G <Viswas.G@pmcs.com>
Reviewed-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

In Nexus reset the device state request are not needed.
Signed-off-by: NViswas G <Viswas.G@pmcs.com>
Reviewed-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Acked-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Updated 12G linkrate to libsas.
Signed-off-by: NViswas G <Viswas.G@pmcs.com>
Reviewed-by: NSuresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Reviewed-by: NJack Wang <jinpu.wang@profitbricks.com>
Reviewed-by: NTomas Henzl <thenzl@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Company has policy to use company email address, so update
my email address to company address.
Signed-off-by: NJack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Use logical instead of bitwise AND.
Signed-off-by: NSebastian Herbszt <herbszt@gmx.de>
Reviewed-by: NJames Smart <james.smart@avagotech.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>