Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add GPIO controller nodes to the r8a7779 core device tree.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add a pfc node to the r8a7779 device tree and remove manual pinmux
initialization from the corresponding board files.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Add an irqpin interrupt controller DT node on marzen-reference.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Allow configuration of the r8a7779 SoC SATA controller using a flattened device
tree.
Signed-off-by: NVladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

76cc1887
(thermal: rcar: add Device Tree support)
supported rcar_thermal DT probing.

rcar thermal driver doesn't support IRQ on r8a7779 chip
since it is using old design IRQ.
R-Car/R-Mobile next generation chips are using new design IRQ,
and rcar thermal driver is supporting these.

This patch adds rcar_thermal DT support for r8a7779 without IRQ.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

r8a7779 is not r8a7740 chip
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

The ethernet controller is not part of the r8a7779 SoC.

Cc: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

Allow a minimal setup of the r8a7779 SoC using a flattened device tree.
In particular, configure the i2c and ethernet controllers using a
flattened device tree.

SCI serial controller and TMU clock source, whose drivers do not yet
support configuration using a flattened device tree, are still configured
using C code in order to allow booting of a board with this SoC.

The ethernet controller also requires a regulator which is a board property.
A sample snippet DT for the marzen board is as follows:

/dts-v1/;
/include/ "r8a7779.dtsi"

/ {
	fixedregulator3v3: fixedregulator@0 {
		compatible = "regulator-fixed";
		regulator-name = "fixed-3.3V";
		regulator-min-microvolt = <3300000>;
		regulator-max-microvolt = <3300000>;
		regulator-boot-on;
		regulator-always-on;
	};
};

&lan0 {
	vddvario-supply = <&fixedregulator3v3>;
	vdd33a-supply = <&fixedregulator3v3>;
};
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

This allows the GIC interrupt controller of the  r8a7779 SoC to be
initialised using a flattened device tree blob.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

---

v3
* Fix copy-paste error and use unique reg values for each CPU

v2
As suggested by Mark Rutland
* Add reg and device_type to cpus
* Remove #address-cells from gic