- 07 9月, 2013 1 次提交
-
-
由 Tomasz Figa 提交于
Since pwm-samsung bindings require at least one clock to be specified, this patch adds the missing clocks and clock-names properties to specify clocks used by PWM block on Exynos4 SoCs. Signed-off-by: NTomasz Figa <t.figa@samsung.com> Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com> Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: NMike Turquette <mturquette@linaro.org>
-
- 03 9月, 2013 1 次提交
-
-
由 Laurent Pinchart 提交于
Replace the numerical polarity flags with the PWM_POLARITY_INVERTED symbolic constant. Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com> Reviewed-by: NStephen Warren <swarren@nvidia.com> Signed-off-by: NThierry Reding <thierry.reding@gmail.com>
-
- 30 8月, 2013 2 次提交
-
-
由 Dinh Nguyen 提交于
"dw-apb-timer-osc" and "dw-apb-timer-sp" are the same implementation of the DW APB timer, just fed by different clocks. Thus, deprecate both "dw-apb-timer-osc" and "dw-apb-timer-sp" in lieu of "dw-apb-timer". Signed-off-by: NDinh Nguyen <dinguyen@altera.com> Reviewed-by: NPavel Machek <pavel@denx.de> Acked-by: NStephen Warren <swarren@wwwdotorg.org> CC: Rob Herring <rob.herring@calxeda.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Ian Campbell <ian.campbell@citrix.com> CC: Arnd Bergmann <arnd@arndb.de> Cc: Olof Johansson <olof@lixom.net> CC: Jamie Iles <jamie@jamieiles.com> Cc: John Stultz <john.stultz@linaro.org> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Pavel Machek <pavel@denx.de> Cc: devicetree@vger.kernel.org Cc: linux-arm-kernel@lists.infradead.org Signed-off-by: NOlof Johansson <olof@lixom.net> v3: - Split out a separate that cleans up the timer entries and clock information. - Clearly states which binding is deprecated in the bindings doc. v2: - Deprecate the "dw-apb-timer-osc" and "dw-apb-timer-sp" but maintain backwards compatibility in the driver.
-
由 Boris BREZILLON 提交于
Fix phy0 address to match the reg property defined in phy0 node. Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com> Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 29 8月, 2013 1 次提交
-
-
由 Stephen Boyd 提交于
Let's follow the ratified DT binding and use uartdm instead of hsuart. This does break backwards compatibility but this shouldn't be a problem because the uart driver isn't probing on these devices without adding clock support (which isn't merged so far). Cc: David Brown <davidb@codeaurora.org> Acked-by: NKumar Gala <galak@codeaurora.org> Signed-off-by: NStephen Boyd <sboyd@codeaurora.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
-
- 28 8月, 2013 4 次提交
-
-
So I assumed that Beagle bone has only one USB port in host mode because the micro USB connector had an USB-UART there. I was wrong a little. The second port runs on host mode, but the micro USB plug is connected to an internal HUB with two ports: one to the USB-UART and one to musb instance one. For that reason, this patch enables both ports: the primary in device mode only and the second in host mode only. Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
This is what I observe: On the first connect, the musb starts with DEVCTL.Session set. On disconnect, musb_core calls try_idle. That functions removes the Session bit signalizing that the session is over (something that only in OTG is required). A new device, that is plugged, is no longer recognized. I've setup a timer and checked the DEVCTL register and I haven't seen a change in VBus and I saw the B-Device bit set. After setting the IDDIG into A mode and forcing the device to behave like a A device, I didn't see a change. Neither VBUS goes to 0b11 nor does a session start request comes. In the TI-v3.2 kernel they skip to call musb_platform_try_idle() in the OTG_STATE_A_WAIT_BCON state while not in OTG mode. Since the second port hast a standard A plug the patch changes the port to run in host mode only and skips the timer which would remove DEVCTL.Session so we can reconnect to another device later. Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
This relfects the code and dts requires changes due to recent .dts binding updates: - use mg prefix for the Metor Graphics specific attributes - use power in mA not in mA/2 as specifed in the USB2.0 specification - remove the child node for USB. This is driver specific on won't be reflected in the device tree - use the "mentor" prefix instead of "mg". - use "dr_mode" istead of "mg,port-mode" for the port mode. The former is used by a few other drivers. Cc: Rob Herring <rob.herring@calxeda.com> Cc: Pawel Moll <pawel.moll@arm.com> Cc: Mark Rutland <mark.rutland@arm.com> Cc: Stephen Warren <swarren@wwwdotorg.org> Cc: Ian Campbell <ian.campbell@citrix.com> Cc: devicetree@vger.kernel.org Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
I forgot to separete the different names in the reg-names property. This didn't cause anything to fail because the driver does not use the names and simply relies on the order of the memory offsets in reg. This patch fixes this in case it is used later. Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: NFelipe Balbi <balbi@ti.com>
-
- 27 8月, 2013 1 次提交
-
-
由 Boris BREZILLON 提交于
This patch describe the phy used on atmel sama5d3 mother board: - phy address - phy interrupt pin Signed-off-by: NBoris BREZILLON <b.brezillon@overkiz.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 8月, 2013 1 次提交
-
-
由 Qipan Li 提交于
the old codes defined uart0_nostreamctrl_pins, but missed pingroup and padmux definition for it. this patch fixes it. Signed-off-by: NQipan Li <Qipan.Li@csr.com> Signed-off-by: NBarry Song <Baohua.Song@csr.com> Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
-
- 22 8月, 2013 29 次提交
-
-
由 Jingchang Lu 提交于
enable i2c0 device on Vybrid VF610 Tower Board Signed-off-by: NJingchang Lu <b35083@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Alexander Shiyan 提交于
This adds one more I2C2 alternate pinmux entry. GPIO1_2 <=> SCL GPIO1_3 <=> SDA Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Alexander Shiyan 提交于
This unmix module/pin definitions and reduce indentation for pin groups, so makes template a bit cleaner. Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Peter Chen 提交于
USB OTG vbus pin needs to be configured as gpio function at sabresd board. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Peter Chen 提交于
We enabled USB host 1, so host 1's vbus should be on to let host 1 work. Signed-off-by: NPeter Chen <peter.chen@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Alexander Shiyan 提交于
Patch adds AUDMUX routing for Phytec PCM-038 module. This route i.MX SSI0 (Port 1) to the slave port 4 where MC13783 codec interface is connected. Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Alexander Shiyan 提交于
AUDMUX expects additional parameters to be configured correctly, so turn it off into a template. Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Tony Prisk 提交于
The wandboard has a Broadcom 4329 WiFi connected via SDIO. This patch sets the required pins to enable the wifi module. Signed-off-by: NTony Prisk <linux@prisktech.co.nz> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Alexander Shiyan 提交于
External high frequency clock CKIH1 is optional for i.MX51, so move it setup into boards where it is used. Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Fabio Estevam 提交于
mx53qsb uses GPIO7_8 to turn on VBUS, so add support for it. Also specify the PHY type in the device tree. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Tested-by: NArnaud Patard <arnaud.patard@rtp-net.org> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Philipp Zabel 提交于
This patch enables I2C1 and adds device tree nodes for the EEPROM and the DA9063 PMIC connected to this I2C bus. Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Philipp Zabel 提交于
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Fabio Estevam 提交于
mx6 sabresd boards have a egalax touchscreen controller connected via I2C3. Add support for it. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Add missing ocram gate clock for imx53 and also represent it in device tree ocram node. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
The ocram on imx6q is 256 KiB while on imx6dl it's 128 KiB. Let's have separate node for imx6q and imx6dl. It also changes imx6q size 0x3f000 to 0x40000 to match the hardware. Signed-off-by: NShawn Guo <shawn.guo@linaro.org> Acked-by: NLiu Ying <Ying.Liu@freescale.com>
-
由 Alexander Shiyan 提交于
Outputs regulator SW1A and SW1A, SW2A and SW2B are connected together, so it determined as "joined" operation for MC13783. Separate work of these outputs in this case would be wrong, so we define only one of the outputs. Additionally, define the full range of voltages for the CPU (1.2v - 1.52v). Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Alexander Shiyan 提交于
Clock name is not needed for "cpufreq-cpu0". Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Alexander Shiyan 提交于
i.MX27 CPU can be clocked with a 32 kHz quartz, and not just 32768 Hz, so increase "clock-latency" value, which will ensure that we use two clock cycles on frequency change. Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Alexander Shiyan 提交于
Add a label to i.MX27 CPU node. This change allows the reuse this node in the upper levels of the DTS. Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Alexander Shiyan 提交于
Patch removes optional "ptp" clock source for FEC. This clock is missing in i.MX27. Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Alexander Shiyan 提交于
Patch replaces "dummy" clock source for watchdog with "wdog_ipg_gate". Signed-off-by: NAlexander Shiyan <shc_work@mail.ru> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Fabio Estevam 提交于
This is useful for testing suspend/resume sequence. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
The CLKO is widely used by imx6q board designs to clock audio codec. Since most codecs accept 24 MHz frequency, let's initially set up CLKO with OSC24M (cko <-- cko2 <-- osc). Then those board specific CLKO setup for audio codec can be removed. The board dts files also need an update on cko reference in codec node. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Updates SSI nodes to adopt generic DMA bindings. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Add HannStar HSD100PXN1 XGA panel support on LVDS1 port of imx6qdl-sabresd board. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Fabio Estevam 提交于
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Fabio Estevam 提交于
Add support for the imx6q wanboard variant. Since imx6q/dl are pin to pin compatible, introduce the imx6qdl-wandboard.dtsi file that contains the common peripheral nodes. Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com> Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
Mark ocotp as a syscon node and add tempmon for imx6q thermal support. Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
-
由 Shawn Guo 提交于
After mxs-dma driver adopts generic DMA device tree binding, gpmi channel interrupt number is defined in DMA controller node, and channel ID is listed in "dmas" property. So the DMA channel interrupt number in gpmi node "interrupts" property and fsl,gpmi-dma-channel which are used by old customized DMA binding can be removed now. Signed-off-by: NShawn Guo <shawn.guo@linaro.org> Reviewed-by: NArnd Bergmann <arnd@arndb.de>
-