Cadhu have multiple power rails which are controlled by
GPIOs. Add support of these power rail control through
fixed regulators. Add entry for all fixed regulators for
cardhu-a02 and a04.
The details are taken from downstream kernel.

Some points on this change are:

* Add the tps65910-LDO5 entry and make it always ON
 to supply power to SDMMC. Once the sd driver support
 regulator handling, this flag will be remove.

* Dropping registration of rail vdd_sdmmc1 as the gpio
  is used by sdhci power-gpio. This need to fix in
  sdhci driver and then need to add the registration
  mechanism. Just removing power-gpio and adding fixed
  regulator with this gpio is causing the sd  access to
  fail because first probe call of this regulator fails
  due to non-available of parent and so it calls
  gpio_free() which disable the pins in gpio mode make
  pin output to LOW causes power to OFF. In probe retry,
  it got success and it powered-on but it again need to
  do again numeration of card here.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

There is multiple version of cardhu starting from A01 to A07.
Cardhu A01 and A03 are not supported. Cardhu A02 will have
different sets of GPIOs for fixed regulator compare to
cardhu A04. The Cardhu A05, A06, A07 are compatibe with A04.
Based on cardhu version, the related dts file need to be chosen
like for cardhu A02, use tegra30-cardhu-a02.dts, cardhu A04 and
more, use tegra30-cardhu-a04.dts.
This patch create the DTS file A02 and A04 and convert tegra30-cardhu.dts
as dts include file.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Tegra30 based platform "cardhu" have the power management
IC TPS65911 for the regulator.
Adding DT entry for this device.
Data are chosen from downstream kernel and making the
voltage output as require by default for device to
operate.
The default interrupt line is HIGH from PMIC device and so
inverting the interrupt detection line of PMU interrupt
through configuring PMC.
In this patch, do not registering LDO5 because the input
supply for this rail is different for different version of
cardhu i..e A02 and A04. The registration will be done once
the dts file for cardhu A02 and A04 are added in follow on
patches.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Using 'select' in Kconfig is hard, a platform cannot just
enable a driver without also making sure that its subsystem
is there. Also, there is no actual code dependency between
the platform and the gpio leds driver.

Without this patch, building without LEDS_CLASS esults in:

drivers/built-in.o: In function `create_gpio_led.part.2':
governor_userspace.c:(.devinit.text+0x5a58): undefined reference to `led_classdev_register'
drivers/built-in.o: In function `gpio_led_remove':
governor_userspace.c:(.devexit.text+0x6b8): undefined reference to `led_classdev_unregister'

This reverts 8733f53c "ARM: ux500: Kconfig: Compile in leds-gpio
support for Snowball" that introduced the regression and did not
provide a helpful explanation.

In order to leave the GPIO LED code still present in normal
builds, this also enables the symbol in u8500_defconfig, in addition
to the other LED drivers that are already selected there.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Lee Jones <lee.jones@linaro.org>

The head-v7.S contains a call to the generic cpu_suspend function,
which is only available when selected by the i.MX6 code. As
pointed out by Shawn Guo, i.MX5 does not actually use any
functions defined in head-v7.S. It is also needed only for
the i.MX6 power management code and for the SMP code, so
we can restrict building this file to situations in which
at least one of those two is present.

Finally, other platforms with a similar file call it headsmp.S,
so we can rename it to the same for consistency.

Without this patch, building imx5 standalone results in:

arch/arm/mach-imx/built-in.o: In function `v7_cpu_resume':
arch/arm/mach-imx/head-v7.S:104: undefined reference to `cpu_resume'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Eric Miao <eric.miao@linaro.org>
Cc: stable@vger.kernel.org

The i.MX cpufreq implementation uses the CPU_FREQ_TABLE helpers,
so it needs to select that code to be built. This problem has
apparently existed since the i.MX cpufreq code was first merged
in v2.6.37.

Building IMX without CPU_FREQ_TABLE results in:

arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_exit':
arch/arm/plat-mxc/cpufreq.c:173: undefined reference to `cpufreq_frequency_table_put_attr'
arch/arm/plat-mxc/built-in.o: In function `mxc_set_target':
arch/arm/plat-mxc/cpufreq.c:84: undefined reference to `cpufreq_frequency_table_target'
arch/arm/plat-mxc/built-in.o: In function `mxc_verify_speed':
arch/arm/plat-mxc/cpufreq.c:65: undefined reference to `cpufreq_frequency_table_verify'
arch/arm/plat-mxc/built-in.o: In function `mxc_cpufreq_init':
arch/arm/plat-mxc/cpufreq.c:154: undefined reference to `cpufreq_frequency_table_cpuinfo'
arch/arm/plat-mxc/cpufreq.c:162: undefined reference to `cpufreq_frequency_table_get_attr'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Yong Shen <yong.shen@linaro.org>
Cc: stable@vger.kernel.org

The ksz9021rn_phy_fixup and mx6q_sabrelite functions try to
set up an ethernet phy if they can. They do check whether
phylib is enabled, but unfortunately the functions can only
be called from platform code if phylib is builtin, not
if it is a module

Without this patch, building with a modular phylib results in:

arch/arm/mach-imx/mach-imx6q.c: In function 'imx6q_sabrelite_init':
arch/arm/mach-imx/mach-imx6q.c:120:5: error: 'ksz9021rn_phy_fixup' undeclared (first use in this function)
arch/arm/mach-imx/mach-imx6q.c:120:5: note: each undeclared identifier is reported only once for each function it appears in

The bug was originally reported by Artem Bityutskiy but only
partially fixed in ef441806 "ARM: imx6q: register phy fixup only when
CONFIG_PHYLIB is enabled".
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Cc: Sascha Hauer <s.hauer@pengutronix.de>

This moves the imx5 pm code out of the list of unconditionally
compiled files for imx5, mirroring what we already do for imx6
and how it was done before the code was move from mach-mx5 to
mach-imx in v3.3.

Without this patch, building with CONFIG_PM disabled results in:

arch/arm/mach-imx/pm-imx5.c:202:116: error: redefinition of 'imx51_pm_init'
arch/arm/mach-imx/include/mach-imx/common.h:154:91: note: previous definition of 'imx51_pm_init' was here
arch/arm/mach-imx/pm-imx5.c:209:116: error: redefinition of 'imx53_pm_init'
arch/arm/mach-imx/include/mach-imx/common.h:155:91: note: previous definition of 'imx53_pm_init' was here
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: stable@vger.kernel.org

The new omap4 cpuidle implementation currently requires
ARCH_NEEDS_CPU_IDLE_COUPLED, which only works on SMP.

This patch makes it possible to build a non-SMP kernel
for that platform. This is not normally desired for
end-users but can be useful for testing.

Without this patch, building rand-0y2jSKT results in:

drivers/cpuidle/coupled.c: In function 'cpuidle_coupled_poke':
drivers/cpuidle/coupled.c:317:3: error: implicit declaration of function '__smp_call_function_single' [-Werror=implicit-function-declaration]

It's not clear if this patch is the best solution for
the problem at hand. I have made sure that we can now
build the kernel in all configurations, but that does
not mean it will actually work on an OMAP44xx.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

The binding doc and dts use properties "fsl,{cd,wp}-internal" while
esdhc driver uses "fsl,{cd,wp}-controller".  Fix binding doc and dts
to get them match driver code.
Reported-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: NChris Ball <cjb@laptop.org>

Though commit 602bf409 (ARM: imx6: exit coherency when shutting down
a cpu) improves the stability of imx6q cpu hotplug a lot, there are
still hangs seen with a more stressful hotplug testing.

It's expected that once imx_enable_cpu(cpu, false) is called, the cpu
will be taken down by hardware immediately, and the code after that
will not get any chance to execute.  However, this is not always the
case from the testing.  The cpu could possibly be alive for a few
cycles before hardware actually takes it down.  So rather than letting
cpu execute some code that could cause a hang in these cycles, let's
make the cpu spin there and wait for hardware to take it down.

Cc: <stable@vger.kernel.org>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

Previous attempts to add platform probing of the Audio related devices
only call from non-DT initialisation functions. This patch extends that
functionality to the Device Tree related ones too.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The platform attempts to register platform device 'snd_soc_u8500'
which doesn't actually exist. Here we change the reference to the
correct one 'snd_soc_mop500'.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The ldb_di[01]_podf is implemented as a clk-divider that
divides by 1 or 2. In reality, the ldb_di[01]_ipu_div
dividers divide by either 3.5 or 7. Adding a fixed factor
of 1/3.5 fixes their children's clock rates.

This should probably be converted to rate table based dividers,
once available.

Cc: <stable@vger.kernel.org>
Signed-off-by: NPhilipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: NSteffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>

While building the dtbs target, one is getting:

make dtbs
make[1]: *** No rule to make target `arch/arm/boot/kirkwood-qnap-ts219.dtb', needed by `arch/arm/boot/dtbs'.  Stop.
make: *** [dtbs] Error 2

The reason is that there's no kirkwood-qnap-ts219.dts file. Update Makefile.boot
to reflect the dts files present.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

While converting, a led has been missed leading to wrong power blue led
definition. Add it back and fix the gpio used on the power blue led.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

The mv643xx ethernet controller limits the packet size for the TX
checksum offloading. This patch sets this limits for Kirkwood and
Dove which have smaller limits that the default.

As a side note, this patch is an updated version of a patch sent some years
ago: http://lists.infradead.org/pipermail/linux-arm-kernel/2010-June/017320.html
which seems to have been lost.
Signed-off-by: NArnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>
Cc: <stable@vger.kernel.org>

Seems that Thomas' and my patches collided during the last merge
window.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Patch b6d1c33a "ARM: Orion: Consolidate the address map setup" tried
to merge the address map for the four orion platforms, but apparently
got it wrong for mv78xx0. Admittedly I don't understand what this
code actually does, but it's clear that the current version is
wrong.

Without this patch, building mv78xx0_defconfig results in:

arch/arm/mach-mv78xx0/addr-map.c:59:2: warning: initialization from incompatible pointer type [enabled by default]
arch/arm/mach-mv78xx0/addr-map.c:59:2: warning: (near initialization for 'addr_map_cfg.win_cfg_base') [enabled by default]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Cc: Michael Walle <michael@walle.cc>
Cc: Nicolas Pitre <nico@linaro.org>

Calling omap_dm_timer_prepare while the spinlock is held is not
allowed as sleeping functions are called later on during the
preparation (namely within clk_get()).

dm_timer_lock is only required for protecting the
omap_timer_list. After the timer is marked as reserved, the lock is no
longer needed and should be freed.
Signed-off-by: NTimo Kokkonen <timo.t.kokkonen@iki.fi>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This partially reverts 357c9c1f
(ARM: Remove support for ARMv3 ARM610 and ARM710 CPUs).

Although we only support StrongARM on the RiscPC, we need to keep the
ARMv3 user access code for this platform because the bus does not
understand half-word load/stores.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 5a783cbc ("ARM: 7478/1: errata: extend workaround for erratum
 #720789") added workarounds for erratum #720789 to the range TLB
invalidation functions with the observation that the erratum only
affects SMP platforms. However, when running an SMP_ON_UP kernel on a
uniprocessor platform we must take care to preserve the ASID as the
workaround is not required.

This patch ensures that we don't set the ASID to 0 when flushing the TLB
on such a system, preserving the original behaviour with the workaround
disabled.

Cc: <stable@vger.kernel.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Page migration encodes the pfn in the offset field of a swp_entry_t.
For LPAE, we support physical addresses of up to 36 bits (due to
sparsemem limitations with the size of page flags), requiring 24 bits
to represent a pfn. A further 3 bits are used to encode a swp_entry into
a pte, leaving 5 bits for the type field. Furthermore, the core code
defines MAX_SWAPFILES_SHIFT as 5, so the additional type bit does not
get used.

This patch reduces the width of the type field to 5 bits, allowing us
to create up to 31 swapfiles of 64GB each.

Cc: <stable@vger.kernel.org>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Swap entries are encoding in ptes such that !pte_present(pte) and
pte_file(pte). The remaining bits of the descriptor are used to identify
the swapfile and offset within it to the swap entry.

When writing such a pte for a user virtual address, set_pte_at
unconditionally sets the nG bit, which (in the case of LPAE) will
corrupt the swapfile offset and lead to a BUG:

[  140.494067] swap_free: Unused swap offset entry 000763b4
[  140.509989] BUG: Bad page map in process rs:main Q:Reg  pte:0ec76800 pmd:8f92e003

This patch fixes the problem by only setting the nG bit for user
mappings that are actually present.

Cc: <stable@vger.kernel.org>
Reviewed-by: NCatalin Marinas <catalin.marinas@arm.com>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Many clocks that are used to provide sched_clock will reset during
suspend.  If read_sched_clock returns 0 after suspend, sched_clock will
appear to jump forward.  This patch resets cd.epoch_cyc to the current
value of read_sched_clock during resume, which causes sched_clock() just
after suspend to return the same value as sched_clock() just before
suspend.

In addition, during the window where epoch_ns has been updated before
suspend, but epoch_cyc has not been updated after suspend, it is unknown
whether the clock has reset or not, and sched_clock() could return a
bogus value.  Add a suspended flag, and return the pre-suspend epoch_ns
value during this period.

The new behavior is triggered by calling setup_sched_clock_needs_suspend
instead of setup_sched_clock.
Signed-off-by: NColin Cross <ccross@android.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Now that ARM has implemented its spinlocks with tickets we don't
need to use the generic lockbreak algorithm. Remove the Kconfig
from ARM so that we use the arch_spin_is_contended() definition
from the asm header. This also saves a word in each lock because
we don't need the break_lock member anymore.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

VFPv4 support depends on the VFPv3 context save/restore code, so only
advertise support in the hwcaps if the kernel can actually handle it.

Cc: <stable@vger.kernel.org> # 3.1+
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Get rid of this warning..
arch/arm/kernel/built-in.o(.text+0xac78): Section mismatch in reference
from the function init_cpu_topology() to the function
 .init.text:parse_dt_topology()
The function init_cpu_topology() references
the function __init parse_dt_topology().
This is often because init_cpu_topology lacks a __init
annotation or the annotation of parse_dt_topology is wrong.
Signed-off-by: NVenkatraman S <svenkatr@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix the wrong logic: we should use || instead of &&

Cc: Leo Yan <leoy@marvell.com>
Cc: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: NYuanhan Liu <yliu.null@gmail.com>
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>

ntosd2_init_i2c walks the ntosd2_i2c_info array, which it expects to
be populated with at least one member. gcc correctly warns about
the out-of-bounds access here.

Since this can not possibly work, it's better to disable i2c
support entirely on this board.

Without this patch, building davinci_all_defconfig results in:

arch/arm/mach-davinci/board-neuros-osd2.c: In function 'davinci_ntosd2_init':
arch/arm/mach-davinci/board-neuros-osd2.c:187:20: warning: array subscript is above array bounds [-Warray-bounds]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Andrey Porodko <panda@chelcom.ru>

Disabling CONFIG_BUG creates an insane amount of build warnings, which
makes it useless to check for building defconfigs to see if new
warnings show up.

Without this patch, building tct_hammer_defconfig results in:

net/packet/af_packet.c: In function 'tpacket_rcv':
net/packet/af_packet.c:1889:30: warning: 'hdrlen' may be used uninitialized in this function [-Wuninitialized]
net/core/ethtool.c: In function 'ethtool_get_feature_mask':
net/core/ethtool.c:213:1: warning: control reaches end of non-void function [-Wreturn-type]
block/cfq-iosched.c: In function 'cfq_async_queue_prio':
block/cfq-iosched.c:2914:1: warning: control reaches end of non-void function [-Wreturn-type]
mm/bootmem.c: In function 'mark_bootmem':
mm/bootmem.c:352:1: warning: control reaches end of non-void function [-Wreturn-type]
net/core/dev.c: In function 'skb_warn_bad_offload':
net/core/dev.c:1904:33: warning: unused variable 'null_features' [-Wunused-variable]
drivers/mtd/chips/cfi_probe.c: In function 'cfi_chip_setup':
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
include/linux/mtd/map.h:394:11: note: 'r.x[0]' was declared here
include/linux/mtd/cfi.h:489:3: warning: 'r.x[0]' may be used uninitialized in this function [-Wuninitialized]
(and many more)

The size of vmlinux increases by 1.78% because of this:

size obj-arm/vmlinux.nobug
   text    data     bss     dec     hex filename
   2108474  116916   55352 2280742  22cd26 obj-arm/vmlinux
size obj-arm/vmlinux.bug
   text    data     bss     dec     hex filename
   2150804  116916   53696 2321416  236c08 obj-arm/vmlinux
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Ben Dooks <ben-linux@fluff.org>

exynos_pm_add_dev_to_genpd is used if one or more out of a large
number of Kconfig symbols are enabled. However the new
exynos_defconfig selects none of those, so the function becomes
unused. Marking it so lets the compiler automatically discard
it.

Without this patch, building exynos_defconfig results in:

arch/arm/mach-exynos/pm_domains.c:118:123: warning: 'exynos_pm_add_dev_to_genpd' defined but not used [-Wunused-function]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>

The 4430 OPP table was being registered for all other OMAP4 variants
too, like 4460 and 4470 causing issues with cpufreq driver
enabled. 4460 and 4470 devices have different OPPs as compared to
4430, and they should be populated seperately. As long as that
happens, let the OPP table registeration happen only on 4430 device.
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

OMAP4 sleep entry code even though itself don't use many CPU registers
makes call to the v7_flush_dcache_all() which uses them. Since
v7_flush_dcache_all() doesn't make use of stack, the caller must take
care of the stack frame. Otherwise it will lead to corrupted stack frame.

Fix it by saving used registers.
Reported-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NKevin Hilman <khilman@ti.com>

It is not currently possible to build the gpmi-nand driver without
also building the mxs-dma driver. Clarify this Kconfig and enable
both in the defconfig file so we can build it again with both enabled.

drivers/built-in.o: In function `gpmi_dma_filter':
clk-fixed-factor.c:(.text+0xafc18): undefined reference to `mxs_dma_is_apbh'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NDirk Behme <dirk.behme@de.bosch.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Sascha Hauer <kernel@pengutronix.de>

Without this patch, building integrator_defconfig results in:

arch/arm/mach-integrator/core.c:150:1: warning: data definition has no type or storage class [enabled by default]
arch/arm/mach-integrator/core.c:150:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
arch/arm/mach-integrator/core.c:150:1: warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Cc: Russell King <linux@arm.linux.org.uk>

The samsung PWM driver has moved to the new PWM subsystem, which
changed the Kconfig symbol for that driver, but the rx1950 and
gta02 boards still uses the old one.

Without this patch, building s3c2410_defconfig results in:

arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_lcd_power':
arch/arm/mach-s3c24xx/mach-rx1950.c:430: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:431: undefined reference to `pwm_disable'
arch/arm/mach-s3c24xx/mach-rx1950.c:437: undefined reference to `pwm_config'
arch/arm/mach-s3c24xx/mach-rx1950.c:438: undefined reference to `pwm_enable'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_exit':
arch/arm/mach-s3c24xx/mach-rx1950.c:504: undefined reference to `pwm_free'
arch/arm/mach-s3c24xx/built-in.o: In function `rx1950_backlight_init':
arch/arm/mach-s3c24xx/mach-rx1950.c:487: undefined reference to `pwm_request'
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reported-by: NTushar Behera <tushar.behera@linaro.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>

The sa1100 definition of the io_p2v macro has changed in v3.6, and this one
file stopped working because of that.

Without this patch, building hackkit_defconfig results in:

arch/arm/mach-sa1100/leds-hackkit.c: In function 'hackkit_leds_event':
arch/arm/mach-sa1100/leds-hackkit.c:39:4: error: implicit declaration of function 'IOMEM' [-Werror=implicit-function-declaration]
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Russell King <linux@arm.linux.org.uk>

The EETI touchscreen asserts its IRQ line as soon as it has data in its
internal buffers. The line is automatically deasserted once all data has
been read via I2C. Hence, the driver has to monitor the GPIO line and
cannot simply rely on the interrupt handler reception.

In the current implementation of the driver, irq_to_gpio() is used to
determine the GPIO number from the i2c_client's IRQ value.

As irq_to_gpio() is not available on all platforms, this patch changes
this and makes the driver ignore the passed in IRQ. Instead, a GPIO is
added to the platform_data struct and gpio_to_irq is used to derive the
IRQ from that GPIO. If this fails, bail out. The driver is only able to
work in environments where the touchscreen GPIO can be mapped to an
IRQ.

Without this patch, building raumfeld_defconfig results in:

drivers/input/touchscreen/eeti_ts.c: In function 'eeti_ts_irq_active':
drivers/input/touchscreen/eeti_ts.c:65:2: error: implicit declaration of function 'irq_to_gpio' [-Werror=implicit-function-declaration]
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: stable@vger.kernel.org (v3.2+)
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Sven Neumann <s.neumann@raumfeld.com>
Cc: linux-input@vger.kernel.org
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>

Commit 3d55c29f "ARM: tegra: harmony: add regulator supply name and its
input supply" was supposed to fix all the problems with regulators on
Harmony. However, it appears that I only tested it when booting using
board files, not when booting using device tree. This change fixes two
problems with regulators when booting using device tree:

1) That patch only created the vdd_sys regulator when booting using a
   board file. Since this is the root of the whole regulator tree, this
   caused no regulators to successfully initialize when booting using
   device tree. The registration of vdd_sys is moved to fix this.

2) When booting use DT, the regulator core sets has_full_constraints,
   which in turn causes the core to turn off any regulators not marked
   as always on. Some of the affected regulators are required for basic
   system operation. To solve this, add always on constraints to all
   relevant regulators. This doesn't affect booting using a board file
   since nothing sets has_full_constraints in that case.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>