- 29 7月, 2009 18 次提交
-
-
由 Sarah Sharp 提交于
The 0.95 xHCI specification requires software to set the "TD size" field in each transaction request block (TRB). This field gives the host controller an indication of how much data is remaining in the TD (including the buffer in the current TRB). Set this field in bulk TRBs and data stage TRBs for control transfers. Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Roel Kluin 提交于
Without this change the loops won't start Signed-off-by: NRoel Kluin <roel.kluin@gmail.com> Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Alan Stern 提交于
THis patch (as1270) allows the usbtest module to be built even when USB_DEVICEFS isn't configured. Tests can be performed without USB_DEVICEFS, using the /dev/bus/usb/*/* device files. Signed-off-by: NAlan Stern <stern@rowland.harvard.edu> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Ajay Kumar Gupta 提交于
INDEX register has to be set to '0' before reading CONFIGDATA register which is only present in TI musb platforms. Currently the default register access mode is set to FLAT_MODE thus INDEX register is not getting set properly with musb_ep_select() which is just a nop operation in FLAT_MODE.This invalid register read is causing module reinset failure. Fixing the issue by moving INDEX register write part to musb_read_configdata() function itself. Signed-off-by: NVikram Pandita <vikram.pandita@ti.com> Signed-off-by: NAnand Gadiyar <gadiyar@ti.com> Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com> Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Amit Kucheria 提交于
musb_otg_timer_func() is defined under #ifdef CONFIG_USB_MUSB_OTG. Make sure any reference to it is also under the same #ifdef. Without this fix, the driver failes to compile when USB_OTG is defined but USB_MUSB_OTG isn't. Signed-off-by: NAmit Kucheria <amit.kucheria@canonical.com> Cc: Felipe Balbi <felipe.balbi@nokia.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Sergei Shtylyov 提交于
This function uses wrong bit mask to prevent clearing RXCSR status bits when halting an endpoint -- which results in clearing SentStall and RxPktRdy bits (that the code actually tries to avoid); must be a result of cut-and-paste... Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Acked-by: NDavid Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Javier Martin 提交于
Added support for the Alcatel X060S/X200 broadband modems to the option driver. The device starts in cd-rom emulation mode (1bbb:f000) and requires the use of the usb_modeswitch tool to switch it to modem mode (1bbb:0000). Signed-off-by: NJavier Martin <jmartinj@iname.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Peng Huang 提交于
Signed-off-by: NPeng Huang <shawn.p.huang@gmail.com> Cc: Jiri Kosina <jkosina@suse.cz> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Russell Lang 提交于
I've opened up the case, and the chips in the ATEN UC2324 are: Moschip MCS7840CV-AA 69507-6B1 0650 (USB to 4-port serial) (logo with AF kerned together) 0748 24BC02 SINGLP (unknown 8-pin chip) (logo looks like 3 or Z in circle) ZT3243LEEA 0752 B7A16420.T (4 chips, so this will be RS232 line driver) (Probably equivalent of Sipex SP3243) So the ATEN 2324 (aten2011.c driver), is definitely the Moschip 7840, and should use the mos7840.c driver. I expect you will remove the aten2011.c driver from the staging area. From the aten2011.c source code, the device ID for the UC2322 (2 port serial) is 0x7820, just like the Moschip evaluation board. This value should be added to the device id table of mos7840.c. Here's a patch that adds these devices to the driver. From: Russell Lang <gsview@ghostgum.com.au> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Tim Gardner 提交于
BugLink: https://bugs.launchpad.net/bugs/365291Signed-off-by: NTim Gardner <tim.gardner@canonical.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
Current listed Onda ids are ZTE devices. Replace them with ZTE id define and add more ZTE device ids. Also remove 19d2:2000, this is the id when device is first plugged in and is a CD-only device, before the switch using eject. These changes are based on a previous patch by Ming Zhao <zhao.ming9@zte.com.cn> Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br> Cc: Ming Zhao <zhao.ming9@zte.com.cn> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Simon Kagstrom 提交于
I noticed that USB initialization didn't setup correctly on my kirkwood based board (OpenRD base) if I hadn't initialized USB in U-boot first. The error message looks like this: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver orion-ehci orion-ehci.0: Marvell Orion EHCI orion-ehci orion-ehci.0: new USB bus registered, assigned bus number 1 orion-ehci orion-ehci.0: can't setup orion-ehci orion-ehci.0: USB bus 1 deregistered orion-ehci orion-ehci.0: init orion-ehci.0 fail, -110 orion-ehci: probe of orion-ehci.0 failed with error -110 which is caused by ehci_halt() timing out in the handshake() call. I noticed that U-boot does a reset before calling handshake(), so this patch does the same thing for Linux. USB now works for me. Signed-off-by: NSimon Kagstrom <simon.kagstrom@netinsight.net> Acked-by: NNicolas Pitre <nico@marvell.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Craig Shelley 提交于
Signed-off-by: NCraig Shelley <craig@microtron.org.uk> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Ville Sundberg 提交于
The patch adds support for the GN Otometrics Aurical USB Audiometer (FT232BM-based). A new VID and a new PID is added. Signed-off-by: NVille Sundberg <vsundber@gmail.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Anand Gadiyar 提交于
OMAP: OHCI: hc_driver's stop method should call ohci_stop Without this, the ohci-omap driver will not cleanup the debugfs nodes when the driver is unloaded. So the next insmod will fail, if CONFIG_DEBUG_FS and CONFIG_USB_DEBUG are both selected. Reported-by: Nvikram pandita <vikram.pandita@ti.com> Cc: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: NAnand Gadiyar <gadiyar@ti.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Giacomo Lozito 提交于
Requests to get max LUN, for certain USB storage devices, require a longer timeout before a correct reply is returned. This happens for a Realtek USB Card Reader (0bda:0152), which has a max LUN of 3 but is set to 0, thus losing functionality, because of the timeout occurring too quickly. Raising the timeout value fixes the issue and might help other devices to return a correct max LUN value as well. Signed-off-by: NGiacomo Lozito <james@develia.org> Acked-by: NAlan Stern <stern@rowland.harvard.edu> Cc: stable <stable@kernel.org> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Oliver Neukum 提交于
This is needed for compilation without CONFIG_PM. Signed-off-by: NOliver Neukum <oliver@neukum.org> Acked-by: NRandy Dunlap <randy.dunlap@oracle.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
由 Carlos R. Mafra 提交于
After commit f092c240 ("USB: option: remove unnecessary and erroneous code") the variable 'serial' becomes unused, as gcc-4.3.2 points out: drivers/usb/serial/option.c: In function 'option_instat_callback': drivers/usb/serial/option.c:834: warning: unused variable 'serial' drivers/usb/serial/option.c: In function 'option_open': drivers/usb/serial/option.c:930: warning: unused variable 'serial' So I removed it. Signed-off-by: NCarlos R. Mafra <crmafra@aei.mpg.de> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 28 7月, 2009 21 次提交
-
-
由 Benjamin Herrenschmidt 提交于
Those definitions are already provided by asm-generic Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: NPaul Mundt <lethal@linux-sh.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Alan Cox 提交于
This fixes - locking bug that was hidden by ecc2e05e - Regression #13821 - Spurious warning when closing and blocking for data write out With these changes my PL2303 always ends up as ttyUSB0 when it should and the module refcounts stay correct. I'll do a more wholesale split & tidy of _open in the next release or two as we get a standard tty_port_open and port->ops->init port->ops->shutdown call backs. Copy sent to Alan Stern and Carlos Mafra just to confirm it fixes all the reports but it passes local testing with the same hardware as Alan Stern. Signed-off-by: NAlan Cox <alan@linux.intel.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.infradead.org/users/eparis/notify由 Linus Torvalds 提交于
* 'for-linus' of git://git.infradead.org/users/eparis/notify: inotify: use GFP_NOFS under potential memory pressure fsnotify: fix inotify tail drop check with path entries inotify: check filename before dropping repeat events fsnotify: use def_bool in kconfig instead of letting the user choose inotify: fix error paths in inotify_update_watch inotify: do not leak inode marks in inotify_add_watch inotify: drop user watch count when a watch is removed
-
由 Alan Cox 提交于
This also makes close stall in the normal case which is apparently needed to fix emacs Signed-off-by: NAlan Cox <alan@linux.intel.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits) cnic: Fix ISCSI_KEVENT_IF_DOWN message handling. net: irda: init spinlock after memcpy ixgbe: fix for 82599 errata marking UDP checksum errors r8169: WakeOnLan fix for the 8168 netxen: reset ring consumer during cleanup net/bridge: use kobject_put to release kobject in br_add_if error path smc91x.h: add config for Nomadik evaluation kit NET: ROSE: Don't use static buffer. eepro: Read buffer overflow tokenring: Read buffer overflow at1700: Read buffer overflow fealnx: Write outside array bounds ixgbe: remove unnecessary call to device_init_wakeup ixgbe: Don't priority tag control frames in DCB mode ixgbe: Enable FCoE offload when DCB is enabled for 82599 net: Rework mdio-ofgpio driver to use of_mdio infrastructure register at91_ether using platform_driver_probe skge: Enable WoL by default if supported net: KS8851 needs to depend on MII be2net: Bug fix in the non-lro path. Size of received packet was not updated in statistics properly. ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp: amd64_edac: read the right F2 maskoffset reg
-
由 Alan Cox 提交于
The port lock is used to protect the port state. However the port structure is freed on a hangup, then the lock taken on a close. The right fix is to drop the port on tty->shutdown() but we can't yet do that due to sleep v non-sleeping rules. Instead do the next best thing and fix it up when we are not in -rc season. Reported-by: NDaniel Mack <daniel@caiaq.de> Signed-off-by: NAlan Cox <alan@linux.intel.com> Tested-by: NDaniel Mack <daniel@caiaq.de> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.monstr.eu/linux-2.6-microblaze由 Linus Torvalds 提交于
* 'fixes-for-linus' of git://git.monstr.eu/linux-2.6-microblaze: microblaze: Makefile cleanup microblaze: Typo fix for cpu param inconsistency microblaze: Add support for R_MICROBLAZE_64_NONE microblaze: Get module loading working microblaze: remove sys_ipc microblaze: Support unaligned address for put/get_user macros microblaze: Detect new Microblaze 7.20 versions microblaze: Fix do_page_fault for no context microblaze: Add _PAGE_FILE macros to pgtable.h microblaze: Fix put_user macro for 64bits arguments microblaze: Clear print messages for DTB passing via r7 microblaze: Not to clear r7 after copying DTB to kernel microblaze: Add messages about FDT blob microblaze: Final support for statically linked DTB microblaze: remove duplicated #include microblaze: Define tlb_flush macro
-
由 Linus Torvalds 提交于
Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip * 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: x86: geode: Mark mfgpt irq IRQF_TIMER to prevent resume failure x86, amd: Don't probe for extended APIC ID if APICs are disabled x86, mce: Rename incorrect macro name "CONFIG_X86_THRESHOLD" x86-64: Fix bad_srat() to clear all state x86, mce: Fix set_trigger() accessor x86: Fix movq immediate operand constraints in uaccess.h x86: Fix movq immediate operand constraints in uaccess_64.h x86: Add reboot fixup for SBC-fitPC2 x86: Include all of .data.* sections in _edata on 64-bit x86: Add quirk for Intel DG45ID board to avoid low memory corruption
-
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6: ALSA: hda - Fix mute control with some ALC262 models ALSA: snd_usb_caiaq: add support for Audio2DJ ALSA: pcm - Fix hwptr buffer-size overlap bug ALSA: pcm - Fix warnings in debug loggings ALSA: pcm - Add logging of hwptr updates and interrupt updates ASoC: tlv320aic3x: Enable PLL when not bypassed ALSA: hda - Restore GPIO1 properly at resume with AD1984A ALSA: ctxfi - Fix uninitialized error checks ALSA: hda - Use snprintf() to be safer ALSA: usb-audio - Volume control quirk for QuickCam E 3500 ALSA: pcm - Fix regressions with VMware
-
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6由 Linus Torvalds 提交于
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6: (34 commits) V4L/DVB (12303): cx23885: check pointers before dereferencing in dprintk macro V4L/DVB (12302): cx23885-417: fix broken IOCTL handling V4L/DVB (12300): bttv: fix regression: tvaudio must be loaded before tuner V4L/DVB (12291): b2c2: fix frontends compiled into kernel V4L/DVB (12286): sn9c20x: reorder includes to be like other drivers V4L/DVB (12284): gspca - jpeg subdrivers: Check the result of kmalloc(jpeg header). V4L/DVB (12283): gspca - sn9c20x: New subdriver for sn9c201 and sn9c202 bridges. V4L/DVB (12282): gspca - main: Support for vidioc_g_chip_ident and vidioc_g/s_register. V4L/DVB (12269): af9013: auto-detect parameters in case of garbage given by app V4L/DVB (12267): gspca - sonixj: Bad sensor init of non ov76xx sensors. V4L/DVB (12265): em28xx: fix tuning problem in HVR-900 (R1) V4L/DVB (12263): em28xx: set demod profile for Pinnacle Hybrid Pro 320e V4L/DVB (12262): em28xx: Make sure the tuner is initialized if generic empia USB id was used V4L/DVB (12261): em28xx: set GPIO properly for Pinnacle Hybrid Pro analog support V4L/DVB (12260): em28xx: make support work for the Pinnacle Hybrid Pro (eb1a:2881) V4L/DVB (12258): em28xx: fix typo in mt352 init sequence for Terratec Cinergy T XS USB V4L/DVB (12257): em28xx: make tuning work for Terratec Cinergy T XS USB (mt352 variant) V4L/DVB (12245): em28xx: add support for mt9m001 webcams V4L/DVB (12244): em28xx: adjust vinmode/vinctl based on the stream input format V4L/DVB (12243): em28xx: allow specifying sensor xtal frequency ...
-
git://git390.marist.edu/pub/scm/linux-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6: [S390] zcrypt: fix scheduling of hrtimer ap_poll_timer [S390] vdso: clock_gettime of CLOCK_THREAD_CPUTIME_ID with noexec=on [S390] vdso: fix per cpu area allocation [S390] hibernation: fix register corruption on machine checks [S390] hibernation: fix lowcore handling
-
git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-2.6-dm: dm table: pass correct dev area size to device_area_is_valid dm: remove queue next_ordered workaround for barriers dm raid1: wake kmirrord when requeueing delayed bios after remote recovery
-
git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/shaggy/jfs-2.6: jfs: Fix early release of acl in jfs_get_acl
-
由 Oleg Nesterov 提交于
Commit 63706172 ("kthreads: rework kthread_stop()") removed the limitation that the thread function mysr not call do_exit() itself, but forgot to update the comment. Since that commit it is OK to use kthread_stop() even if kthread can exit itself. Signed-off-by: NOleg Nesterov <oleg@redhat.com> Signed-off-by: NRusty Russell <rusty@rustcorp.com.au> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Mike Frysinger 提交于
The check_modstruct_version() needs to look up the symbol "module_layout" in the kernel, but it does so literally and not by a C identifier. The trouble is that it does not include a symbol prefix for those ports that need it (like the Blackfin and H8300 port). So make sure we tack on the MODULE_SYMBOL_PREFIX define to the front of it. Signed-off-by: NMike Frysinger <vapier@gentoo.org> Signed-off-by: NRusty Russell <rusty@rustcorp.com.au> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6由 Linus Torvalds 提交于
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs-2.6: jbd: fix race between write_metadata_buffer and get_write_access ext3: Get rid of extenddisksize parameter of ext3_get_blocks_handle() jbd: Fix a race between checkpointing code and journal_get_write_access() ext3: Fix truncation of symlinks after failed write jbd: Fail to load a journal if it is too short
-
git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6: [CIFS] fix sparse warning cifs: fix sb->s_maxbytes so that it casts properly to a signed value cifs: disable serverino if server doesn't support it
-
由 Benjamin Herrenschmidt 提交于
mm: Pass virtual address to [__]p{te,ud,md}_free_tlb() Upcoming paches to support the new 64-bit "BookE" powerpc architecture will need to have the virtual address corresponding to PTE page when freeing it, due to the way the HW table walker works. Basically, the TLB can be loaded with "large" pages that cover the whole virtual space (well, sort-of, half of it actually) represented by a PTE page, and which contain an "indirect" bit indicating that this TLB entry RPN points to an array of PTEs from which the TLB can then create direct entries. Thus, in order to invalidate those when PTE pages are deleted, we need the virtual address to pass to tlbilx or tlbivax instructions. The old trick of sticking it somewhere in the PTE page struct page sucks too much, the address is almost readily available in all call sites and almost everybody implemets these as macros, so we may as well add the argument everywhere. I added it to the pmd and pud variants for consistency. Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: David Howells <dhowells@redhat.com> [MN10300 & FRV] Acked-by: NNick Piggin <npiggin@suse.de> Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [s390] Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Michael Chan 提交于
When a net device goes down or when the bnx2i driver is unloaded, the code was not generating the ISCSI_KEVENT_IF_DOWN message properly and this could cause the userspace driver to crash. This is fixed by sending the message properly in the shutdown path. cnic_uio_stop() is also added to send the message when bnx2i is unregistering. Signed-off-by: NMichael Chan <mchan@broadcom.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Deepak Saxena 提交于
irttp_dup() copies a tsap_cb struct, but does not initialize the spinlock in the new structure, which confuses lockdep. Signed-off-by: NDeepak Saxena <dsaxena@mvista.com> Signed-off-by: NIngo Molnar <mingo@elte.hu> Signed-off-by: NThomas Gleixner <tglx@linutronix.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 27 7月, 2009 1 次提交
-
-
由 onewayforever 提交于
Signed-off-by: Wan Wei <onewayforever@gmail.com> Signed-off-by: NBorislav Petkov <borislav.petkov@amd.com>
-