Define a station chandef, to be used for wider-bw TDLS peers. When both
peers support the feature, upgrade the channel bandwidth to the maximum
allowed by both peers and regulatory. Currently widths up to 80MHz are
supported in the 5GHz band.

When a TDLS peer connects/disconnects recalculate the channel type of the
current chanctx.
Make the chanctx width calculation consider wider-bw TDLS peers and
similarly fix the max_required_bw calculation for the chanctx min_def.
Since the sta->bandwidth is calculated only later on, take
bss_conf.chandef.width as the minimal width for station interface.

Set the upgraded channel width in the VHT-operation set during TDLS setup.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow a device to specify support for the TDLS wider-bandwidth feature.
Indicate this support during TDLS setup in the ext-capab IE and set an
appropriate station flag when our TDLS peer supports it.
This feature gives TDLS peers the ability to use a wider channel than
the base width of the BSS. For instance VHT capable TDLS peers connected
on a 20MHz channel can extend the channel to 80MHz, if regulatory
considerations allow it.

Do not cap the bandwidth of such stations by the current BSS channel width
in mac80211.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are now a fairly large number of mesh fields that really
aren't needed in any other modes; move those into their own
structure and allocate them separately.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, the station hash table lookup (or iteration) must
access two cachelines for each station - the one with the hash
table node, and the one with the MAC address.

Duplicate the MAC address next to the hash node to get rid of
this. Since the MAC address is static there's no consistency
problem introduced by this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are no RX queues in mac80211 (yet), the comment should refer
to the TID (including one slot for non-QoS) rather than 'RX queue'.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This struct member is only assigned, never used otherwise;
remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In mesh mode there is a race between establishing links and processing
rates and capabilities in beacons. This is very noticeable with slow
beacons (e.g. beacon intervals of 1s) and manifested for us as stations
using minstrel when minstrel_ht should be used. Fixed by changing
mesh_sta_info_init so that it always checks rates and such if it has not
already done so.
Signed-off-by: NAlexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This was missed in the previous patch, add some documentation
for rate_ctrl_lock to avoid docbook warnings.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This counter is unsafe with concurrent TX and is only exposed
through debugfs and ethtool. Instead of trying to fix it just
remove it for now, if it's really needed then it should be
exposed through nl80211 and in a way that drivers that do the
fragmentation in the device could support it as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When crypto is offloaded then in some cases it's all handled
by the device, and in others only some space for the IV must
be reserved in the frame. Handle both of these cases in the
fast-xmit path, up to a limit of 18 bytes of space for IVs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In order to speed up mac80211's TX path, add the "fast-xmit" cache
that will cache the data frame 802.11 header and other data to be
able to build the frame more quickly. This cache is rebuilt when
external triggers imply changes, but a lot of the checks done per
packet today are simplified away to the check for the cache.

There's also a more detailed description in the code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Both minstrel (reported by Sven Eckelmann) and the iwlwifi rate
control aren't properly taking concurrency into account. It's
likely that the same is true for other rate control algorithms.

In the case of minstrel this manifests itself in crashes when an
update and other data access are run concurrently, for example
when the stations change bandwidth or similar. In iwlwifi, this
can cause firmware crashes.

Since fixing all rate control algorithms will be very difficult,
just provide locking for invocations. This protects the internal
data structures the algorithms maintain.

I've manipulated hostapd to test this, by having it change its
advertised bandwidth roughly ever 150ms. At the same time, I'm
running a flood ping between the client and the AP, which causes
this race of update vs. get_rate/status to easily happen on the
client. With this change, the system survives this test.
Reported-by: NSven Eckelmann <sven@open-mesh.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The mesh plink code uses sta->lock to serialize access to the
plink state fields between the peer link state machine and the
peer link timer.  Some paths (e.g. those involving
mps_qos_null_tx()) unfortunately hold this spinlock across
frame tx, which is soon to be disallowed.  Add a new spinlock
just for plink access.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This allows drivers to request per-vif and per-sta-tid queues from which
they can pull frames. This makes it easier to keep the hardware queues
short, and to improve fairness between clients and vifs.

The task of scheduling packet transmission is left up to the driver -
queueing is controlled by mac80211. Drivers can only dequeue packets by
calling ieee80211_tx_dequeue. This makes it possible to add active queue
management later without changing drivers using this code.

This can also be used as a starting point to implement A-MSDU
aggregation in a way that does not add artificially induced latency.
Signed-off-by: NFelix Fietkau <nbd@openwrt.org>
[resolved minor context conflict, minor changes, endian annotations]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's an issue with the way the RX A-MPDU reorder timer is
deleted that can cause a kernel crash like this:

 * tid_rx is removed - call_rcu(ieee80211_free_tid_rx)
 * station is destroyed
 * reorder timer fires before ieee80211_free_tid_rx() runs,
   accessing the station, thus potentially crashing due to
   the use-after-free

The station deletion is protected by synchronize_net(), but
that isn't enough -- ieee80211_free_tid_rx() need not have
run when that returns (it deletes the timer.) We could use
rcu_barrier() instead of synchronize_net(), but that's much
more expensive.

Instead, to fix this, add a field tracking that the session
is being deleted. In this case, the only re-arming of the
timer happens with the reorder spinlock held, so make that
code not rearm it if the session is being deleted and also
delete the timer after setting that field. This ensures the
timer cannot fire after ___ieee80211_stop_rx_ba_session()
returns, which fixes the problem.

Cc: stable@vger.kernel.org
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We currently have a hand-rolled table with 256 entries and are
using the last byte of the MAC address as the hash. This hash
is obviously very fast, but collisions are easily created and
we waste a lot of space in the common case of just connecting
as a client to an AP where we just have a single station. The
other common case of an AP is also suboptimal due to the size
of the hash table and the ease of causing collisions.

Convert all of this to use rhashtable with jhash, which gives
us the advantage of a far better hash function (with random
perturbation to avoid hash collision attacks) and of course
that the hash table grows and shrinks dynamically with chain
length, improving both cases above.

Use a specialised hash function (using jhash, but with fixed
length) to achieve better compiler optimisation as suggested
by Sergey Ryazanov.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Revert commit ad38bfc9 ("mac80211: Tx frame latency statistics")
(along with some follow-up fixes).

This code turned out not to be as useful in the current form as we
thought, and we've internally hacked it up more, but that's not
very suitable for upstream (for now), and we might just do that
with tracing instead.

Therefore, for now at least, remove this code. We might also need
to use the skb->tstamp field for the TCP performance issue, which
is more important than the debugging.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement the new counters cfg80211 can now advertise to userspace.
The TX code is in the sequence number handler, which is a bit odd,
but that place already knows the TID and frame type, so it was
easiest and least impact there.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In TDLS (e.g., TDLS off-channel) there is a requirement for
some drivers to supply an unused TID between the AP and the
device to the FW, to allow sending PTI requests and to allow
the FW to aggregate on a specific TID for better throughput.

To ensure that the allocated TID is indeed unused, this patch
introduces an API for blocking the driver from TXing on that
TID.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Implement the cfg80211 TDLS channel switch ops and introduce new mac80211
ones for low-level drivers.
Verify low-level driver support for the new ops when using the relevant
wiphy feature bit. Also verify the peer supports channel switching before
passing the command down.

Add a new STA flag to track the off-channel state with the TDLS peer and
make sure to cancel the channel-switch if the peer STA is unexpectedly
removed.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The AP or peer can prohibit TDLS channel switch via a bit in the
extended capabilities IE. Parse the IE and track this bit. Set an
appropriate STA flag if both the AP and peer STA support TDLS
channel-switching.

Add the new STA flag and the missing TDLS_INITIATOR to debugfs.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Forgot to add an entry to the struct description of sta_info.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Reviewed-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Adding a timeout for tearing down a TDLS connection that
hasn't had ACKed traffic sent through it for a certain
amount of time.

Since we have no other monitoring facility to indicate the
existance (or non-existance) of a peer, this patch will
cause a peer to be considered as unavailable if for some X
time at least some Y packets have all not been ACKed.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When starting an offloaded BA session it is
unknown what starting sequence number should be
used. Using last_seq worked in most cases except
after hw restart.

When hw restart is requested last_seq is
(rightfully so) kept unmodified. This ended up
with BA sessions being restarted with an aribtrary
BA window values resulting in dropped frames until
sequence numbers caught up.

Instead of last_seq pick seqno of a first Rxed
frame of a given BA session.

This fixes stalled traffic after hw restart with
offloaded BA sessions (currently only ath10k).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We currently track the QoS capability twice: for all peer stations
in the WLAN_STA_WME flag, and for any clients associated to an AP
interface separately for drivers in the sta->sta.wme field.

Remove the WLAN_STA_WME flag and track the capability only in the
driver-visible field, getting rid of the limitation that the field
is only valid in AP mode.
Reviewed-by: NArik Nemtsov <arik@wizery.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Some drivers (e.g. ath10k) report A-MSDU subframes
individually with identical seqno. The A-MPDU Rx
reorder code did not account for that which made
it practically unusable with drivers using
RX_FLAG_AMSDU_MORE because it would end up
dropping a lot of frames resulting in confusion in
upper network transport layers.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Infer the TDLS initiator and track it in mac80211 via a STA flag. This
avoids breaking old userspace that doesn't pass it via nl80211 APIs.

The only case where userspace will need to pass the initiator is when the
STA is removed due to unreachability before a teardown packet is sent.
Support for unreachability was only recently added to wpa_supplicant, so
it won't be a problem in practice.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, cfg80211 tries to implement ethtool, but that doesn't
really scale well, with all the different operations. Make the
lower-level driver responsible for it, which currently only has
an effect on mac80211. It will similarly not scale well at that
level though, since mac80211 also has many drivers.

To cleanly implement this in mac80211, introduce a new file and
move some code to appropriate places.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Since WEP is practically dead, there seems very little
point in keeping WEP weak IV accounting.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The mesh_plink code is doing some interesting things with the
ignore_plink_timer flag.  It seems the original intent was to
handle this race:

cpu 0                           cpu 1
-----                           -----
                                start timer handler for state X
acquire sta_lock
change state from X to Y
mod_timer() / del_timer()
release sta_lock
                                acquire sta_lock
                                execute state Y timer too soon

However, using the mod_timer()/del_timer() return values to
detect these cases is broken.  As a result, timers get ignored
unnecessarily, and stations can get stuck in the peering state
machine.

Instead, we can detect the case by looking at the timer expiration.
In the case of del_timer, just ignore the timers in the following
(LISTEN/ESTAB) states since they won't have timers anyway.
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

It is currently possible to have a race due to the station PS
unblock work like this:
 * station goes to sleep with frames buffered in the driver
 * driver blocks wakeup
 * station wakes up again
 * driver flushes/returns frames, and unblocks, which schedules
   the unblock work
 * unblock work starts to run, and checks that the station is
   awake (i.e. that the WLAN_STA_PS_STA flag isn't set)
 * we process a received frame with PM=1, setting the flag again
 * ieee80211_sta_ps_deliver_wakeup() runs, delivering all frames
   to the driver, and then clearing the WLAN_STA_PS_DRIVER and
   WLAN_STA_PS_STA flags

In this scenario, mac80211 will think that the station is awake,
while it really is asleep, and any TX'ed frames should be filtered
by the device (it will know that the station is sleeping) but then
passed to mac80211 again, which will not buffer it either as it
thinks the station is awake, and eventually the packets will be
dropped.

Fix this by moving the clearing of the flags to exactly where we
learn about the situation. This creates a problem of reordering,
so introduce another flag indicating that delivery is being done,
this new flag also queues frames and is cleared only while the
spinlock is held (which the queuing code also holds) so that any
concurrent delivery/TX is handled correctly.
Reported-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There is a race between the TX path and the STA wakeup: while
a station is sleeping, mac80211 buffers frames until it wakes
up, then the frames are transmitted. However, the RX and TX
path are concurrent, so the packet indicating wakeup can be
processed while a packet is being transmitted.

This can lead to a situation where the buffered frames list
is emptied on the one side, while a frame is being added on
the other side, as the station is still seen as sleeping in
the TX path.

As a result, the newly added frame will not be send anytime
soon. It might be sent much later (and out of order) when the
station goes to sleep and wakes up the next time.

Additionally, it can lead to the crash below.

Fix all this by synchronising both paths with a new lock.
Both path are not fastpath since they handle PS situations.

In a later patch we'll remove the extra skb queue locks to
reduce locking overhead.

BUG: unable to handle kernel
NULL pointer dereference at 000000b0
IP: [<ff6f1791>] ieee80211_report_used_skb+0x11/0x3e0 [mac80211]
*pde = 00000000
Oops: 0000 [#1] SMP DEBUG_PAGEALLOC
EIP: 0060:[<ff6f1791>] EFLAGS: 00210282 CPU: 1
EIP is at ieee80211_report_used_skb+0x11/0x3e0 [mac80211]
EAX: e5900da0 EBX: 00000000 ECX: 00000001 EDX: 00000000
ESI: e41d00c0 EDI: e5900da0 EBP: ebe458e4 ESP: ebe458b0
 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068
CR0: 8005003b CR2: 000000b0 CR3: 25a78000 CR4: 000407d0
DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
DR6: ffff0ff0 DR7: 00000400
Process iperf (pid: 3934, ti=ebe44000 task=e757c0b0 task.ti=ebe44000)
iwlwifi 0000:02:00.0: I iwl_pcie_enqueue_hcmd Sending command LQ_CMD (#4e), seq: 0x0903, 92 bytes at 3[3]:9
Stack:
 e403b32c ebe458c4 00200002 00200286 e403b338 ebe458cc c10960bb e5900da0
 ff76a6ec ebe458d8 00000000 e41d00c0 e5900da0 ebe458f0 ff6f1b75 e403b210
 ebe4598c ff723dc1 00000000 ff76a6ec e597c978 e403b758 00000002 00000002
Call Trace:
 [<ff6f1b75>] ieee80211_free_txskb+0x15/0x20 [mac80211]
 [<ff723dc1>] invoke_tx_handlers+0x1661/0x1780 [mac80211]
 [<ff7248a5>] ieee80211_tx+0x75/0x100 [mac80211]
 [<ff7249bf>] ieee80211_xmit+0x8f/0xc0 [mac80211]
 [<ff72550e>] ieee80211_subif_start_xmit+0x4fe/0xe20 [mac80211]
 [<c149ef70>] dev_hard_start_xmit+0x450/0x950
 [<c14b9aa9>] sch_direct_xmit+0xa9/0x250
 [<c14b9c9b>] __qdisc_run+0x4b/0x150
 [<c149f732>] dev_queue_xmit+0x2c2/0xca0

Cc: stable@vger.kernel.org
Reported-by: NYaara Rozenblum <yaara.rozenblum@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Reviewed-by: NStanislaw Gruszka <sgruszka@redhat.com>
[reword commit log, use a separate lock]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

ieee80211_rx_status.flags is full. Define a new vht_flag
variable to be able to set more VHT related flags and make
room in flags.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath10k]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Teach sta_info_flush() to optionally also remove stations
from all VLANs associated with an AP interface to optimise
the station removal (in particular, synchronize_net().)

To not have to add the vlans argument throughout, do some
refactoring.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no reason to have one synchronize_net() for each
removed station, refactor the code slightly to have just
a single synchronize_net() for all stations.

Note that this is currently useless as hostapd removes
stations one by one and this coalescing never happens.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If we can assume that stations are never referenced by the
driver after sta_state returns (and this is true since the
previous iwlmvm patch and for all other drivers) then we
don't need to delay station destruction, and don't need to
play tricks with rcu_barrier() etc.

This should speed up some scenarios like hostapd shutdown.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Measure TX latency and jitter statistics per station per TID.
These Measurements are disabled by default and can be enabled
via debugfs.

Features included for each station's TID:

1. Keep count of the maximum and average latency of Tx frames.
2. Keep track of many frames arrived in a specific time range
   (need to enable through debugfs and configure the bins ranges)
Signed-off-by: NMatti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Use put_unaligned_le16 in mesh_plink_frame_tx.
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This adds generic cipher scheme support to mac80211, such schemes
are fully under control by the driver. On hw registration drivers
may specify additional HW ciphers with a scheme how these ciphers
have to be handled by mac80211 TX/RR. A cipher scheme specifies a
cipher suite value, a size of the security header to be added to
or stripped from frames and how the PN is to be verified on RX.
Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>