In case of Dynamic SMPS enable RTS/CTS for all rates.
Signed-off-by: NChaitanya T K <chaitanya.mgit@gmail.com>
[change comment]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch does the following:
- Remove unnecessary flags field used by PERR element
- Use the per target flags defined in <linux/ieee80211.h>
- Process the target only subfield based on case E2 of
  IEEE802.11-2012 13.10.9.3
Signed-off-by: NChun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The IEEE802.11-2012 specification is vague regarding SMPS operation during
TDLS. It does not define a clear way to transition between SMPS states.

To avoid interop issues, set SMPS to off when TDLS peers are connected.
Accomplish this by extending the definition of the AUTOMATIC state. If the
driver forces a state other than OFF, disconnect all TDLS peers.

While at it, avoid changing the SMPS state of the peer STA. We have no
way to control it, so try and behave correctly towards it.

Move the TDLS peer-teardown function to where the rest of the TDLS code
resides.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We already set a station to be associated when peering completes, both
in user space and in the kernel.  Thus we should always have an
associated sta before sending data frames to that station.

Failure to check assoc state can cause crashes in the lower-level driver
due to transmitting unicast data frames before driver sta structures
(e.g. ampdu state in ath9k) are initialized.  This occurred when
forwarding in the presence of fixed mesh paths: frames were transmitted
to stations with whom we hadn't yet completed peering.

Cc: stable@vger.kernel.org
Reported-by: NAlexis Green <agreen@cococorp.com>
Tested-by: NJesse Jones <jjones@cococorp.com>
Signed-off-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When processing a PREQ or PREP it's critical to use the incoming SN. If
that is improperly done routing loops and other types of badness can
happen. But the code was always processing path messages for deactivated
paths. This path fixes that so that if we have a valid SN then we use it
to verify that it is a message we can accept. For reference the relevant
section of the standard is 13.10.8.4 which doesn't address the deactivated
path case at all.

I also included a special case for when our peer reboots or restarts
networking. This is an important case because without it there can be a
very long delay before we accept path messages from that peer. It's also a
simple case and intimately associated with processing messages for
deactivated paths so I used one patch instead of two.
Signed-off-by: NAlexis Green <agreen@cococorp.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The 2012 spec mentions that path SNs can be invalid when created (see
section 13.10.8.4 table 13-9) but AFAICT never talks about invalidating
SNs. Which makes sense: if we have figured out the path to a target at a
certain SN then we want to remember that fact. Failing to do so can lead
to routing loops because if we don't have a valid SN then we have no way
of knowing whether an incoming path message leads to or away from the
target.

However currently when discovery fails we zero out mpath->flags which
clears MESH_PATH_SN_VALID. This patch fixes that so that only the
discovery relevant flags are cleared.
Signed-off-by: NAlexis Green <agreen@cococorp.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When the nexthop is unable to resolve its own nexthop it will send back a
PERR with a zero target_sn. According to section 13.10.11.4.3 step b in the
2012 standard that perr should be forwarded and the associated mpath->sn
should be incremented. Neither one of those was happening which is rather
bad because the originator was not told that packets are black holing.
Signed-off-by: NAlexis Green <agreen@cococorp.com>
CC: Jesse Jones <jjones@cococorp.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Define a station chandef, to be used for wider-bw TDLS peers. When both
peers support the feature, upgrade the channel bandwidth to the maximum
allowed by both peers and regulatory. Currently widths up to 80MHz are
supported in the 5GHz band.

When a TDLS peer connects/disconnects recalculate the channel type of the
current chanctx.
Make the chanctx width calculation consider wider-bw TDLS peers and
similarly fix the max_required_bw calculation for the chanctx min_def.
Since the sta->bandwidth is calculated only later on, take
bss_conf.chandef.width as the minimal width for station interface.

Set the upgraded channel width in the VHT-operation set during TDLS setup.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Allow a device to specify support for the TDLS wider-bandwidth feature.
Indicate this support during TDLS setup in the ext-capab IE and set an
appropriate station flag when our TDLS peer supports it.
This feature gives TDLS peers the ability to use a wider channel than
the base width of the BSS. For instance VHT capable TDLS peers connected
on a 20MHz channel can extend the channel to 80MHz, if regulatory
considerations allow it.

Do not cap the bandwidth of such stations by the current BSS channel width
in mac80211.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If reconfiguration fails, local->in_reconfig is never
cleaned, resulting in rx frames being dropped next
time the device is started.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Simply return NULL in this case, instead of crashing. This can
simplify callers that would otherwise have to check for this
explicitly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The beacon struct is already available in many contexts that
are also already in an RCU read-locked section. Avoid that by
using the existing beacon struct pointer directly.
Signed-off-by: NWojciech Dubowik <Wojciech.Dubowik@neratec.com>
[rewrite subject/add commit message]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The code was always a bit awkward due to the 80-col restriction
and got worse in the previous patch. Refactor it a bit into its
own function to make it read nicer.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are now a fairly large number of mesh fields that really
aren't needed in any other modes; move those into their own
structure and allocate them separately.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's a long-standing TODO item to use this flag in the cooked
monitor RX, but clearly it was never needed and now this hasn't
been used by userspace for a long time, so no userspace changes
could require it now.

Remove the unused flag.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Currently, the station hash table lookup (or iteration) must
access two cachelines for each station - the one with the hash
table node, and the one with the MAC address.

Duplicate the MAC address next to the hash node to get rid of
this. Since the MAC address is static there's no consistency
problem introduced by this.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When there are multiple RX queues, the PN checks in mac80211 cannot be
used since packets might be processed out of order on different CPUs.

Allow the driver to report that the PN has been checked, drivers that
will use multi-queue RX will have to set this flag.

For now, the flag is only valid when the frame has been decrypted, in
theory that restriction doesn't have to be there, but in practice the
hardware will have decrypted the frame already.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This counter is inherently racy (since it can be incremented by RX
as well as by concurrent TX) and only available in debugfs. Instead
of fixing it to be per-CPU or similar, remove it for now. If needed
it should be added without races and with proper nl80211, perhaps
even addressing the threshold reporting TODO item that's been there
since the code was originally added.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

As there's no driver using this capability and reporting zero-length
A-MPDU subframes for radiotap monitoring, remove the capability to
free up two RX flags.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When introducing multiple RX queues, a single NAPI struct will not
be sufficient. Instead of trying to store multiple, simply change
the API to have the NAPI struct passed to the RX function. This of
course means that drivers using rx_irqsafe() cannot use NAPI, but
that seems a reasonable trade-off, particularly since only two of
all drivers are currently using it at all.

While at it, we can now remove the IEEE80211_RX_REORDER_TIMER flag
again since this code path cannot have a napi struct anyway.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are no RX queues in mac80211 (yet), the comment should refer
to the TID (including one slot for non-QoS) rather than 'RX queue'.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This function is only used in the RX code, so moving it into
that file gives the compiler better optimisation possibilities
and also allows us to remove the check for short frames (which
in the RX path cannot happen, but as a generic utility needed
to be checked.)
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Short frames less than 16 octets are already blocked in the monitor
code by the should_drop_frame() function, and cannot get into the
regular RX path. Therefore, this check can never trigger and the
counter invariably stays zero. Remove the useless code.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This struct member is only assigned, never used otherwise;
remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

We typically use 'sta' for the station info struct, and if needed
'pubsta' for the public (driver-visible) portion thereof. Do this
in the ieee80211_sta_ps_transition() function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no driver using this, so remove it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Commit 514ac99c "can: fix multiple delivery of a single CAN frame for
overlapping CAN filters" requires the skb->tstamp to be set to check for
identical CAN skbs.

Without timestamping to be required by user space applications this timestamp
was not generated which lead to commit 36c01245 "can: fix loss of CAN frames
in raw_rcv" - which forces the timestamp to be set in all CAN related skbuffs
by introducing several __net_timestamp() calls.

This forces e.g. out of tree drivers which are not using alloc_can{,fd}_skb()
to add __net_timestamp() after skbuff creation to prevent the frame loss fixed
in mainline Linux.

This patch removes the timestamp dependency and uses an atomic counter to
create an unique identifier together with the skbuff pointer.

Btw: the new skbcnt element introduced in struct can_skb_priv has to be
initialized with zero in out-of-tree drivers which are not using
alloc_can{,fd}_skb() too.
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

cd->sw_addr is used as a MDIO bus address, which cannot exceed
PHY_MAX_ADDR (32), our check was off-by-one.

Fixes: 5e95329b ("dsa: add device tree bindings to register DSA switches")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

port_index is used an index into an array, and this information comes
from Device Tree, make sure that port_index is not equal to the array
size before using it. Move the check against port_index earlier in the
loop.

Fixes: 5e95329b: ("dsa: add device tree bindings to register DSA switches")
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to abort attribute setting or object addition, if the
prepare phase returned operation not supported.

Thus, abort these two transactions only if the error is not -EOPNOTSUPP.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NScott Feldman <sfeldma@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reconsidering my commit 20462155 "net: inet_diag: export IPV6_V6ONLY
sockopt", I am not happy with the limitations it causes for socket
analysing code in userspace. Exporting the value only if it is set makes
it hard for userspace to decide whether the option is not set or the
kernel does not support exporting the option at all.

>From an auditor's perspective, the interesting question for listening
AF_INET6 sockets is: "Does it NOT have IPV6_V6ONLY set?" Because it is
the unexpected case. This patch allows to answer this question reliably.
Signed-off-by: NPhil Sutter <phil@nwl.cc>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Until now when a querier was present static entries couldn't be deleted.
Fix this and allow the user to manipulate the mdb with or without a
querier.
Signed-off-by: NSatish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Incoming packet should be either in backlog queue or
in RCU read-side section. Otherwise, the final sequence of
flush_backlog() and synchronize_net() may miss packets
that can run without device reference:

CPU 1                  CPU 2
                       skb->dev: no reference
                       process_backlog:__skb_dequeue
                       process_backlog:local_irq_enable

on_each_cpu for
flush_backlog =>       IPI(hardirq): flush_backlog
                       - packet not found in backlog

                       CPU delayed ...
synchronize_net
- no ongoing RCU
read-side sections

netdev_run_todo,
rcu_barrier: no
ongoing callbacks
                       __netif_receive_skb_core:rcu_read_lock
                       - too late
free dev
                       process packet for freed dev

Fixes: 6e583ce5 ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit 381c759d ("ipv4: Avoid crashing in ip_error")
fixes a problem where processed packet comes from device
with destroyed inetdev (dev->ip_ptr). This is not expected
because inetdev_destroy is called in NETDEV_UNREGISTER
phase and packets should not be processed after
dev_close_many() and synchronize_net(). Above fix is still
required because inetdev_destroy can be called for other
reasons. But it shows the real problem: backlog can keep
packets for long time and they do not hold reference to
device. Such packets are then delivered to upper levels
at the same time when device is unregistered.
Calling flush_backlog after NETDEV_UNREGISTER_FINAL still
accounts all packets from backlog but before that some packets
continue to be delivered to upper levels long after the
synchronize_net call which is supposed to wait the last
ones. Also, as Eric pointed out, processed packets, mostly
from other devices, can continue to add new packets to backlog.

Fix the problem by moving flush_backlog early, after the
device driver is stopped and before the synchronize_net() call.
Then use netif_running check to make sure we do not add more
packets to backlog. We have to do it in enqueue_to_backlog
context when the local IRQ is disabled. As result, after the
flush_backlog and synchronize_net sequence all packets
should be accounted.

Thanks to Eric W. Biederman for the test script and his
valuable feedback!
Reported-by: NVittorio Gambaletta <linuxbugs@vittgam.net>
Fixes: 6e583ce5 ("net: eliminate refcounting in backlog queue")
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NJulian Anastasov <ja@ssi.bg>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit c29390c6 ("xps: must clear sender_cpu before forwarding")
fixed an issue in normal forward path, caused by sender_cpu & napi_id
skb fields being an union.

Bridge is another point where skb can be forwarded, so we need
the same cure.

Bug triggers if packet was received on a NIC using skb_mark_napi_id()

Fixes: 2bd82484 ("xps: fix xps for stacked devices")
Signed-off-by: NEric Dumazet <edumazet@google.com>
Reported-by: NBob Liu <bob.liu@oracle.com>
Tested-by: NBob Liu <bob.liu@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pktgen_thread_worker() doesn't need to wait for kthread_stop(), it
can simply exit. Just pktgen_create_thread() and pg_net_exit() should
do get_task_struct()/put_task_struct(). kthread_stop(dead_thread) is
fine.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

pktgen_thread_worker() is obviously racy, kthread_stop() can come
between the kthread_should_stop() check and set_current_state().
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Reported-by: NJan Stancek <jstancek@redhat.com>
Reported-by: NMarcelo Leitner <mleitner@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

addr_is_blank() should return true if family is neither AF_INET nor
AF_INET6.  This is what its counterpart entity_addr_t::is_blank_ip() is
doing and it is the right thing to do: in process_banner() we check if
our address is blank and if it is "learn" it from our peer.  As it is,
we never learn our address and always send out a blank one.  This goes
way back to ceph.git commit dd732cbfc1c9 ("use sockaddr_storage; and
some ipv6 support groundwork") from 2009.

While at at, do not open-code ipv6_addr_any() and use INADDR_ANY
constant instead of 0.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Reviewed-by: NSage Weil <sage@redhat.com>

Grab a reference on a network namespace of the 'rbd map' (in case of
rbd) or 'mount' (in case of ceph) process and use that to open sockets
instead of always using init_net and bailing if network namespace is
anything but init_net.  Be careful to not share struct ceph_client
instances between different namespaces and don't add any code in the
!CONFIG_NET_NS case.

This is based on a patch from Hong Zhiguo <zhiguohong@tencent.com>.
Signed-off-by: NIlya Dryomov <idryomov@gmail.com>
Reviewed-by: NSage Weil <sage@redhat.com>

This kernel patch exports the value of the new
ignore_routes_with_linkdown via netconf.

v2: changes to notify userspace via netlink when sysctl values change
and proposed for 'net' since this could be considered a bugfix
Signed-off-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Suggested-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Acked-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>