omap3430 TRM says the OTG address space is 4k, not 8k.

Cc: linux-usb@vger.kernel.org
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch removes #ifdef around usb_nop_xceiv_register()
from board-omap3evm.c
Signed-off-by: NMaulik Mankad <x0082077@ti.com>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NFelipe Balbi <felipe.balbi@nokia.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch updates the omap3_evm_defconfig to
select these options:
  * CONFIG_PM_DEBUG
  * CONFIG_DEBUG_FS
  * CONFIG_OMAP_SMARTREFLEX
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds a default config for the Timll Devkit8000.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

These patches add board support for the Timll DevKit8000.

The DevKit8000 is a beagle board clone from Timll, sold by
armkits.com. The DevKit8000 has RS232 serial port, LCD, DVI-D,
S-Video, Ethernet, SD/MMC, keyboard, camera, SPI, I2C, USB and
JTAG interface.
Signed-off-by: NThomas Weber <weber@corscience.de>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform hook-up interface to support I2C based GPIo expander
(TCA6416).

There are 3 instances of I2C Expander on AM3517EVM,
	- One is over I2C-2 mounted on Base board
	- Two are over I2C3 mounted on UI Card
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform hook-up interface to support RTC driver (S35390A).
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add basic I2C board Hook-up support, where all the 3 I2C instances
are getting registered.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

If not configured it will be exported as normal GPIO led.
Signed-off-by: NJonas Zetterberg <jozz@jozz.se>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enabled VMMC2 LDO voltage regulator on TWL4030.
Added GPIO's (power down and reset) for WIFI chip.
Signed-off-by: NAnders Hedlund <anders.j.hedlund@gmail.com>
Signed-off-by: NJonas Zetterberg <jozz@jozz.se>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add timing data for the Numonyx M65KxxxxAM SDRAM chip, used on the
IGEP v2 board.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds support for flashes on IGEP v2 boards. For now
only OneNAND is supported.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform init code for EHCI driver on IGEP v2
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Fix typo on IGEP v2 board
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform data for the twl4030_codec MFD on IGEP v2
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Enable DSS2 and update defconfig for current kernel.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Update pandora's regulator setup:
- add new regulators: VAUX2, VAUX4 and VSIM
- add new consumers: ads7846, nub controllers, USB PHY, audio DAC
- use dev names instead of struct device pointers
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch adds configuration data for DSS2 and sets up
display related regulators.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

GPIO175 is used for PEN_IRQ on the EVM. This patch
sets the mux settings for the same.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The keypad was not working properly after migrating
to matrix_keypad.

Swapped the row, col fields of the KEY() macro in
the keymap definition to get it working again.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This patch sets SYS_NIRQ for keypad input. It also
sets the same as a wakeup event from OFF mode.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Zoom3 board has omap3630 EHCI port2 connected to a ULPI phy.
GPIO_64 is connected to the PHY reset pin.
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The check for a valid mux name should be performed regardless of whether
DEBUG_FS is enabled or not. Otherwise without DEBUG_FS, we get:

Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1]
last sysfs file:
Modules linked in:
CPU: 0    Not tainted  (2.6.33-rc8 #10)
PC is at strcmp+0x18/0x40
LR is at omap_mux_init_signal+0x68/0x14c
...

This fixes the issue currently seen with boards not booting up
if DEBUG_FS is not enabled in defconfig.

Note that the earlier ifndef + ifdef now becomes simpler ifdef else:
If CONFIG_OMAP_MUX is selected, we use pin names. If it's not selected,
we only want the GPIO to mux register mapping.
Signed-off-by: NRanjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform device for McPDM interface in OMAP4 and register
its memory and irq resources.
Signed-off-by: NJorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Define McPDM physical and L3 base address for OMAP4
Signed-off-by: NJorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Support for McPDM IRQs in OMAP4
Signed-off-by: NJorge Eduardo Candelaria <x0107209@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

sdp4430_uart_config isn't used anywhere, so remove it.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

AM3517/05 has few additional control module registers to control
the new IP's, like VPFE, USBOTG, CPGMAC.

This patch adds the bit defination for INTR_CLR and SW_RST control
register.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add base address definations for new AM35xx IPSS modules, like
VPFE, USBOTG, CPGMAC.

Please note that the OMAP34xx IVA2 memory space is being used for
AM35xx IPSS modules.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Changes for setting the padconf value for sys_nirq line which is
connected to T2 INTR1. This will fix the T2 keypad wakeup.
Signed-off-by: NLesly A M <x0080970@ti.com>
Signed-off-by: NTeerth Reddy <teerth@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Get rid of the ifdeffery in omap_mux_init by creating
omap_mux_init_package and omap_mux_init_signals functions.
Signed-off-by: NTony Lindgren <tony@atomide.com>

EMMC can have two voltage supplies, Vcc and VccQ
which are implemented in the code as consumer
supplies vmmc and vmmc_aux.

If the regulator that supplies vmmc_aux is shared
with other consumers, then sending it to sleep
will disrupt those consumers.  However, the
TWL4030-family regulators may have OFF remapped
to SLEEP, in which case 'regulator_disable()'
will put the regulator to sleep only when all
consumers are disabled - which is the desired
behaviour.

This patch adds a platform data field to allow
that option.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

An eMMC may be always powered on, so that the lowest
power saving state possible is sleeping. Add a field
to the platform data to indicate that.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

It has been discovered that, when eMMC is powered off, current
will flow from OMAP eMMC data pull-ups to the eMMC voltage supply.
Configuring pads for OMAP off-mode does not help because eMMC is
powered off independently of OMAP off-mode.  Hence the pads are
now re-configured when eMMC is powered on or off.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Call the PM context-loss count function, now that there
is a prototype for it.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

hsmmc.[ch] no longer has any dependency on twl4030
and variable names should be renamed to reflect that.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>