- 18 1月, 2011 1 次提交
-
-
由 Rajkumar Manoharan 提交于
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 1月, 2011 1 次提交
-
-
由 Sujith Manoharan 提交于
The chainmask value along with other configuration has to be set on the target for packet injection. Fix this and also move the monitor interface addition before the channel set segment to ensure that the opmode is updated properly. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 05 1月, 2011 3 次提交
-
-
由 Sujith Manoharan 提交于
And add the copyright/license header. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
When returning to the operating channel, a full HW reset has to be done instead of a fast channel change. Since sw_scan_complete() is called after the config() call for the home channel, we end up doing a FCC. Fix this issue by checking the OFFCHANNEL flag to determine FCC. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
The device has to be reset when a FATAL event is received. Not doing so would leave the card in a non-working state. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 12月, 2010 1 次提交
-
-
由 Sujith Manoharan 提交于
The commit "ath9k_hw: warn if we cannot change the power to the chip" introduced a new warning to indicate chip powerup failures, but this is not required for devices that have been removed. Handle USB device removal properly by checking for unplugged status. For PCI devices, this warning will still be seen when the card is pulled out, not sure how to check for card removal. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 09 12月, 2010 1 次提交
-
-
由 Sujith Manoharan 提交于
The HW has to be set to FULLSLEEP mode during suspend, when no interface has been brought up. Not doing this would break resume, as the chip won't be powered up at all. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 25 11月, 2010 1 次提交
-
-
由 Rajkumar Manoharan 提交于
Categorize AR7010 & AR9287 devices based on driver_info of usb_device_id, instead of PIDs. This avoids per-device cases and minimize code changes for new device addition. Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 17 11月, 2010 1 次提交
-
-
由 Mohammed Shafi Shajakhan 提交于
The calibration data variable size is based on the number of channels available in the ath9k driver. Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 25 8月, 2010 1 次提交
-
-
由 Vivek Natarajan 提交于
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 05 8月, 2010 1 次提交
-
-
由 Felix Fietkau 提交于
The noise floor history buffer is currently not kept per channel, which can lead to problems when changing channels from a clean channel to a noisy one. Also when switching from HT20 to HT40, the noise floor history buffer is full of measurements, but none of them contain data for the extension channel, which it needs quite a bit of time to recover from. This patch puts all the per-channel calibration data into a single data structure, and gives the the driver control over whether that is used per-channel or even not used for some channels. For ath9k_htc, I decided to keep this per-channel in order to avoid creating regressions. For ath9k, the data is kept only for the operating channel, which saves some space. ath9k_hw takes care of wiping old data when the operating channel or its channel flags change. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 01 7月, 2010 1 次提交
-
-
由 Sujith 提交于
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 16 6月, 2010 1 次提交
-
-
由 Sujith 提交于
Now that ampdu_action() can sleep, remove all the driver hacks and just issue WMI commands to the target. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 15 6月, 2010 1 次提交
-
-
由 Felix Fietkau 提交于
Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 04 6月, 2010 1 次提交
-
-
由 Sujith 提交于
This patch fixes beacon distribution in IBSS mode by configuring the hardware beacon queue properly. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 03 6月, 2010 4 次提交
-
-
由 John W. Linville 提交于
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
This patch removes a large chunk of code dealing with rate management within the driver and simplifying things by removing the hacky method of calculating HT changes. A subsequent patch would fix this by just using BSS_CHANGED_HT from mac80211. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
This patch initializes the beacon and CAB HW queues when the driver is loaded. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 25 5月, 2010 1 次提交
-
-
由 Tejun Heo 提交于
Implicit slab.h inclusion via percpu.h is about to go away. Make sure gfp.h or slab.h is included as necessary. Signed-off-by: NTejun Heo <tj@kernel.org> Cc: Stephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 08 5月, 2010 1 次提交
-
-
由 Sujith 提交于
The current way of managing beaconing in ad-hoc mode has a subtle race - the beacon obtained from mac80211 is freed in the SWBA handler rather than the TX completion routine. But transmission of beacons goes through the normal SKB queue maintained in hif_usb, leading to a situation where __skb_dequeue() in the TX completion handler goes kaput. Fix this by simply getting a beacon from mac80211 for every SWBA and free it in its completion routine. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 28 4月, 2010 1 次提交
-
-
由 Vivek Natarajan 提交于
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 27 4月, 2010 1 次提交
-
-
由 Sujith 提交于
When the USB device has been unplugged, there is no point in trying to send commands to the target. Fix this by denying all WMI commands in such a case. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 17 4月, 2010 2 次提交
-
-
由 Sujith 提交于
This patch fixes a bunch of endian issues that were exposed by sparse. It's a miracle that the driver worked at all till now. The Lord be praised. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 08 4月, 2010 2 次提交
-
-
由 Vivek Natarajan 提交于
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Vivek Natarajan 提交于
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 01 4月, 2010 2 次提交
-
-
由 Sujith 提交于
Stop/restart TX queues when the internal SKB queue is full. This helps handle TX better under heavy load. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
The calculation of RX filter is fairly different between ath9k and ath9k_htc, trying to make this common between the two drivers would result in code churn. While at it, remove the handling of PSPOLL filter, it can be added when(if) AP support is added to ath9k_htc. Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 24 3月, 2010 2 次提交
-
-
由 Sujith 提交于
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith 提交于
Features: * Station mode * IBSS mode * Monitor mode * Legacy support * HT support * TX/RX 11n Aggregation * HW encryption * LED * Suspend/Resume For more information: http://wireless.kernel.org/en/users/Drivers/ath9k_htcSigned-off-by: NSujith <Sujith.Manoharan@atheros.com> Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-