- 19 1月, 2011 1 次提交
-
-
由 Bob Copeland 提交于
ath5k_reset must be called with sc->lock. Since the tx queue watchdog runs in a workqueue and accesses sc, it's appropriate to just take the lock over the whole function. Signed-off-by: NBob Copeland <me@bobcopeland.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 18 1月, 2011 3 次提交
-
-
由 Rajkumar Manoharan 提交于
The power detector adc offset calibration has to be done on 4 minutes interval (longcal * pa_skip_count). But the commit "ath9k_hw: fix a noise floor calibration related race condition" makes the PA calibration executed more frequently beased on nfcal_pending value. Running PAOffset calibration lesser than longcal interval doesn't help anything and the worse part is that it causes NF load timeouts and RX deaf conditions. In a very noisy environment, where the distance b/w AP & station is ~10 meter and running a downlink udp traffic with frequent background scan causes "Timeout while waiting for nf to load: AR_PHY_AGC_CONTROL=0x40d1a" and moves the chip into deaf state. This issue was originaly reported in Android platform where the network-manager application does bgscan more frequently on AR9271 chips. (AR9285 family usb device). Cc: stable@kernel.org Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Luis R. Rodriguez 提交于
There is an interoperability with AR9382/AR9380 in L1 state with a few root complexes which can cause a hang. This is fixed by setting some work around bits on the PCIE PHY. We fix by using a new ini array to modify these bits when the radio is idle. Cc: stable@kernel.org Cc: Jack Lee <jack.lee@atheros.com> Cc: Carl Huang <carl.huang@atheros.com> Cc: David Quan <david.quan@atheros.com> Cc: Nael Atallah <nael.atallah@atheros.com> Cc: Sarvesh Shrivastava <sarvesh.shrivastava@atheros.com> Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 11 1月, 2011 5 次提交
-
-
由 Sujith Manoharan 提交于
The chainmask value along with other configuration has to be set on the target for packet injection. Fix this and also move the monitor interface addition before the channel set segment to ensure that the opmode is updated properly. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Commit "ath9k_hw: Abort rx if hw is not coming out of full sleep in reset" uncondionally added aborting RX DMA in a HW reset, though it is a bit unclear as to why this is needed. Anyway, RX DMA is handled in the target for USB devices, and this would interfere with normal operations (scanning etc.), so fix this. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
Hardcode the output voltage of x-PA bias LDO to the lowest value for UB94. The card doesn't get too hot now. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
AR9287 based devices have issues with ADC gain calibration which would cause uplink throughput drops in HT40 mode. Remove ADC gain from the supported calibration algorithms. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
USB devices do not require the chip test routine. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 06 1月, 2011 3 次提交
-
-
由 John W. Linville 提交于
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 John W. Linville 提交于
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 05 1月, 2011 19 次提交
-
-
由 Sujith Manoharan 提交于
To inject a packet in monitor mode, a dummy station has to be associated with the monitor interface in the target. Failing to do this would result in a firmware crash on the device. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
ath5k_eeprom_mode_from_channel() returns -1 on error but we're storing the result in "ee_mode" which is an unsigned char. This breaks the error handling. This patch makes "ee_mode" an int. Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohammed Shafi Shajakhan 提交于
Remove some obvious looking dead code and rename few functions Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Rajkumar Manoharan 提交于
Restart the beacon timers only if the beacon was already configured. Otherwise beacons timers are restarted unnecessarily in unassociated state too. Cc: stable@kernel.org Signed-off-by: NRajkumar Manoharan <rmanoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohammed Shafi Shajakhan 提交于
This reverts commit 0ce3bcfc. Event though with the above commit we obtain the configured DTIM period from the AP rather than always hardcoding it to '1', this seems to cause problems under the following scenarios: * Preventing association with broken AP's * Adds latency in roaming So its better to always use the safe value of '1' for dtim period Cc: Jouni Malinen <Jouni.Malinen@Atheros.com> Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Felix Fietkau 提交于
An Rx DMA descriptor can have multiple error bits set, and some error bits (e.g. MIC failure) are filtered by the driver based on other criteria. Remove the 'else' in various error bit checks so that all error information is properly passed to the driver. Signed-off-by: NFelix Fietkau <nbd@openwrt.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
And add the copyright/license header. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
When returning to the operating channel, a full HW reset has to be done instead of a fast channel change. Since sw_scan_complete() is called after the config() call for the home channel, we end up doing a FCC. Fix this issue by checking the OFFCHANNEL flag to determine FCC. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
The device has to be reset when a FATAL event is received. Not doing so would leave the card in a non-working state. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
There is no need to lock the various work cancellation calls. This will be helpful when handling FATAL events. Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Sujith Manoharan 提交于
When doing a channel change, the pending URBs have to be killed properly on calling htc_stop(). This fixes the probe response timeout seen when sending UDP traffic at a high rate and running background scan at the same time. Cc: stable <stable@kernel.org> Signed-off-by: NSujith Manoharan <Sujith.Manoharan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohammed Shafi Shajakhan 提交于
Some minor clean ups in assigning values to beacon config parameters Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch revamps some common code-paths which are shared between (re-)initialization and suspend/resume subroutines. It also adds some helpful comments about quirks and associated difficulties. It's quite big, but it should fix #25382: <https://bugzilla.kernel.org/show_bug.cgi?id=25382> And hopefully the code is robust enough to deal with all possible suspend/resume scenarios without requiring the user to do any sort of manual and possibly dangerous work. Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
By removing two "safety" msleeps (and an echo nop), the channel change delay is effectively halved. Previously, the delay could be as long as 260 ms and the device could not go off-channel without risking to miss the next DTIM beacon [interval ~307 ms]. Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Christian Lamparter 提交于
This patch adds a forgotten bail-out path. Signed-off-by: NChristian Lamparter <chunkeey@googlemail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bob Copeland 提交于
ath5k_reset is called from process context and takes the cc_lock with plain spin_lock(), but cc_lock can also be taken from tasklets in softirq context. Thus we need to at least use spin_lock_bh. This fixes the following lockdep warning: [ 19.967874] sky2 0000:01:00.0: eth0: enabling interface [ 19.982761] ieee80211 phy0: device now idle [ 20.904809] NET: Registered protocol family 17 [ 21.243857] ieee80211 phy0: device no longer idle - scanning [ 21.404343] [ 21.404346] ================================= [ 21.404450] [ INFO: inconsistent lock state ] [ 21.404518] 2.6.37-rc7-wl+ #242 [ 21.404582] --------------------------------- [ 21.404650] inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage. [ 21.404721] kworker/u:4/982 [HC0[0]:SC1[3]:HE1:SE0] takes: [ 21.404792] (&(&common->cc_lock)->rlock){+.?...}, at: [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] {SOFTIRQ-ON-W} state was registered at: [ 21.405011] [<c105cadd>] __lock_acquire+0x62f/0x13c1 [ 21.405011] [<c105d944>] lock_acquire+0xd5/0xf1 [ 21.405011] [<c12c978d>] _raw_spin_lock+0x45/0x72 [ 21.405011] [<f8111533>] ath5k_reset+0x2c0/0x349 [ath5k] [ 21.405011] [<f8111a7a>] ath5k_start+0xb8/0x139 [ath5k] [ 21.405011] [<f849c714>] ieee80211_do_open+0x13f/0x819 [mac80211] [ 21.405011] [<f849ce51>] ieee80211_open+0x63/0x66 [mac80211] [ 21.405011] [<c1258b2e>] __dev_open+0x8d/0xb6 [ 21.405011] [<c1255c64>] __dev_change_flags+0x9d/0x114 [ 21.405011] [<c1258a75>] dev_change_flags+0x18/0x44 [ 21.405011] [<c1262990>] do_setlink+0x23f/0x521 [ 21.405011] [<c1262d58>] rtnl_setlink+0xe6/0xea [ 21.405011] [<c126347c>] rtnetlink_rcv_msg+0x18a/0x1a0 [ 21.405011] [<c126d5f0>] netlink_rcv_skb+0x35/0x7b [ 21.405011] [<c12632eb>] rtnetlink_rcv+0x20/0x27 [ 21.405011] [<c126d370>] netlink_unicast+0x1bb/0x21e [ 21.405011] [<c126db21>] netlink_sendmsg+0x23b/0x288 [ 21.405011] [<c124823c>] sock_sendmsg+0xac/0xc4 [ 21.405011] [<c1248680>] sys_sendmsg+0x152/0x1a2 [ 21.405011] [<c1249b0d>] sys_socketcall+0x214/0x275 [ 21.405011] [<c10029d0>] sysenter_do_call+0x12/0x36 [ 21.405011] irq event stamp: 138032 [ 21.405011] hardirqs last enabled at (138032): [<c12ca252>] _raw_spin_unlock_irqrestore+0x3b/0x5e [ 21.405011] hardirqs last disabled at (138031): [<c12c98cc>] _raw_spin_lock_irqsave+0x18/0x7e [ 21.405011] softirqs last enabled at (138024): [<f84a570e>] ieee80211_tx_skb+0x47/0x49 [mac80211] [ 21.405011] softirqs last disabled at (138027): [<c100452b>] do_softirq+0x63/0xb4 [ 21.405011] [ 21.405011] other info that might help us debug this: [ 21.405011] 3 locks held by kworker/u:4/982: [ 21.405011] #0: (name){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b [ 21.405011] #1: ((&(&local->scan_work)->work)){+.+.+.}, at: [<c1046158>] process_one_work+0x1b8/0x41b [ 21.405011] #2: (&local->mtx){+.+.+.}, at: [<f84920fb>] ieee80211_scan_work+0x32/0x4a4 [mac80211] [ 21.405011] [ 21.405011] stack backtrace: [ 21.405011] Pid: 982, comm: kworker/u:4 Not tainted 2.6.37-rc7-wl+ #242 [ 21.405011] Call Trace: [ 21.405011] [<c12c6e68>] ? printk+0x1d/0x25 [ 21.405011] [<c105a742>] print_usage_bug+0x181/0x18b [ 21.405011] [<c105b196>] ? check_usage_forwards+0x0/0xb6 [ 21.405011] [<c105a9ec>] mark_lock+0x2a0/0x4aa [ 21.405011] [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd [ 21.405011] [<c105ca68>] __lock_acquire+0x5ba/0x13c1 [ 21.405011] [<c1059eed>] ? trace_hardirqs_off_caller+0x18/0x8d [ 21.405011] [<c1059f6d>] ? trace_hardirqs_off+0xb/0xd [ 21.405011] [<c1050411>] ? local_clock+0x2c/0x4f [ 21.405011] [<c1059e00>] ? save_trace+0x2/0xa0 [ 21.405011] [<c105ac39>] ? mark_held_locks+0x43/0x5b [ 21.405011] [<c12ca252>] ? _raw_spin_unlock_irqrestore+0x3b/0x5e [ 21.405011] [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<c105d944>] lock_acquire+0xd5/0xf1 [ 21.405011] [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<c12c9b1a>] _raw_spin_lock_bh+0x4a/0x77 [ 21.405011] [<f8115780>] ? ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<f8115780>] ath5k_ani_calibration+0x29/0x5d9 [ath5k] [ 21.405011] [<c105ac39>] ? mark_held_locks+0x43/0x5b [ 21.405011] [<f8113496>] ath5k_tasklet_ani+0x1d/0x27 [ath5k] [ 21.405011] [<c1037304>] tasklet_action+0x96/0x137 [ 21.405011] [<c10379b5>] __do_softirq+0xde/0x1c3 [ 21.405011] [<c10b0cef>] ? arch_get_unmapped_area_topdown+0x3b/0x127 [ 21.405011] [<c10378d7>] ? __do_softirq+0x0/0x1c3 [ 21.405011] <IRQ> [<c1036dee>] ? irq_exit+0x3d/0x49 [ 21.405011] [<c1003b4f>] ? do_IRQ+0x98/0xac [ 21.405011] [<c1002eee>] ? common_interrupt+0x2e/0x34 [ 21.405011] [<c103007b>] ? sys_unshare+0x57/0x226 [ 21.405011] [<c1047fee>] ? queue_delayed_work+0x1/0x27 [ 21.405011] [<f84a83a0>] ? ieee80211_queue_delayed_work+0x2e/0x33 [mac80211] [ 21.405011] [<f8492528>] ? ieee80211_scan_work+0x45f/0x4a4 [mac80211] [ 21.405011] [<c104620e>] ? process_one_work+0x26e/0x41b [ 21.405011] [<c1046158>] ? process_one_work+0x1b8/0x41b [ 21.405011] [<f84920c9>] ? ieee80211_scan_work+0x0/0x4a4 [mac80211] [ 21.405011] [<c10466b6>] ? worker_thread+0x18a/0x2a5 [ 21.405011] [<c12ca25e>] ? _raw_spin_unlock_irqrestore+0x47/0x5e [ 21.405011] [<c104652c>] ? worker_thread+0x0/0x2a5 [ 21.405011] [<c104abe7>] ? kthread+0x67/0x6c [ 21.405011] [<c104ab80>] ? kthread+0x0/0x6c [ 21.405011] [<c1002efa>] ? kernel_thread_helper+0x6/0x10 Signed-off-by: NBob Copeland <me@bobcopeland.com> Acked-by: NBruno Randolf <br1@einfach.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Brian Prodoehl 提交于
For the AR9002, the spur frequency read from the EEPROM is mangled before being compared against AR_NO_SPUR. This results in the driver trying to set up the spur mitigation for bogus spurs, rather than cleanly breaking out. Signed-off-by: NBrian Prodoehl <bprodoehl@nomadio.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Senthil Balasubramanian 提交于
Disabling BH is not required while running from a tasklet context and so replace spin_lock_bh with just spin_lock. Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bruno Randolf 提交于
Move mac80211 functions into new file mac80211-ops.c to have a better separation and to make base.c smaller. Signed-off-by: NBruno Randolf <br1@einfach.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 12月, 2010 9 次提交
-
-
由 Mohammed Shafi Shajakhan 提交于
It looks like some hardware registers are left into undefined state after suspend/resume. At minimum, this can cause odd issues related to key cache and hardware trying to encrypt/decrypt frames unexpectedly. This seems to happen even when there is no keys configured, i.e., hardware can end up touching TX frames just based of invalid key cache context even if the driver is not asking a specific entry to be used. In addition, RX can likely be affected. This patch fixes this issue. Signed-off-by: NJouni Malinen <Jouni.Malinen@Atheros.com> Signed-off-by: NMohammed Shafi Shajakhan <mshajakhan@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
The size of the eeprom data is 1088 bytes for AR9485. But a sanity check is done against 4K which would result in a 'potential read past the end of the buffer' smatch complaint. Reported-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bruno Randolf 提交于
Introduce a helper function to get the EEPROM mode from channel and remove multiple similar switch statements. Also since it's now easy to get the EEPROM mode from the channel, use them inside the functions which need it, instead of passing a redundant ee_mode parameter. Signed-off-by: NBruno Randolf <br1@einfach.org> Acked-by: NNick Kossifidis <mickflemm@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bruno Randolf 提交于
Remove redundant defines. Signed-off-by: NBruno Randolf <br1@einfach.org> Acked-by: NNick Kossifidis <mickflemm@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bruno Randolf 提交于
Add a new variable to keep track of the currently configured tx power. Before max_pwr was re-used for keeping the maximum allowed power as well as the current configuration. Doing a min() on it allows you to lower the txpower, but how would you be able to make it higher again? This patch fixes that by adding a new variable ah_cur_pwr which is used instead of txp_max_pwr to keep the current configuration. txp_max_pwr is used to check if we are within the limits. Another problem fixed by this patch is that it avoids setting a zero txpower when things are initialized first and the current power is not yet set. Signed-off-by: NBruno Randolf <br1@einfach.org> Acked-by: NNick Kossifidis <mickflemm@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bruno Randolf 提交于
And rename functions which write the powertable to make it clearer. Signed-off-by: NBruno Randolf <br1@einfach.org> Acked-by: NNick Kossifidis <mickflemm@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Bruno Randolf 提交于
Let ath5k_hw_txpower() decide if it can re-use the powertable or if it has to be recalculated instead of passing a 'fast' flag from the outside. Signed-off-by: NBruno Randolf <br1@einfach.org> Acked-by: NNick Kossifidis <mickflemm@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Dan Carpenter 提交于
There is a missing unlock when we hit the "No beacon slot available" error condition. Signed-off-by: NDan Carpenter <error27@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Hauke Mehrtens 提交于
Use function pci_is_pcie() instead of accessing struct member directly. CC: Luis R. Rodriguez <lrodriguez@atheros.com> Signed-off-by: NHauke Mehrtens <hauke@hauke-m.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-