The AGFL fixup code executes before every block allocation/free and
rectifies the AGFL based on the current, dynamic allocation
requirements of the fs. The AGFL must hold a minimum number of
blocks to satisfy a worst case split of the free space btrees caused
by the impending allocation operation. The AGFL is also updated to
maintain the implicit requirement for a minimum number of free slots
to satisfy a worst case join of the free space btrees.

Since the AGFL caches individual blocks, AGFL reduction typically
involves multiple, single block frees. We've had reports of
transaction overrun problems during certain workloads that boil down
to AGFL reduction freeing multiple blocks and consuming more space
in the log than was reserved for the transaction.

Since the objective of freeing AGFL blocks is to ensure free AGFL
free slots are available for the upcoming allocation, one way to
address this problem is to release surplus blocks from the AGFL
immediately but defer the free of those blocks (similar to how
file-mapped blocks are unmapped from the file in one transaction and
freed via a deferred operation) until the transaction is rolled.
This turns AGFL reduction into an operation with predictable log
reservation consumption.

Add the capability to defer AGFL block frees when a deferred ops
list is available to the AGFL fixup code. Add a dfops pointer to the
transaction to carry dfops through various contexts to the allocator
context. Deferring AGFL frees is  conditional behavior based on
whether the transaction pointer is populated. The long term
objective is to reuse the transaction pointer to clean up all
unrelated callchains that pass dfops on the stack along with a
transaction and in doing so, consistently defer AGFL blocks from the
allocator.

A bit of customization is required to handle deferred completion
processing because AGFL blocks are accounted against a per-ag
reservation pool and AGFL blocks are not inserted into the extent
busy list when freed (they are inserted when used and released back
to the AGFL). Reuse the majority of the existing deferred extent
free infrastructure and customize it appropriately to handle AGFL
blocks.

Note that this patch only adds infrastructure. It does not change
behavior because no callers have been updated to pass ->t_agfl_dfops
into the allocation code.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Switch to a single interface for flushing the log to a specific LSN, which
gives consistent trace point coverage and a less confusing interface.

The was only a single user of the previous xfs_log_force_lsn function,
which now also passes a NULL log_flushed argument.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

The ->t_blk_res_used field tracks how many blocks have been used in
the current transaction. This should never exceed the block
reservation (->t_blk_res) for a particular transaction. We currently
assert this condition in the transaction block accounting code, but
otherwise take no additional action should this situation occur.

The overrun generally has no effect if space ends up being available
and the associated transaction commits. If the transaction is
duplicated, however, the current block usage is used to determine
the remaining block reservation to be transferred to the new
transaction. If usage exceeds reservation, this calculation
underflows and creates a transaction with an invalid and excessive
reservation. When the second transaction commits, the release of
unused blocks corrupts the in-core free space counters. With lazy
superblock accounting enabled, this inconsistency eventually
trickles to the on-disk superblock and corrupts the filesystem.

Replace the transaction block usage accounting assert with an
explicit overrun check. If the transaction overruns the reservation,
shutdown the filesystem immediately to prevent corruption. Add a new
assert to xfs_trans_dup() to catch any callers that might induce
this invalid state in the future.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

This is a simple rename, except that xa_ail becomes ail_head.
Signed-off-by: NMatthew Wilcox <mawilcox@microsoft.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

At each mount, emit the transaction reservation type information via
tracepoints.  This makes it easier to compare the log reservation info
calculated by the kernel and xfsprogs so that we can more easily diagnose
minimum log size failures on freshly formatted filesystems.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>

Split xfs_trans_roll into a low-level helper that just rolls the
actual transaction and a new higher level xfs_trans_roll_inode
that takes care of logging and rejoining the inode.  This gets
rid of the NULL inode case, and allows to simplify the special
cases in the deferred operation code.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

xfs has defined PF_FSTRANS to declare a scope GFP_NOFS semantic quite
some time ago.  We would like to make this concept more generic and use
it for other filesystems as well.  Let's start by giving the flag a more
generic name PF_MEMALLOC_NOFS which is in line with an exiting
PF_MEMALLOC_NOIO already used for the same purpose for GFP_NOIO
contexts.  Replace all PF_FSTRANS usage from the xfs code in the first
step before we introduce a full API for it as xfs uses the flag directly
anyway.

This patch doesn't introduce any functional change.

Link: http://lkml.kernel.org/r/20170306131408.9828-4-mhocko@kernel.orgSigned-off-by: NMichal Hocko <mhocko@suse.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Acked-by: NVlastimil Babka <vbabka@suse.cz>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Chris Mason <clm@fb.com>
Cc: David Sterba <dsterba@suse.cz>
Cc: Jan Kara <jack@suse.cz>
Cc: Nikolay Borisov <nborisov@suse.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No one cares about the low-level helper anymore.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NDarrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>

Introduce a new ioctl that uses the reverse mapping btree to return
information about the physical layout of the filesystem.
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>

One unfortunate quirk of the reference count and reverse mapping
btrees -- they can expand in size when blocks are written to *other*
allocation groups if, say, one large extent becomes a lot of tiny
extents.  Since we don't want to start throwing errors in the middle
of CoWing, we need to reserve some blocks to handle future expansion.
The transaction block reservation counters aren't sufficient here
because we have to have a reserve of blocks in every AG, not just
somewhere in the filesystem.

Therefore, create two per-AG block reservation pools.  One feeds the
AGFL so that rmapbt expansion always succeeds, and the other feeds all
other metadata so that refcountbt expansion never fails.

Use the count of how many reserved blocks we need to have on hand to
create a virtual reservation in the AG.  Through selective clamping of
the maximum length of allocation requests and of the length of the
longest free extent, we can make it look like there's less free space
in the AG unless the reservation owner is asking for blocks.

In other words, play some accounting tricks in-core to make sure that
we always have blocks available.  On the plus side, there's nothing to
clean up if we crash, which is contrast to the strategy that the rough
draft used (actually removing extents from the freespace btrees).
Signed-off-by: NDarrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

"blocks" should be added back to fdblocks at undo time, not taken
away, i.e. the minus sign should not be used.

This is a regression introduced by commit 0d485ada ("xfs: use
generic percpu counters for free block counter"). And it's found by
code inspection, I didn't it in real world, so there's no
reproducer.
Signed-off-by: NEryu Guan <eguan@redhat.com>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

These aren't used for CIL-style logging and can be dropped.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

Merge xfs_trans_reserve and xfs_trans_alloc into a single function call
that returns a transaction with all the required log and block reservations,
and which allows passing transaction flags directly to avoid the cumbersome
_xfs_trans_alloc interface.

While we're at it we also get rid of the transaction type argument that has
been superflous since we stopped supporting the non-CIL logging mode.  The
guts of it will be removed in another patch.

[dchinner: fixed transaction leak in error path in xfs_setattr_nonsize]
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

__xfs_trans_roll() can return without setting the
*committed argument; this was a problem for xfs_bmap_finish():

        int       committed;/* xact committed or not */
...
        error = __xfs_trans_roll(tp, ip, &committed);
        if (error) {
...
                if (committed) {

and we tested an uninitialized "committed" variable on the
error path.  No caller is preserving "committed" state across
calls to __xfs_trans_roll(), so just initialize committed inside
the function to avoid future errors like this.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDave Chinner <david@fromorbit.com>

This patch modifies the stats counting macros and the callers
to those macros to properly increment, decrement, and add-to
the xfs stats counts. The counts for global and per-fs stats
are correctly advanced, and cleared by writing a "1" to the
corresponding clear file.

global counts: /sys/fs/xfs/stats/stats
per-fs counts: /sys/fs/xfs/sda*/stats/stats

global clear:  /sys/fs/xfs/stats/stats_clear
per-fs clear:  /sys/fs/xfs/sda*/stats/stats_clear

[dchinner: cleaned up macro variables, removed CONFIG_FS_PROC around
 stats structures and macros. ]
Signed-off-by: NBill O'Donnell <billodo@redhat.com>
Reviewed-by: NEric Sandeen <sandeen@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

Some callers need to make error handling decisions based on whether
the current transaction successfully committed or not. Rename
xfs_trans_roll(), add a new parameter and provide a wrapper to
preserve existing callers.
Signed-off-by: NBrian Foster <bfoster@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDave Chinner <david@fromorbit.com>

Instead of the confusing flags argument pass a boolean flag to indicate if
we want to release or regrant a log reservation.

Also ensure that xfs_log_done always drop the reference on the log ticket,
to both simplify the code and make the logic in xfs_trans_roll easier
to understand.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

The flags argument to xfs_trans_commit is not useful for most callers, as
a commit of a transaction without a permanent log reservation must pass
0 here, and all callers for a transaction with a permanent log reservation
except for xfs_trans_roll must pass XFS_TRANS_RELEASE_LOG_RES.  So remove
the flags argument from the public xfs_trans_commit interfaces, and
introduce low-level __xfs_trans_commit variant just for xfs_trans_roll
that regrants a log reservation instead of releasing it.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

xfs_trans_cancel takes two flags arguments: XFS_TRANS_RELEASE_LOG_RES and
XFS_TRANS_ABORT.  Both of them are a direct product of the transaction
state, and can be deducted:

 - any dirty transaction needs XFS_TRANS_ABORT to be properly canceled,
   and XFS_TRANS_ABORT is a noop for a transaction that is not dirty.
 - any transaction with a permanent log reservation needs
   XFS_TRANS_RELEASE_LOG_RES to be properly canceled, and passing
   XFS_TRANS_RELEASE_LOG_RES for a transaction without a permanent
   log reservation is invalid.

So just remove the flags argument and do the right thing.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

The flags value always was 0 or XFS_TRANS_ABORT.  Switch to a bool
parameter to allow further cleanups.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

We have three remaining callers of xfs_trans_dup:

 - xfs_itruncate_extents which open codes xfs_trans_roll
 - xfs_bmap_finish doesn't have an xfs_inode argument and thus leaves
   attaching them to it's callers, but otherwise is identical to
   xfs_trans_roll
 - xfs_dir_ialloc looks at the log reservations in the old xfs_trans
   structure instead of the log reservation parameters, but otherwise
   is identical to xfs_trans_roll.

By allowing a NULL xfs_inode argument to xfs_trans_roll we can switch
these three remaining users over to xfs_trans_roll and mark xfs_trans_dup
static.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

Introduce helper functions for modifying fields in the superblock
into xfs_trans.c, the only caller of xfs_mod_incore_sb_batch().  We
can then use these directly in xfs_trans_unreserve_and_mod_sb() and
so remove another user of the xfs_mode_incore_sb() API without
losing any functionality or scalability of the transaction commit
code..

Based on a patch from Christoph Hellwig.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

Add a new helper to modify the incore counter of free realtime
extents. This matches the helpers used for inode and data block
counters, and removes a significant users of the xfs_mod_incore_sb()
interface.

Based on a patch originally from Christoph Hellwig.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

XFS has hand-rolled per-cpu counters for the superblock since before
there was any generic implementation. The free block counter is
special in that it is used for ENOSPC detection outside transaction
contexts for for delayed allocation. This means that the counter
needs to be accurate at zero. The current per-cpu counter code jumps
through lots of hoops to ensure we never run past zero, but we don't
need to make all those jumps with the generic counter
implementation.

The generic counter implementation allows us to pass a "batch"
threshold at which the addition/subtraction to the counter value
will be folded back into global value under lock. We can use this
feature to reduce the batch size as we approach 0 in a very similar
manner to the existing counters and their rebalance algorithm. If we
use a batch size of 1 as we approach 0, then every addition and
subtraction will be done against the global value and hence allow
accurate detection of zero threshold crossing.

Hence we can replace the handrolled, accurate-at-zero counters with
generic percpu counters.

Note: this removes just enough of the icsb infrastructure to compile
without warnings. The rest will go in subsequent commits.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

XFS has hand-rolled per-cpu counters for the superblock since before
there was any generic implementation. The free inode counter is not
used for any limit enforcement - the per-AG free inode counters are
used during allocation to determine if there are inode available for
allocation.

Hence we don't need any of the complexity of the hand-rolled
counters and we can simply replace them with generic per-cpu
counters similar to the inode counter.

This version introduces a xfs_mod_ifree() helper function from
Christoph Hellwig.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

XFS has hand-rolled per-cpu counters for the superblock since before
there was any generic implementation. There are some warts around
the  use of them for the inode counter as the hand rolled counter is
designed to be accurate at zero, but has no specific accurracy at
any other value. This design causes problems for the maximum inode
count threshold enforcement, as there is no trigger that balances
the counters as they get close tothe maximum threshold.

Instead of designing new triggers for balancing, just replace the
handrolled per-cpu counter with a generic counter.  This enables us
to update the counter through the normal superblock modification
funtions, but rather than do that we add a xfs_mod_icount() helper
function (from Christoph Hellwig) and keep the percpu counter
outside the superblock in the struct xfs_mount.

This means we still need to initialise the per-cpu counter
specifically when we read the superblock, and vice versa when we
log/write it, but it does mean that we don't need to change any
other code.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

When the superblock is modified in a transaction, the commonly
modified fields are not actually copied to the superblock buffer to
avoid the buffer lock becoming a serialisation point. However, there
are some other operations that modify the superblock fields within
the transaction that don't directly log to the superblock but rely
on the changes to be applied during the transaction commit (to
minimise the buffer lock hold time).

When we do this, we fail to mark the buffer log item as being a
superblock buffer and that can lead to the buffer not being marked
with the corect type in the log and hence causing recovery issues.
Fix it by setting the type correctly, similar to xfs_mod_sb()...

cc: <stable@vger.kernel.org> # 3.10 to current
Tested-by: NJan Kara <jack@suse.cz>
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

More on-disk format consolidation.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

More on-disk format consolidation.  A few declarations that weren't on-disk
format related move into better suitable spots.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

Convert all the errors the core XFs code to negative error signs
like the rest of the kernel and remove all the sign conversion we
do in the interface layers.

Errors for conversion (and comparison) found via searches like:

$ git grep " E" fs/xfs
$ git grep "return E" fs/xfs
$ git grep " E[A-Z].*;$" fs/xfs

Negation points found via searches like:

$ git grep "= -[a-z,A-Z]" fs/xfs
$ git grep "return -[a-z,A-D,F-Z]" fs/xfs
$ git grep " -[a-z].*;" fs/xfs

[ with some bits I missed from Brian Foster ]
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

XFS_ERROR was designed long ago to trap return values, but it's not
runtime configurable, it's not consistently used, and we can do
similar error trapping with ftrace scripts and triggers from
userspace.

Just nuke XFS_ERROR and associated bits.
Signed-off-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

return is not a function.  "return(EIO);" is silly;
"return (EIO);" moreso.  return is not a function.
Nuke the pointless parens.

[dchinner: catch a couple of extra cases in xfs_attr_list.c,
xfs_acl.c and xfs_linux.h.]
Signed-off-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

Signed-off-by: NEric Sandeen <sandeen@redhat.com>
Reviewed-by: NDave Chinner <dchinner@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

Convert xfs_log_commit_cil() to a void function since it return nothing
but 0 in any case, after that we can simplify the relative code logic
in xfs_trans_commit() accordingly.
Signed-off-by: NJie Liu <jeff.liu@oracle.com>
Reviewed-by: NBrian Foster <bfoster@redhat.com>
Signed-off-by: NDave Chinner <david@fromorbit.com>

Currently the xfs_inode.h header has a dependency on the definition
of the BMAP btree records as the inode fork includes an array of
xfs_bmbt_rec_host_t objects in it's definition.

Move all the btree format definitions from xfs_btree.h,
xfs_bmap_btree.h, xfs_alloc_btree.h and xfs_ialloc_btree.h to
xfs_format.h to continue the process of centralising the on-disk
format definitions. With this done, the xfs inode definitions are no
longer dependent on btree header files.

The enables a massive culling of unnecessary includes, with close to
200 #include directives removed from the XFS kernel code base.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NBen Myers <bpm@sgi.com>
Signed-off-by: NBen Myers <bpm@sgi.com>

xfs_trans.h has a dependency on xfs_log.h for a couple of
structures. Most code that does transactions doesn't need to know
anything about the log, but this dependency means that they have to
include xfs_log.h. Decouple the xfs_trans.h and xfs_log.h header
files and clean up the includes to be in dependency order.

In doing this, remove the direct include of xfs_trans_reserve.h from
xfs_trans.h so that we remove the dependency between xfs_trans.h and
xfs_mount.h. Hence the xfs_trans.h include can be moved to the
indicate the actual dependencies other header files have on it.

Note that these are kernel only header files, so this does not
translate to any userspace changes at all.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NBen Myers <bpm@sgi.com>
Signed-off-by: NBen Myers <bpm@sgi.com>

The on-disk format definitions for the directory and attribute
structures are spread across 3 header files right now, only one of
which is dedicated to defining on-disk structures and their
manipulation (xfs_dir2_format.h). Pull all the format definitions
into a single header file - xfs_da_format.h - and switch all the
code over to point at that.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NBen Myers <bpm@sgi.com>
Signed-off-by: NBen Myers <bpm@sgi.com>

All of the buffer operations structures are needed to be exported
for xfs_db, so move them all to a common location rather than
spreading them all over the place. They are verifying the on-disk
format, so while xfs_format.h might be a good place, it is not part
of the on disk format.

Hence we need to create a new header file that we centralise these
related definitions. Start by moving the bffer operations
structures, and then also move all the other definitions that have
crept into xfs_log_format.h and xfs_format.h as there was no other
shared header file to put them in.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NBen Myers <bpm@sgi.com>

In optimising the CIL operations, some of the IOP_* macros for
calling log item operations were removed. Remove the rest of them as
Christoph requested.
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NGeoffrey Wehrman <gwehrman@sgi.com>
Reviewed-by: NMark Tinguely <tinguely@sgi.com>
Signed-off-by: NBen Myers <bpm@sgi.com>

With the new xfs_trans_res structure has been introduced, the log
reservation size, log count as well as log flags are pre-initialized
at mount time.  So it's time to refine xfs_trans_reserve() interface
to be more neat.

Also, introduce a new helper M_RES() to return a pointer to the
mp->m_resv structure to simplify the input.
Signed-off-by: NJie Liu <jeff.liu@oracle.com>
Signed-off-by: NDave Chinner <dchinner@redhat.com>
Reviewed-by: NMark Tinguely <tinguely@sgi.com>
Signed-off-by: NBen Myers <bpm@sgi.com>