This permits each port to select its own SCBRR calculation algorithm,
rather than having it all ifdef'ed in the header. There are presently
only 5 different variations that all parts fall under.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This moves all of the SCSCR_INIT definitions in to the platform data,
for future consolidation.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

For consistenct naming, and to allow us to fix up some confusion in the
SH-Mobile clock framework, amongst other places.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch adds TMU platform data for sh7780. Both clockevent
and clocksource support is enabled.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.

This fixes potential irq masking issues for sh7780 hardware
blocks such as SCIF/RTC/DMAC/PCIC5/MMCIF/FLCTL/GPIO
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch is based on interrupt acknowledge code for external
interrupt sources on sh3 processors and adds on sh4a processors.
Signed-off-by: NYoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.

This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch removes interrupt priority tables from the intc code.
Optimal priority assignment varies with embedded application anyway,
so keeping the interrupt priority tables together with cpu-specific
code doesn't make sense.

The function intc_set_priority() should be used instead to set the
desired interrupt priority level.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch contains the following fixes and improvements:
- Fix address typo for INTMSK2 / INTMSKCLR2 registers on sh7780.
- Adds IRQ_MODE_IRLnnnn_MASK using intc controller for IRL masking.
- Good old IRQ_MODE_IRLnnnn should not register any intc controller.
- plat_irq_setup_pins() now selects IRL or IRQ mode.
- the holding function is now disabled using ICR0.

By default all external pin interrupts are disabled.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

With the intc core improved it is now possible to put the intc data
structures in the initdata section.

Version two of this patch puts the __initdata inside DECLARE_INTC_DESC()
and removes the __initdata included in the board specific r2d code.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

We need a secondary register member in struct intc_prio_reg to support
dual priority registers used by ipi on x3.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch converts the cpu specific 7780 setup code to use the
new intc controller. Many new vectors are added and also support for
external interrupt sense configuration. So with this patch it is now
possible to configure external interrupt pins as edge or level
triggered using set_irq_type().

No external interrupts are registered by default.
Use plat_irq_setup_pins() to select between IRQ or IRL mode.

This patch also fixes the Alarm IRQ for the RTC.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This patch unifies the cpu specific interrupt setup functions for
interrupt controller blocks such as ipr, intc2 and intc. There is no
point in having separate functions for each interrupt controller, so
let's clean this up.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

The shared intc2 code currently contains cpu-specific #ifdefs.
This is a tad unclean and it prevents us from using the shared code
to drive board-specific irqs on the se7780 board.

This patch reworks the intc2 code by moving the base addresses of
the intc2 registers into struct intc2_desc. This new structure also
contains the name of the controller in struct irq_chip. The idea
behind putting struct irq_chip in there is that we can use offsetof()
to locate the base addresses in the irq_chip callbacks.

One logic change has been made - the original shared intc2 code
enabled the interrupts by default but with this patch they are all
disabled by default.
Signed-off-by: NMagnus Damm <damm@igel.co.jp>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This adds CPU support for the SH7722.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This drops the various IRQ headers that were floating around
and primarily providing hardcoded IRQ definitions for the
various CPU subtypes. This quickly got to be an unmaintainable
mess, made even more evident by the subtle breakage introduced
by the SH-2 and SH-2A changes.

Now that subtypes are able to register IRQ maps directly, just
rip all of the headers out.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

All of the various CPU subtypes currently hardcode TIMER_IRQ,
switch this to a config option in the few places we need this.

This allows further removal of hardcoded IRQ headers..
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

Currently the INTC2 code contains a fixed IRQ table that it
iterates through to set the handler type, we move this in to
the CPU subtype setup code instead and allow for submitting
the table that way.

This drops the ST40 tables, as nothing has been happening
with those processors, while converting the only existing
users to use the new table directly (SH7760 and SH7780).
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>

This cleans up quite a lot of the PCI mess that we
currently have, and attempts to consolidate the
duplication in the SH7780 and SH7751 PCI controllers.
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>