We'll need to disable/re-enable the display-side IRQs when turning
off/on the VLV display power well. Factor out the helper functions
for this. For now keep the display IRQs enabled by default, so the
functionality doesn't change. This will be changed to enable/disable
the IRQs on-demand when adding support for VLV power wells in an
upcoming patch.

v2:
- take the irq spin lock for the whole enable/disable sequence as
  these can be called with interrupts enabled
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Suggested by Daniel.

v2:
- sanitize the state checking condition, the original was rather
  confusing (partly due to the unfortunate naming of
  i915.disable_power_well) (Ville)
- simpler message+backtrace generation by using WARN instead of WARN_ON
  (Ville)
- check if always-on power wells are truly on all the time
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We need to do the same for other platforms in upcoming patches.

v2:
- s/p/pipe (Ville)
- Call the new helper with the vbl_lock already held. The part it
  protects is short, so releasing it between pipes only makes proving
  correctness more difficult.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Resolve conflict with Damien's s/p/pipe/ change.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the upcoming patches we'll need to access the rest of the fields in
the punit power gating register, so prepare for that.

v2:
- add doc reference for the power well subsystem IDs (Jesse)
- remove IDs for non-existant DPIO_RX[23] subsystems (Jesse)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This is a left-over from

commit b7e634cc
Author: Imre Deak <imre.deak@intel.com>
Date:   Tue Feb 4 21:35:45 2014 +0200

drm/i915: vlv: don't unmask IIR[DISPLAY_PIPE_A/B_VBLANK] interrupt

where we stopped unmasking the vblank IRQs, but left them enabled in the
IER register. Disable them in IER too.

v2:
- remove comment becoming stale after this change (Ville)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We can read out the pipe HW state only if the required power domain is
on. If not we consider the pipe to be off.

v2:
- no change
v3:
- push down the power domain checks into the specific crtc
  get_pipe_config handlers (Daniel)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Appease checkpatch.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Since the encoder is tied to its port, we need to make sure the power
domain for that port is on before reading out the encoder HW state.

Note that this also covers also all connector get_hw_state handlers,
since all those just call the corresponding encoder get_hw_state
handler, which checks - after this change - for all power domains
the connector needs.

v2:
- no change
v3:
- push down the power domain checks into the specific encoder
  get_hw_state handlers (Daniel)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The connector detect and get_mode handlers need to access the port
specific HW blocks to read the EDID etc. Get/put the port power domains
around these handlers.

v2:
- get port power domain for HDMI too (Ville)
- get port power domain for the DP,HDMI audio detect handlers (Jesse)
- Leave the intel_runtime_pm_get/put in the DP detect function in place.
  Instead of just removing them, these should be moved to the appropriate
  power_well enable/disable handlers. We can do this after Paulo's
  'Merge PC8 with runtime PM, v2' patchset.
v3:
- rebased on latest -nightly
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Parts that poke port specific HW blocks like the encoder HW state
readout or connector hotplug detect code need a way to check whether
required power domains are on or enable/disable these. For this purpose
add a set of power domains that refer to the port HW blocks. Get the
proper port power domains during modeset.

For now when requesting the power domain for a DDI port get it for a 4
lane configuration. This can be optimized later to request only the 2
lane power domain, when proper support is added on the VLV PHY side for
this. Atm, the PHY setup code assumes a 4 lane config in all cases.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Reading code free of special cases wins over the small overhead of
calling a noop handler. Suggested by Jesse.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Split the 'set' power well handler into an 'enable', 'disable' and
'sync_hw' handler. This maps more conveniently to higher level
operations, for example it allows us to push the hsw package c8 handling
into the corresponding hsw/bdw enable/disable handlers and the hsw BIOS
hand-over setting into the hsw/bdw sync_hw handler.

No functional change.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
[danvet: Appease checkpatch's whitespace complaints.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Whenever we request a power domain it has to guarantee that all HW
resources are enabled that are needed to access a HW register associated
with that power domain. In case a register is on an always-on power well
this won't result in turning on a power well, but it may require
enabling some other HW resource. One such resource is the HSW/BDW device
D0 state that is required for all register accesses and thus for all
power wells/power domains.

So far the init power domain (guaranteeing access to all HW registers)
was part of the default i9xx always-on power well, but not the HSW/BDW
always-on power wells. Add the domain to the latter power wells too.

Atm, all the always-on power wells have noop handlers, so this doesn't
change the functionality.

v2:
- clarify semantics of always-on power wells (Paulo)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These macros are used only locally, so move them to the .c file.

No functional change.

v2:
- add init power domain to always-on power wells in the following
  - separate - patch (Paulo)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

There are too many oustanding issues:

- Fence handling in the current code is broken. There's a patch series
  from me, but it's blocked on and extended review (which includes
  writing the testcases).

- IOMMU mapping handling is broken, we need to properly refcount it -
  currently it gets destroyed when the first vma is unbound, so way
  too early.

- There's a pending reset issue on snb. Since Mika's reset work and
  full ppgtt have been pulled in in separate branches and ended up
  intermittingly breaking each another it's unclear who's the exact
  culprit here.

- We still have persistent evidince of crazy recursion bugs through
  vma_unbind and ppgtt_relase, e.g.

  https://bugs.freedesktop.org/show_bug.cgi?id=73383

  This issue (and a few others meanwhile resolved) have blocked our
  performance measuring/tuning group since 3 months.

- Secure batch dispatching is broken. This is blocking Brad Volkin's
  command checker work since 3 months.

All these issues are confirmed to only happen when full ppgtt is
enabled, falling back to aliasing ppgtt resolves them. But even
aliasing ppgtt itself still has a regression:

- We currently unconditionally bind objects into the aliasing ppgtt,
  which means all priviledged objects like ringbuffers are visible to
  unpriviledged access again. On top of that this also breaks the
  command checker for aliasing ppgtt, since it can't hide the
  validated batch any more.

Furthermore topic/full-ppgtt has never been reviewed:

- Lifetime rules around vma unbinding/release are unclear, resulting
  into this awesome hack called ppgtt_release. Which seems to take the
  blame for most of the recursion fallout.

- Context/ring init works different on gpu reset than anywhere else.
  Such differeneces have in the past always lead to really hard to
  track down bugs.

- Aliasing ppgtt is treated in a bunch of places as a real address
  space, but it isn't - the real address space is always the global
  gtt in that case. This results in a bit a mess between contexts and
  ppgtt object, further complication the context/ppgtt/vma lifetime
  rules.

- We don't have any docs describing the overall concepts introduced
  with full ppgtt. A short, concise overview describing vmas and some
  of the strange bits around them (like the unbound vmas used by
  execbuf, or the new binding rules) really is needed.

Note that a lot of the post topic/full-ppgtt merge fallout has already
been addressed, this entire list here of 10 issues really only contains
the still outstanding issues.

Finally the 3.15 merge window is approaching and I think we need to
use the remaining time to ensure that our fallback option of using
aliasing ppgtt is in solid shape. Hence I think it's time to throw the
switch. While at it demote the helper from static inline status
because really.

Cc: Ben Widawsky <ben@bwidawsk.net>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These functions will be needed by the valleyview specific power well
update functionality added in an upcoming patch, so move them earlier.

No functional change.

v2:
- no change
v3:
- rebase on latest -nightly
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v2)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

These functions are used only by a single call site and are simple
enough to just fold them in.

Note that in later patches the parts folded in here are further
simplified as we'll remove hsw_{disable,enable}_package_c8 and the NULL
check of the power well enable/disable handlers. All this means that at
the end intel_display_power_get/put() becomes more understandable as we
don't need to jump between two functions when reading the code.

No functional change.

v2:
- clarify the rational for the change (Chris)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We have two names for the same register CHICKEN_PIPESL_1 and
HSW_PIPE_SLICE_CHICKEN_1. Unify it to just one.

Also rename the FBCQ disable bit to resemble the name we've
given to a similar bit on earlier platforms.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

gen7_enable_fbc() may write to some registers which we've already
touched, so use RMW so that we don't undo any previous updates.

Also note that we implemnt WaFbcAsynchFlipDisableFbcQueue:bdw.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Misplaced parens cause us to totally clobber the CHICKEN_PIPESL_1
registers with 0xffffffff. Move the parens to the correct place
to avoid this.

In particular this caused bit 30 of said registers to be set, which
caused the sprite CSC to produce incorrect results.

Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=72220Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

... it's this time of the year again. Originally we've frobbed this to
fix up some regressions, but maybe our DP code improved sufficiently
now that we can dare to do again what the spec recommends.

This reverts

commit 2514bc51
Author: Jesse Barnes <jbarnes@virtuousgeek.org>
Date:   Thu Jun 21 15:13:50 2012 -0700

    drm/i915: prefer wide & slow to fast & narrow in DP configs

I'm pretty sure I'll regret this patch, but otoh I expect we won't
make progress here without poking the devil occasionally.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=73694
Cc: peter@colberg.org
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: NItai BEN YAACOV <candeb@free.fr>
Tested-by: NDavid En <d.engraf@arcor.de>
Reported-and-Tested-by: NMarcus Bergner <marcusbergner@gmail.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

As we now have intel_uncore_forcewake_reset() no need
to do explicit put after reset.

v2: rebase
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

While reading some code, out of boredom, stumbled on a tiny tiny fix.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

That macro was only ever used to convert ring->private into a gem object
(hence the forceful cast). ring->private doesn't even exist anymore as
it was transmogrified by Chris in:

  commit 0d1aacac
  Author: Chris Wilson <chris@chris-wilson.co.uk>
  Date:   Mon Aug 26 20:58:11 2013 +0100

      drm/i915: Embed the ring->private within the struct intel_ring_buffer
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Its last usage outside of i915_gem.c was removed in:

  commit 1f70999f
  Author: Chris Wilson <chris@chris-wilson.co.uk>
  Date:   Mon Jan 27 22:43:07 2014 +0000

     drm/i915: Prevent recursion by retiring requests when the ring is full
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch fixes the blank screen bug introduced in 3.14-rc1 on the
MacBook Air 6,2. The comments state that we need to force edp vdd so
lets put it back.

The regression was introduced by the following commit:

commit dff392db
Author: Paulo Zanoni <paulo.r.zanoni@intel.com>
Date:   Fri Dec 6 17:32:41 2013 -0200

    drm/i915: don't touch the VDD when disabling the panel

v2: Wrap intel_disable_dp() with _vdd_on and _vdd_off

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74628
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NPatrik Jakobsson <patrik.r.jakobsson@gmail.com>
Acked-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

In the future, we need to be able to specify per-pipe number of
planes/sprites. Let's start today!
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This macro is similar to for_each_pipe() we already have. Convert the
two call sites we have at the same time.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Consistency throughout the code base is good and remove some room for
mistakes (as explained in the "drm/i915: Use a pipe variable to cycle
through the pipes" commit)

So, let's replace the for_each_pipe(i) occurences by for_each_pipe(pipe)
when it's reasonable and practical to do so (eg. when there isn't another
pipe variable already).
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

'i' is already defined in the function scope and used elsewhere. Let's
use it instead.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I recently fumbled a patch because I wrote twice num_sprites[i], and it
was the right thing to do in only 50% of the cases.

This patch ensures I need to write num_sprites[pipe], ie it should be
self-documented that it's per-pipe number of sprites without having to
look at what is 'i' this time around.

It's all a lame excuse, but it does make it harder to redo the same
mistake.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

According to BSpec we need to always set this magic bit in ring buffer
mode.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If we need precisely N lanes to satisfy the FDI bandwidth requirement,
the code would still claim that we need N+1 lanes. Use DIV_ROUND_UP()
to get a more accurate answer.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On DDI there's no PLL as such to generate the pixel clock for VGA.
Instead we derive the pixel clock from the FDI link frequency. So
to make .compute_config match what .get_config does, we need to
set the port_clock based on the FDI link frequency.

Note that we don't even check the port_clock when selecting the
PLL for VGA output. We just assume SPLL at 1.35GHz is what we want,
and that does match with the asumption of FDI frequency of 2.7Ghz
we have in intel_fdi_link_freq().

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=74955Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NPaulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

as they don't exists.

v2: rename gen6_*_mt_* to gen7_*_mt_* as they never get called
    with gen6 (Chris)
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Ben Widawsky <ben@bwidawsk.net> (v1)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When we get control from BIOS there might be mt forcewake
bits already set. This causes us to do double mt get
without proper clear/ack sequence.

Fix this by clearing mt forcewake register on init,
like we do with older gens.
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

BDW is no longer flagged as preliminary hw, but without
i915.preliminary_hw_support module param set the logs are filled with
WARNs about it.

Just make semaphores off the BDW per-chip default for now.

CC: Ben Widawsky <ben@bwidawsk.net>
Reported-by: NSebastien Dufour <sebastien.dufour@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Ben and I believe this will be necessary on production hardware.
Signed-off-by: NKenneth Graunke <kenneth@whitecape.org>
[danvet: Shuffle lines to group all ROW_CHICKEN writes and add a
cautious comment that this might not be needed on production hw.]
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I believe this will be necessary on production hardware.
Signed-off-by: NKenneth Graunke <kenneth@whitecape.org>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
[danvet: Fix whitespace fail spotted by checkpatch. Also add missing
:bdw w/a tag that Ville spotted.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>