Add support for the ab9540 variant of the ab8500 family.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Cc: Avinash Kumar <avinash.kumar@stericsson.com>
Cc: Thirupathi Chippakurthy <thirupathi.chippakurthy@stericsson.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add support for the ab8540 variant of the ab8500 family.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Cc: Avinash Kumar <avinash.kumar@stericsson.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Introduce a "flags" field in "struct ab8500_usb" to allow controlling
driver features and quirks depending on ab8500 chip variant and
revision.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Move each chip's PHY tuning value set code to a separate function to
improve code readability.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add an initial platform_device_id table to the ab8500-usb driver to
allow probing additional variants of the ab8500 family chips.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The driver supports both ab8500 and ab8505, but the actual phy tuning
values logic sets ab8500 values:

if (!is_ab8500_2p0_or_earlier(ab->ab8500))

which is supposed to set values for ab8500, but incorrectly results true
for ab8505 too.

Fix this by adding an additional is_ab8500(ab->ab8500) check.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add an ab8500_usb_restart_phy() function called during probe to ensure
that the AB8500 USB phy is initialized properly even when a cable is
connected at probe time.

Without this fix subsequent host reconnections are not detected
properly.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NSakethram Bommisetti <sakethram.bommisetti@stericsson.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add common clock support code for the ab8500-usb phy driver.
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Various non functional coding style fixes on ux500_dma.c and
phy-ab8500-usb.c drivers.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NMaxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Host side dma support for ux500 is enabled by piggybacking on Inventra
dma support.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMian Yousaf Kaukab <mian.yousaf.kaukab@stericsson.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The streaming endpoint bandwidth parameters are computed are runtime
from module parameters. Remove the corresponding static initializers.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

With the hcd is now a direct member of struct musb, we can now simply
eliminate the musb_to_hcd() macro. There aren't that many users left
anyway, as some where already fixed up when parts were factored out to
musb_host.c
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Initialize the host and gadget subsystems of the musb driver only when
the appropriate mode is selected from platform data, or device-tree
information, respectively.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Define MUSB_PORT_MODE_{HOST,GADGET,DUAL_ROLE} and store the
platform-specified value in struct musb.

Note that MUSB_PORT_MODE_HOST has to be set to 1 in order to match
existing device tree bindings which are already documented but in fact
unusued. For information on the bindings, please refer to

  Documentation/devicetree/bindings/usb/omap-usb.txt
  Documentation/devicetree/bindings/usb/am33xx-usb.txt
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch re-introduces the bits that are necessary to use the musb
controller in host mode.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This makes building the actual object files optional to the selected
mode, which saves users who know which kind of USB mode support they
need some binary size.

Unimplemented functions are stubbed out with static inline functions.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The musb struct is currently allocated along with the hcd, which makes
it difficult to build a driver that only acts as gadget device.

Fix this by allocating musb directly, and keep the hcd around as
a pointer in the musb struct.

struct hc_driver musb_hc_driver can now also be static to musb_host.c,
and the macro musb_to_hcd() is just a pointer dereferencer for now, and
will be eliminated later.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This function has its only user in musb_virthub.c, so let's move it
there and make it static.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This will be done from a more appropriate location and as it doesn't
work anyway, it can safely be removed before the other changes.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In particular, this introduces musb_host_resume_root_hub()and
musb_host_poke_root_hub() which will be stubbed out later.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Let the function declarations live in the header files they belong to,
which makes it easier to stub them out later.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The functionality meant to be represented by this symbol will be
re-added later, but for now, USB_GADGET_MUSB_HDRC is in fact unused and
can be dropped.
Signed-off-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This was related to an old bug on early versions
of TUSB6010 which we don't support anymore.

It's known to cause issues on several other
situations with more recent devices so we
better remove this flag now and come up
with a better workaround should one be deemed
necessary.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We can't simply pass the resource pointer from our
device down to our children, otherwise module
reinsertion will not work as the resource will
continue to be marked as busy.

Fix it by building a proper struct resource for
our child musb device.
Tested-by: NDmitry Lifshitz <lifshitz@compulab.co.il>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

do_smart_update_queue() is called when an operation (semop,
semctl(SETVAL), semctl(SETALL), ...) modified the array.  It must check
which of the sleeping tasks can proceed.

do_smart_update_queue() missed a few wakeups:
 - if a sleeping complex op was completed, then all per-semaphore queues
   must be scanned - not only those that were modified by *sops
 - if a sleeping simple op proceeded, then the global queue must be
   scanned again

And:
 - the test for "|sops == NULL) before scanning the global queue is not
   required: If the global queue is empty, then it doesn't need to be
   scanned - regardless of the reason for calling do_smart_update_queue()

The patch is not optimized, i.e.  even completing a wait-for-zero
operation causes a rescan.  This is done to keep the patch as simple as
possible.
Signed-off-by: NManfred Spraul <manfred@colorfullife.com>
Acked-by: NDavidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull NFS client bugfixes from Trond Myklebust:

 - Stable fix to prevent an rpc_task wakeup race
 - Fix a NFSv4.1 session drain deadlock
 - Fix a NFSv4/v4.1 mount regression when not running rpc.gssd
 - Ensure auth_gss pipe detection works in namespaces
 - Fix SETCLIENTID fallback if rpcsec_gss is not available

* tag 'nfs-for-3.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS: Fix SETCLIENTID fallback if GSS is not available
  SUNRPC: Prevent an rpc_task wakeup race
  NFSv4.1 Fix a pNFS session draining deadlock
  SUNRPC: Convert auth_gss pipe detection to work in namespaces
  SUNRPC: Faster detection if gssd is actually running
  SUNRPC: Fix a bug in gss_create_upcall

Pull amd64 edac fix from Borislav Petkov:
 "A sysfs file permissions correction"

* tag 'edac_fixes_for_3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
  amd64_edac: Fix bogus sysfs file permissions

Pull parisc fixes from Helge Deller:
 "This time we made the kernel- and interruption stack allocation
  reentrant which fixed some strange kernel crashes (specifically
  protection ID traps).

  Furthemore this patchset fixes the interrupt stack in UP and SMP
  configurations by using native locking instructions.  And finally
  usage of floating point calculations on parisc were disabled in the
  MPILIB."

* 'parisc-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
  parisc: fix irq stack on UP and SMP
  parisc/superio: Use module_pci_driver to register driver
  parisc: make interrupt and interruption stack allocation reentrant
  parisc: show number of FPE and unaligned access handler calls in /proc/interrupts
  parisc: add additional parisc git tree to MAINTAINERS file
  parisc: use PAGE_SHIFT instead of hardcoded value 12 in pacache.S
  parisc: add rp5470 entry to machine database
  MPILIB: disable usage of floating point registers on parisc

Pull xfs fixes from Ben Myers:
 "Here are fixes for corruption on 512 byte filesystems, a rounding
  error, a use-after-free, some flags to fix lockdep reports, and
  several fixes related to CRCs.  We have a somewhat larger post -rc1
  queue than usual due to fixes related to the CRC feature we merged for
  3.10:

   - Fix for corruption with FSX on 512 byte blocksize filesystems
   - Fix rounding error in xfs_free_file_space
   - Fix use-after-free with extent free intents
   - Add several missing KM_NOFS flags to fix lockdep reports
   - Several fixes for CRC related code"

* tag 'for-linus-v3.10-rc3' of git://oss.sgi.com/xfs/xfs:
  xfs: remote attribute lookups require the value length
  xfs: xfs_attr_shortform_allfit() does not handle attr3 format.
  xfs: xfs_da3_node_read_verify() doesn't handle XFS_ATTR3_LEAF_MAGIC
  xfs: fix missing KM_NOFS tags to keep lockdep happy
  xfs: Don't reference the EFI after it is freed
  xfs: fix rounding in xfs_free_file_space
  xfs: fix sub-page blocksize data integrity writes

Pull bettery fixes from Anton Vorontsov:
 "Last minute one-liners: wrong kfree usage fix, module alias fixup and
  kconfig adjustments"

* tag 'for-v3.10-fixes' of git://git.infradead.org/battery-2.6:
  pm2301_charger: Fix module alias prefix
  wm831x_backup: Fix wrong kfree call for devdata->backup.name
  bq27x00: Fix I2C dependency in KConfig
  lp8788-charger: Fix kconfig dependency

Pull power management and ACPI fixes from Rafael Wysocki:

 - Additional CPU ID for the intel_pstate driver from Dirk Brandewie.

 - More cpufreq fixes related to ARM big.LITTLE support and locking from
   Viresh Kumar.

 - VIA C7 cpufreq build fix from Rafał Bilski.

 - ACPI power management fix making it possible to use device power
   states regardless of the CONFIG_PM setting from Rafael J Wysocki.

 - New ACPI video blacklist item from Bastian Triller.

* tag 'pm+acpi-3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / video: Add "Asus UL30A" to ACPI video detect blacklist
  cpufreq: arm_big_little_dt: Instantiate as platform_driver
  cpufreq: arm_big_little_dt: Register driver only if DT has valid data
  cpufreq / e_powersaver: Fix linker error when ACPI processor is a module
  cpufreq / intel_pstate: Add additional supported CPU ID
  cpufreq: Drop rwsem lock around CPUFREQ_GOV_POLICY_EXIT
  ACPI / PM: Allow device power states to be used for CONFIG_PM unset

Pull slave-dma fixes from Vinod Koul:
 "We have two patches from Andy & Rafael fixing the Lynxpoint dma"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  ACPI / LPSS: register clock device for Lynxpoint DMA properly
  dma: acpi-dma: parse CSRT to extract additional resources

kcore_vmalloc is in fs/proc/kcore.c and kcore_mem is unused across
the tree. Noticed while grepping the tree for some other kcore stuff.

(score looks pretty unmaintained to me.)
Signed-off-by: NKyle McMartin <kyle@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull ARC fixes from Vineet Gupta:

 - Fallouts/wreckage of Cache Flush optimizations / aliasing dcache
   support

 - Fix for an interesting bug where piped input to grep was getting
   mysteriously clobbered

* tag 'arc-v3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
  ARC: lazy dcache flush broke gdb in non-aliasing configs
  ARC: Use enough bits for determining page's cache color
  ARC: Brown paper bag bug in macro for checking cache color
  ARC: copy_(to|from)_user() to honor usermode-access permissions
  ARC: [mm] Prevent stray dcache lines after__sync_icache_dcach()
  ARC: [TB10x] Remove redundant abilis,simple-pinctrl mechanism

Pull ARM fixes from Russell King:
 "Just three this time, all really quite small"

* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
  ARM: 7729/1: vfp: ensure VFP_arch is non-zero when VFP is not supported
  ARM: 7727/1: remove the .vm_mm value from gate_vma
  ARM: 7723/1: crypto: sha1-armv4-large.S: fix SP handling

gdbserver inserting a breakpoint ends up calling copy_user_page() for a
code page. The generic version of which (non-aliasing config) didn't set
the PG_arch_1 bit hence update_mmu_cache() didn't sync dcache/icache for
corresponding dynamic loader code page - causing garbade to be executed.

So now aliasing versions of copy_user_highpage()/clear_page() are made
default. There is no significant overhead since all of special alias
handling code is compiled out for non-aliasing build
Signed-off-by: NVineet Gupta <vgupta@synopsys.com>

Merge fixes from Andrew Morton:
 "A bunch of fixes and one simple fbdev driver which missed the merge
  window because people will still talking about it (to no great
  effect)."

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (30 commits)
  aio: fix kioctx not being freed after cancellation at exit time
  mm/pagewalk.c: walk_page_range should avoid VM_PFNMAP areas
  drivers/rtc/rtc-max8998.c: check for pdata presence before dereferencing
  ocfs2: goto out_unlock if ocfs2_get_clusters_nocache() failed in ocfs2_fiemap()
  random: fix accounting race condition with lockless irq entropy_count update
  drivers/char/random.c: fix priming of last_data
  mm/memory_hotplug.c: fix printk format warnings
  nilfs2: fix issue of nilfs_set_page_dirty() for page at EOF boundary
  drivers/block/brd.c: fix brd_lookup_page() race
  fbdev: FB_GOLDFISH should depend on HAS_DMA
  drivers/rtc/rtc-pl031.c: pass correct pointer to free_irq()
  auditfilter.c: fix kernel-doc warnings
  aio: fix io_getevents documentation
  revert "selftest: add simple test for soft-dirty bit"
  drivers/leds/leds-ot200.c: fix error caused by shifted mask
  mm/THP: use pmd_populate() to update the pmd with pgtable_t pointer
  linux/kernel.h: fix kernel-doc warning
  mm compaction: fix of improper cache flush in migration code
  rapidio/tsi721: fix bug in MSI interrupt handling
  hfs: avoid crash in hfs_bnode_create
  ...

Pull ARM SoC fixes from Olof Johansson:
 "We didn't have any fixes sent up for -rc2, so this is a slightly
  larger batch.  A bit all over the place platform-wise; OMAP, at91,
  marvell, renesas, sunxi, ux500, etc.

  I tried to summarize highlights but there isn't a whole lot to point
  out.  Lots of little things fixed all over.  A couple of defconfig
  updates due to new/changing options."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
  ARM: at91/sama5: fix incorrect PMC pcr div definition
  ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition
  ARM: at91: at91sam9n12: move external irq declatation to DT
  ARM: shmobile: marzen: Use error values in usb_power_*
  ARM: tegra: defconfig fixes
  ARM: nomadik: fix IRQ assignment for SMC ethernet
  ARM: vt8500: Add missing NULL terminator in dt_compat
  clk: tegra: add ac97 controller clock
  clk: tegra: remove USB from clk init table
  ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache node
  ARM: plat-orion: Fix num_resources and id for ge10 and ge11
  ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
  SERIAL: OMAP: Remove the slave idle handling from the driver
  ARM: OMAP2+: serial: Remove the un-used slave idle hooks
  ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
  ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
  ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
  arm: mvebu: fix the 'ranges' property to handle PCIe
  ARM: mvebu: select ARCH_REQUIRE_GPIOLIB for mvebu platform
  ARM: AM33XX: Add missing .clkdm_name to clkdiv32k_ick clock
  ...

The recent changes overhauling fs/aio.c introduced a bug that results in
the kioctx not being freed when outstanding kiocbs are cancelled at
exit_aio() time.  Specifically, a kiocb that is cancelled has its
completion events discarded by batch_complete_aio(), which then fails to
wake up the process stuck in free_ioctx().  Fix this by modifying the
wait_event() condition in free_ioctx() appropriately.

This patch was tested with the cancel operation in the thread based code
posted yesterday.

[akpm@linux-foundation.org: fix build]
Signed-off-by: NBenjamin LaHaise <bcrl@kvack.org>
Signed-off-by: NKent Overstreet <koverstreet@google.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Zach Brown <zab@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>