SPC(Serial Power Controller) on TC2 also controls the CPU performance
operating points which is essential to provide CPU DVFS. The M3
microcontroller provides two sets of eight performance values, one set
for each cluster (CA15 or CA7). Each of this value contains the
frequency(kHz) and voltage(mV) at that performance level. It expects
these performance level to be passed through the SPC PERF_LVL registers.

This patch adds support to populate these performance levels from M3,
build the mapping to CPU OPPs at the boot and then use it to get and
set the CPU performance level runtime.
Signed-off-by: NSudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Acked-by: NPawel Moll <Pawel.Moll@arm.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Currently, the prototype of cpufreq_drivers target routines is:

int target(struct cpufreq_policy *policy, unsigned int target_freq,
		unsigned int relation);

And most of the drivers call cpufreq_frequency_table_target() to get a valid
index of their frequency table which is closest to the target_freq. And they
don't use target_freq and relation after that.

So, it makes sense to just do this work in cpufreq core before calling
cpufreq_frequency_table_target() and simply pass index instead. But this can be
done only with drivers which expose their frequency table with cpufreq core. For
others we need to stick with the old prototype of target() until those drivers
are converted to expose frequency tables.

This patch implements the new light weight prototype for target_index() routine.
It looks like this:

int target_index(struct cpufreq_policy *policy, unsigned int index);

CPUFreq core will call cpufreq_frequency_table_target() before calling this
routine and pass index to it. Because CPUFreq core now requires to call routines
present in freq_table.c CONFIG_CPU_FREQ_TABLE must be enabled all the time.

This also marks target() interface as deprecated. So, that new drivers avoid
using it. And Documentation is updated accordingly.

It also converts existing .target() to newly defined light weight
.target_index() routine for many driver.
Acked-by: NHans-Christian Egtvedt <egtvedt@samfundet.no>
Acked-by: NJesper Nilsson <jesper.nilsson@axis.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NRussell King <linux@arm.linux.org.uk>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rjw@rjwysocki.net>

Since Operating Performance Points (OPP) functions are specific
to device specific power management, be specific and rename opp.h
to pm_opp.h
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Since Operating Performance Points (OPP) data structures are specific
to device specific power management, be specific and rename opp_* data
structures in OPP library with dev_pm_opp_* equivalent.

Affected structures are:
 struct opp
 enum opp_event

Minor checkpatch warning resulting of this change was fixed as well.
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Since Operating Performance Points (OPP) functions are specific to
device specific power management, be specific and rename opp_*
accessors in OPP library with dev_pm_opp_* equivalent.

Affected functions are:
 opp_get_voltage
 opp_get_freq
 opp_get_opp_count
 opp_find_freq_exact
 opp_find_freq_floor
 opp_find_freq_ceil
 opp_add
 opp_enable
 opp_disable
 opp_get_notifier
 opp_init_cpufreq_table
 opp_free_cpufreq_table
Reported-by: NRandy Dunlap <rdunlap@infradead.org>
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Fix build breakage introduced by commit 22c8b4f1 (cpufreq: sa11x0:
Expose frequency table).

[rjw: Changelog]
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

CONFIG_CPU_FREQ_TABLE will be always enabled when cpufreq framework is used, as
cpufreq core depends on it. So, we don't need this CONFIG option anymore as it
is not configurable. Remove CONFIG_CPU_FREQ_TABLE and update its users.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Most of the CPUFreq drivers do similar things in .exit() and .verify() routines
and .attr. So its better if we have generic routines for them which can be used
by cpufreq drivers then.

This patch uses these generic routines in the sa11x0 driver.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

This reverts commit 10bcdfb8. There is
no consensus on the bindings for the reserved memory, so the code for
handing it will be reverted.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NGrant Likely <grant.likely@linaro.org>

In ftrace_syscall_enter(),
    syscall_get_arguments(..., 0, n, ...)
        if (i == 0) { <handle ORIG_r0> ...; n--;}
        memcpy(..., n * sizeof(args[0]));
If 'number of arguments(n)' is zero and 'argument index(i)' is also zero in
syscall_get_arguments(), none of arguments should be copied by memcpy().
Otherwise 'n--' can be a big positive number and unexpected amount of data
will be copied. Tracing system calls which take no argument, say sync(void),
may hit this case and eventually make the system corrupted.
This patch fixes the issue both in syscall_get_arguments() and
syscall_set_arguments().

Cc: <stable@vger.kernel.org>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NAKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Without the "clock-frequency" property in arch timer node, could able
to see the below crash dump.

[<c0014e28>] (unwind_backtrace+0x0/0xf4) from [<c0011808>] (show_stack+0x10/0x14)
[<c0011808>] (show_stack+0x10/0x14) from [<c036ac1c>] (dump_stack+0x7c/0xb0)
[<c036ac1c>] (dump_stack+0x7c/0xb0) from [<c01ab760>] (Ldiv0_64+0x8/0x18)
[<c01ab760>] (Ldiv0_64+0x8/0x18) from [<c0062f60>] (clockevents_config.part.2+0x1c/0x74)
[<c0062f60>] (clockevents_config.part.2+0x1c/0x74) from [<c0062fd8>] (clockevents_config_and_register+0x20/0x2c)
[<c0062fd8>] (clockevents_config_and_register+0x20/0x2c) from [<c02b8e8c>] (arch_timer_setup+0xa8/0x134)
[<c02b8e8c>] (arch_timer_setup+0xa8/0x134) from [<c04b47b4>] (arch_timer_init+0x1f4/0x24c)
[<c04b47b4>] (arch_timer_init+0x1f4/0x24c) from [<c04b40d8>] (clocksource_of_init+0x34/0x58)
[<c04b40d8>] (clocksource_of_init+0x34/0x58) from [<c049ed8c>] (time_init+0x20/0x2c)
[<c049ed8c>] (time_init+0x20/0x2c) from [<c049b95c>] (start_kernel+0x1e0/0x39c)

THis is because the Exynos u-boot, for example on the Chromebooks, doesn't set
up the CNTFRQ register as expected by arch_timer. Instead, we have to specify
the frequency in the device tree like this.
Signed-off-by: NYuvaraj Kumar C D <yuvaraj.cd@samsung.com>
[olof: Changed subject, added comment, elaborated on commit message]
Signed-off-by: NOlof Johansson <olof@lixom.net>

Fengguang Wu, Oleg Nesterov and Peter Zijlstra tracked down
a kernel crash to a GCC bug: GCC miscompiles certain 'asm goto'
constructs, as outlined here:

  http://gcc.gnu.org/bugzilla/show_bug.cgi?id=58670

Implement a workaround suggested by Jakub Jelinek.
Reported-and-tested-by: NFengguang Wu <fengguang.wu@intel.com>
Reported-by: NOleg Nesterov <oleg@redhat.com>
Reported-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Suggested-by: NJakub Jelinek <jakub@redhat.com>
Reviewed-by: NRichard Henderson <rth@twiddle.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: <stable@kernel.org>
Signed-off-by: NIngo Molnar <mingo@kernel.org>

File drivers/leds/leds-lp55xx-common.c refuse to change led_current sysfs
attribute if value is higher than max_current specified in board file. By default
global C variables are zero, so changing always failed. This patch adding missing
max_current and setting it to max safe value 100 (10 mA).

It is unclear which commit exactly caused this regression as the lp5523
driver was broken and was hiding the platform data breakage. Now
the driver is fixed so this should be fixed as well.
Signed-off-by: NPali Rohár <pali.rohar@gmail.com>
Signed-off-by: NJoerg Reisenweber <joerg@openmoko.org>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: NTony Lindgren <tony@atomide.com>

Since dra7 reuses the  function 'omap5_realtime_timer_init' in
arch/arm/mach-omap2/board-generic.c as timer init function, it has to be
built for this SoC as well.
Signed-off-by: NSimon Barth <Simon.Pe.Barth@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The wake-up interrupt bit is available on omap3/4/5 processors
unlike what we claim. Without fixing it we cannot use it on
omap3 and the system configured for wake-up events will just
hang on wake-up.

Cc: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Benoît Cousson <bcousson@baylibre.com>
Cc: devicetree@vger.kernel.org
Signed-off-by: NTony Lindgren <tony@atomide.com>

SoC family definitions at the moment are reactive to board needs
as a result, beagle-xm would matchup with ti,omap3 which invokes
omap3430_init_early instead of omap3630_init_early. Obviously, this is
the wrong behavior.

With clock node dts conversion, we get the following warnings before
system hangs as a result and 3630 based platforms fails to boot
(uart4 clocks are only present in OMAP3630 and not present in
OMAP3430):

...
omap_hwmod: uart4: cannot clk_get main_clk uart4_fck
omap_hwmod: uart4: cannot _init_clocks

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2434
_init+0x6c/0x80()
omap_hwmod: uart4: couldn't init clocks
...

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: timer12: enabled state can only be entered from
initialized, idle, or disabled state
...

WARNING: CPU: 0 PID: 46 at arch/arm/mach-omap2/omap_hwmod.c:2224
_idle+0xd4/0xf8()
omap_hwmod: timer12: idle state can only be entered from enabled state

WARNING: CPU: 0 PID: 1 at arch/arm/mach-omap2/omap_hwmod.c:2126
_enable+0x254/0x280()
omap_hwmod: uart4: enabled state can only be entered from
initialized, idle, or disabled state

So, add specific compatiblity for 3630 to allow match for Beagle-XM
platform.
Signed-off-by: NNishanth Menon <nm@ti.com>
[tony@atomide.com: left out ti,omap343x, updated comments]
Signed-off-by: NTony Lindgren <tony@atomide.com>

With DT-based boot, the GPMC OneNAND sync mode setup does not work
correctly. During the async mode setup, sync flags gets incorrectly
set in the onenand_async data and the system crashes during the async
setup. Also, the sync mode never gets set in gpmc_onenand_data->flags, so
even without the crash, the actual sync mode setup would never be called.

The patch fixes this by adjusting the gpmc_onenand_data->flags when the
data is read from the DT. Also while doing this we force the onenand_async
to be always async.

The patch enables to use the following DTS chunk (that should correspond
the arch/arm/mach-omap2/board-rm680.c board file setup) with Nokia N950,
which currently crashes with 3.12-rc1. The crash output can be also
found below.

&gpmc {
	ranges = <0 0 0x04000000 0x20000000>;

	onenand@0,0 {
		#address-cells = <1>;
		#size-cells = <1>;
		reg = <0 0 0x20000000>;

		gpmc,sync-read;
		gpmc,sync-write;
		gpmc,burst-length = <16>;
		gpmc,burst-read;
		gpmc,burst-wrap;
		gpmc,burst-write;
		gpmc,device-width = <2>;
		gpmc,mux-add-data = <2>;
		gpmc,cs-on-ns = <0>;
		gpmc,cs-rd-off-ns = <87>;
		gpmc,cs-wr-off-ns = <87>;
		gpmc,adv-on-ns = <0>;
		gpmc,adv-rd-off-ns = <10>;
		gpmc,adv-wr-off-ns = <10>;
		gpmc,oe-on-ns = <15>;
		gpmc,oe-off-ns = <87>;
		gpmc,we-on-ns = <0>;
		gpmc,we-off-ns = <87>;
		gpmc,rd-cycle-ns = <112>;
		gpmc,wr-cycle-ns = <112>;
		gpmc,access-ns = <81>;
		gpmc,page-burst-access-ns = <15>;
		gpmc,bus-turnaround-ns = <0>;
		gpmc,cycle2cycle-delay-ns = <0>;
		gpmc,wait-monitoring-ns = <0>;
		gpmc,clk-activation-ns = <5>;
		gpmc,wr-data-mux-bus-ns = <30>;
		gpmc,wr-access-ns = <81>;
		gpmc,sync-clk-ps = <15000>;
	};
};

[    1.467559] GPMC CS0: cs_on     :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    1.474822] GPMC CS0: cs_rd_off :   1 ticks,   5 ns (was  24 ticks)   5 ns
[    1.482116] GPMC CS0: cs_wr_off :  14 ticks,  71 ns (was  24 ticks)  71 ns
[    1.489349] GPMC CS0: adv_on    :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    1.496582] GPMC CS0: adv_rd_off:   3 ticks,  15 ns (was   3 ticks)  15 ns
[    1.503845] GPMC CS0: adv_wr_off:   3 ticks,  15 ns (was   3 ticks)  15 ns
[    1.511077] GPMC CS0: oe_on     :   3 ticks,  15 ns (was   4 ticks)  15 ns
[    1.518310] GPMC CS0: oe_off    :   1 ticks,   5 ns (was  24 ticks)   5 ns
[    1.525543] GPMC CS0: we_on     :   0 ticks,   0 ns (was   0 ticks)   0 ns
[    1.532806] GPMC CS0: we_off    :   8 ticks,  40 ns (was  24 ticks)  40 ns
[    1.540039] GPMC CS0: rd_cycle  :   4 ticks,  20 ns (was  29 ticks)  20 ns
[    1.547302] GPMC CS0: wr_cycle  :   4 ticks,  20 ns (was  29 ticks)  20 ns
[    1.554504] GPMC CS0: access    :   0 ticks,   0 ns (was  23 ticks)   0 ns
[    1.561767] GPMC CS0: page_burst_access:   0 ticks,   0 ns (was   3 ticks)   0 ns
[    1.569641] GPMC CS0: bus_turnaround:   0 ticks,   0 ns (was   0 ticks)   0 ns
[    1.577270] GPMC CS0: cycle2cycle_delay:   0 ticks,   0 ns (was   0 ticks)   0 ns
[    1.585144] GPMC CS0: wait_monitoring:   0 ticks,   0 ns (was   0 ticks)   0 ns
[    1.592834] GPMC CS0: clk_activation:   0 ticks,   0 ns (was   0 ticks)   0 ns
[    1.600463] GPMC CS0: wr_data_mux_bus:   5 ticks,  25 ns (was   8 ticks)  25 ns
[    1.608154] GPMC CS0: wr_access :   0 ticks,   0 ns (was  23 ticks)   0 ns
[    1.615386] GPMC CS0 CLK period is 5 ns (div 1)
[    1.625122] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf009e442
[    1.633178] Internal error: : 1008 [#1] ARM
[    1.637573] Modules linked in:
[    1.640777] CPU: 0 PID: 1 Comm: swapper Not tainted 3.12.0-rc1-n9xx-los.git-5318619-00006-g4baa700-dirty #26
[    1.651123] task: ef04c000 ti: ef050000 task.ti: ef050000
[    1.656799] PC is at gpmc_onenand_setup+0x98/0x1e0
[    1.661865] LR is at gpmc_cs_set_timings+0x494/0x5a4
[    1.667083] pc : [<c002e040>]    lr : [<c001f384>]    psr: 60000113
[    1.667083] sp : ef051d10  ip : ef051ce0  fp : ef051d94
[    1.679138] r10: c0caaf60  r9 : ef050000  r8 : ef18b32c
[    1.684631] r7 : f0080000  r6 : c0caaf60  r5 : 00000000  r4 : f009e400
[    1.691497] r3 : f009e442  r2 : 80050000  r1 : 00000014  r0 : 00000000
[    1.698333] Flags: nZCv  IRQs on  FIQs on  Mode SVC_32  ISA ARM  Segment kernel
[    1.706024] Control: 10c5387d  Table: af290019  DAC: 00000015
[    1.712066] Process swapper (pid: 1, stack limit = 0xef050240)
[    1.718200] Stack: (0xef051d10 to 0xef052000)
[    1.722778] 1d00:                                     00004000 00001402 00000000 00000005
[    1.731384] 1d20: 00000047 00000000 0000000f 0000000f 00000000 00000028 0000000f 00000005
[    1.739990] 1d40: 00000000 00000000 00000014 00000014 00000000 00000000 00000000 00000000
[    1.748596] 1d60: 00000000 00000019 00000000 00000000 ef18b000 ef099c50 c0c8cb30 00000000
[    1.757171] 1d80: c0488074 c048f868 ef051dcc ef051d98 c024447c c002dfb4 00000000 c048f868
[    1.765777] 1da0: 00000000 00000000 c010e4a4 c0dbbb7c c0c8cb40 00000000 c0ca2500 c0488074
[    1.774383] 1dc0: ef051ddc ef051dd0 c01fd508 c0244370 ef051dfc ef051de0 c01fc204 c01fd4f4
[    1.782989] 1de0: c0c8cb40 c0ca2500 c0c8cb74 00000000 ef051e1c ef051e00 c01fc3b0 c01fc104
[    1.791595] 1e00: ef0983bc 00000000 c0ca2500 c01fc31c ef051e44 ef051e20 c01fa794 c01fc328
[    1.800201] 1e20: ef03634c ef0983b0 ef27d534 c0ca2500 ef27d500 c0c9a2f8 ef051e54 ef051e48
[    1.808807] 1e40: c01fbcfc c01fa744 ef051e84 ef051e58 c01fb838 c01fbce4 c0411df8 c0caa040
[    1.817413] 1e60: ef051e84 c0ca2500 00000006 c0caa040 00000066 c0488074 ef051e9c ef051e88
[    1.825988] 1e80: c01fca30 c01fb768 c04975b8 00000006 ef051eac ef051ea0 c01fd728 c01fc9bc
[    1.834594] 1ea0: ef051ebc ef051eb0 c048808c c01fd6e4 ef051f4c ef051ec0 c0008888 c0488080
[    1.843200] 1ec0: 0000006f c046bae8 00000000 00000000 ef051efc ef051ee0 ef051f04 ef051ee8
[    1.851806] 1ee0: c046d400 c0181218 c046d410 c18da8d5 c036a8e4 00000066 ef051f4c ef051f08
[    1.860412] 1f00: c004b9a8 c046d41c c048f840 00000006 00000006 c046b488 00000000 c043ec08
[    1.869018] 1f20: ef051f4c c04975b8 00000006 c0caa040 00000066 c046d410 c048f85c c048f868
[    1.877593] 1f40: ef051f94 ef051f50 c046db8c c00087a0 00000006 00000006 c046d410 ffffffff
[    1.886199] 1f60: ffffffff ffffffff ffffffff 00000000 c0348fd0 00000000 00000000 00000000
[    1.894805] 1f80: 00000000 00000000 ef051fac ef051f98 c0348fe0 c046daa8 00000000 00000000
[    1.903411] 1fa0: 00000000 ef051fb0 c000e7f8 c0348fdc 00000000 00000000 00000000 00000000
[    1.912017] 1fc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    1.920623] 1fe0: 00000000 00000000 00000000 00000000 00000013 00000000 ffffffff ffffffff
[    1.929199] Backtrace:
[    1.931793] [<c002dfa8>] (gpmc_onenand_setup+0x0/0x1e0) from [<c024447c>] (omap2_onenand_probe+0x118/0x49c)
[    1.942047] [<c0244364>] (omap2_onenand_probe+0x0/0x49c) from [<c01fd508>] (platform_drv_probe+0x20/0x24)
[    1.952117]  r8:c0488074 r7:c0ca2500 r6:00000000 r5:c0c8cb40 r4:c0dbbb7c
[    1.959197] [<c01fd4e8>] (platform_drv_probe+0x0/0x24) from [<c01fc204>] (driver_probe_device+0x10c/0x224)
[    1.969360] [<c01fc0f8>] (driver_probe_device+0x0/0x224) from [<c01fc3b0>] (__driver_attach+0x94/0x98)
[    1.979125]  r7:00000000 r6:c0c8cb74 r5:c0ca2500 r4:c0c8cb40
[    1.985107] [<c01fc31c>] (__driver_attach+0x0/0x98) from [<c01fa794>] (bus_for_each_dev+0x5c/0x90)
[    1.994506]  r6:c01fc31c r5:c0ca2500 r4:00000000 r3:ef0983bc
[    2.000488] [<c01fa738>] (bus_for_each_dev+0x0/0x90) from [<c01fbcfc>] (driver_attach+0x24/0x28)
[    2.009735]  r6:c0c9a2f8 r5:ef27d500 r4:c0ca2500
[    2.014587] [<c01fbcd8>] (driver_attach+0x0/0x28) from [<c01fb838>] (bus_add_driver+0xdc/0x260)
[    2.023742] [<c01fb75c>] (bus_add_driver+0x0/0x260) from [<c01fca30>] (driver_register+0x80/0xfc)
[    2.033081]  r8:c0488074 r7:00000066 r6:c0caa040 r5:00000006 r4:c0ca2500
[    2.040161] [<c01fc9b0>] (driver_register+0x0/0xfc) from [<c01fd728>] (__platform_driver_register+0x50/0x64)
[    2.050476]  r5:00000006 r4:c04975b8
[    2.054260] [<c01fd6d8>] (__platform_driver_register+0x0/0x64) from [<c048808c>] (omap2_onenand_driver_init+0x18/0x20)
[    2.065490] [<c0488074>] (omap2_onenand_driver_init+0x0/0x20) from [<c0008888>] (do_one_initcall+0xf4/0x150)
[    2.075836] [<c0008794>] (do_one_initcall+0x0/0x150) from [<c046db8c>] (kernel_init_freeable+0xf0/0x1b4)
[    2.085815] [<c046da9c>] (kernel_init_freeable+0x0/0x1b4) from [<c0348fe0>] (kernel_init+0x10/0xec)
[    2.095336] [<c0348fd0>] (kernel_init+0x0/0xec) from [<c000e7f8>] (ret_from_fork+0x14/0x3c)
[    2.104125]  r4:00000000 r3:00000000
[    2.107879] Code: ebffc3ae e2505000 ba00002e e2843042 (e1d320b0)
[    2.114318] ---[ end trace b8ee3e3e5e002451 ]---
Signed-off-by: NAaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The generic code is well equipped to differentiate between
SMP and UP configurations.However, there are some devices which
use Cortex-A9 MP core IP with 1 CPU as configuration. To let
these SOCs to co-exist in a CONFIG_SMP=y build by leveraging
the SMP_ON_UP support, we need to additionally check the
number the cores in Cortex-A9 MPCore configuration. Without
such a check in place, the startup code tries to execute
ALT_SMP() set of instructions which lead to CPU faults.

The issue was spotted on TI's Aegis device and this patch
makes now the device work with omap2plus_defconfig which
enables SMP by default. The change is kept limited to only
Cortex-A9 MPCore detection code.

Note that if any future SoC *does* use 0x0 as the PERIPH_BASE, then
the SCU address check code needs to be #ifdef'd for for the Aegis
platform.
Acked-by: NSricharan R <r.sricharan@ti.com>
Signed-off-by: NVaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This fixes a regression for kernels after v3.2

After commit 72662e01
ARM: head.S: only include __turn_mmu_on in the initial identity mapping

Zaurus PXA devices call sharpsl_save_param() during fixup and hang on
boot because memcpy refers to physical addresses no longer valid if the
MMU is setup.
Zaurus collie (SA1100) is unaffected (function is called in init_machine).

The code was making assumptions and for PXA the virtual address
should have been used before.
Signed-off-by: NMarko Katic <dromede@gmail.com>
Signed-off-by: NAndrea Adami <andrea.adami@gmail.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Commit 09096f6a (ARM: 7822/1: add workaround for ambiguous C99 stdint.h
types) introduced an ARM specific 'asm/types.h' to work around some
ambiguities in the definitions of 32 bit types. Hence, we will not be
needing the generic version anymore.
Signed-off-by: NArd Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Currently mcpm_cpu_power_down() and mcpm_cpu_suspend() trigger BUG()
if mcpm_platform_register() is not called beforehand.  This may occur
for many reasons such as some incomplete device tree passed to the kernel
or the like.

Let's be nicer to users and avoid killing the kernel if that happens by
logging a warning and returning to the caller.  The mcpm_cpu_suspend()
user is already set to deal with this situation, and so is cpu_die()
invoking mcpm_cpu_die().

The problematic case would have been the B.L switcher's usage of
mcpm_cpu_power_down(), however it has to call mcpm_cpu_power_up() first
which is already set to catch an error resulting from a missing
mcpm_platform_register() call.
Signed-off-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Turn on SDHCI for i.MX support so machines can boot with local rootfs
on SD. Tested on a Wandboard Quad.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Reviewed-by: NFabio Estevam <fabio.estevam@freescale.com>

Install targets (install, zinstall, uinstall) on arm have a dependency
to vmlinux. This may cause parts of the kernel to be rebuilt during
installation. We must avoid this since this may run as root. Install
targets "ABSOLUTELY MUST NOT MODIFY THE SOURCE TREE." as Linus
emphasized this in:

 http://lkml.org/lkml/2013/7/10/600

So on arm and maybe other archs we need the same as for x86:

 1648e4f8 x86, kbuild: make "make install" not depend on vmlinux

This patch fixes this for arm. Dependencies are removed and instead a
check to install.sh is added for the files that are needed.

This issue was uncovered by this build error where the -j option is
used in conjunction with install targets:

 $ make <makeflags>
 $ make <makeflags> zinstall
 ...
   DEPMOD
 Usage: .../scripts/depmod.sh /sbin/depmod <kernelrelease>

(INSTALL_MOD_PATH and INSTALL_PATH variables set, so no root perms
required in this case.)

The problem is that zinstall on arm due to its dependency to vmlinux
does a prepare/prepare3 and finally does a forced rewrite of
kernel.release even if it exists already.

Rebuilding kernel.release removes it first and then recreates it. This
might race with another parallel make job running depmod.

So this patch should fix this one too.

Also quoting $(KERNELRELEASE) arg for install.sh as this messes
argument order in case it is empty (which is the case if the kernel
was not built yet).
Signed-off-by: NRobert Richter <robert.richter@linaro.org>
Signed-off-by: NRobert Richter <rric@kernel.org>
Acked-by: Michal Marek <mmarek@suse.cz>.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: N"Yann E. MORIN" <yann.morin.1998@free.fr>
Signed-off-by: NMichal Marek <mmarek@suse.cz>

... otherwise it is impossible for the low level iommu driver to
figure out which pte flags should be used.

In __map_sg_chunk we can derive the flags from dma_data_direction.

In __iommu_create_mapping we should treat the memory like
DMA_BIDIRECTIONAL and pass both IOMMU_READ and IOMMU_WRITE to
iommu_map.
__iommu_create_mapping is used during dma_alloc_coherent (via
arm_iommu_alloc_attrs).  AFAIK dma_alloc_coherent is responsible for
allocation _and_ mapping.  I think this implies that access to the
mapped pages should be allowed.

Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NAndreas Herrmann <andreas.herrmann@calxeda.com>
Acked-by: NWill Deacon <will.deacon@arm.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>

When 5e12a613 and 0cd3754a were introduced, Netgear ReadyNAS 102 .dts
file was queued for inclusion and missed the update to have Mbus (and
then BootROM) ranges properties declared. It also missed the relocation
of Armada 370/XP PCIe DT nodes introduced by 14fd8ed0 after de1af8d4.
This patch fixes that which makes 3.12-rc3 bootable on the NAS.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

This patch exposes sa11x0's frequency table to cpufreq core. It always existed
but not as an array frequencies and not in the format cpufreq core wants it to.
Also it was present in the unit of 100kHz earlier which is made consistent with
cpufreq core now, i.e. kHz.
Signed-off-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Like we are doing on DDR0 we need to cleanly shutdown DDR1 if it is
used before rebooting.
If DDR1 is not initialized, we check it and avoid dereferencing its address.
Even by adding two more instructions, we are able to complete the procedure
within a single cache line.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

HWMOD removal for MMC is breaking edma_start as the events are being manually
triggered due to unused channel list not being clear.

The above issue is fixed by reading the "dmas" property from the DT node if it
exists and clearing the bits in the unused channel list if the dma controller
used by any device is EDMA. For this purpose we use the of_* helpers to parse
the arguments in the dmas phandle list.

Also introduced is a minor clean up of a checkpatch error in old code.
Reviewed-by: NSekhar Nori <nsekhar@ti.com>
Reported-by: NBalaji T K <balajitk@ti.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Nishanth Menon <nm@ti.com>
Cc: Pantel Antoniou <panto@antoniou-consulting.com>
Cc: Jason Kridner <jkridner@beagleboard.org>
Cc: Koen Kooi <koen@dominion.thruhere.net>
Signed-off-by: NJoel Fernandes <joelf@ti.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

On the TC2 testchip, when all CPUs in a cluster enter standbywfi
and commit a power down request, the power controller will wait
for standbywfil2 coming from L2 cache controller to shut the
cluster down.
By the time all CPUs in a cluster commit a power down request
and enter wfi, the power controller cannot backtrack, or put it
another way, a CPU must not be allowed to complete execution
independently of the power controller, the only way for it to
resume properly must be upon wake-up IRQ pending and subsequent
reset triggered from the power controller.

Current MCPM back-end for TC2 disables the GIC CPU IF only when
power down is committed through the tc2_pm_suspend() method, that
makes sense since a suspended CPU is still online and can receive
interrupts whereas a hotplugged CPU, since it is offline,
migrated all IRQs and shutdown the per-CPU peripherals, hence
their PPIs.

The flaw with this reasoning is the following. If all CPUs in
a clusters are entering a power down state either through CPU
idle or CPU hotplug, when the last man successfully completes
the MCPM power down sequence (and executes wfi), power controller
waits for L2 wfi signal to quiesce the cluster and shut it down.
If, when all CPUs are sitting in wfi, an online CPU hotplugs back
in one of the CPUs in the cluster being shutdown, that CPU
receives an IPI that causes wfi to complete (since tc2_pm_down()
method does not disable the GIC CPU IF in that case - CPU being
hotplugged out, not idle) and the power controller will never see
the stanbywfil2 signal coming from L2 that is required for
shutdown to happen and the system deadlocks.

Further to this issue, kexec hotplugs secondary CPUs out during
kernel reload/restart.
Because kexec may (deliberately) trash the old kernel text, it is
not OK for CPUs to follow the MCPM soft reboot path, since
instructions after the WFI may have been replaced by kexec.

If tc2_pm_down() does not disable the GIC cpu interface, there is a
race between CPU powerdown in the old kernel and the IPI from the
new kernel that triggers secondary boot, particularly if the
powerdown is slow (due to L2 cache cleaning for example).  If the
new kernel wins the race, the affected CPU(s) will not really be
reset and may execute garbage after the WFI.

The only solution to this problem consists in disabling the GIC
CPU IF on a CPU committed to power down regardless of the power
down entry method (CPU hotplug or CPU idle). This way, CPU wake-up
is under power controller control, which prevents unexpected wfi
exit caused by a pending IRQ.

This patch moves the GIC CPU IF disable call in the TC2 MCPM
implementation from the tc2_pm_suspend() method to the
tc2_pm_down() method to fix the mentioned race condition(s).
Reviewed-by: NDave Martin <Dave.Martin@arm.com>
Tested-by: Dave Martin <Dave.Martin@arm.com> (for kexec)
Signed-off-by: NSudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: NNicolas Pitre <nico@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

the current dts is lacking interrupt and dma prop for video input
processor of prima2 and atlas6, this patch fixes it.
Signed-off-by: NRenwei Wu <Renwei.Wu@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

we lost an address range <0x56000000 0x56000000 0x1b00000> for peri-iobg
of prima2.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Makefile missed to include atlas6-evb.dtb for ARCH_ATLAS6.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

sirf uart and usp-based uart driver with full dma support has
hit 3.12, here we fix the fifosize, dma channels for some HW
prop.
Signed-off-by: NQipan Li <Qipan.Li@csr.com>
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Without that fix, at the end of the shutdown process, the board is
still powered (led glowing, fan running, ...).
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

NETGEAR ReadyNAS 102 Power button definition in .dts file flags
associated GPIO active low instead of active high. This results
in reversed events reported by input subsystem (0 returned when
the button is pressed, 1 when released). This patch makes
associated GPIO active high to recover correct behaviour.
Signed-off-by: NArnaud Ebalard <arno@natisbad.org>
Signed-off-by: NJason Cooper <jason@lakedaemon.net>

ad65782f (context_tracking: Optimize main APIs off case
with static key) converted context tracking main APIs to inline
function and left ARM asm callers behind.

This can be easily fixed by making ARM calling the post static
keys context tracking function. We just need to replicate the
static key checks there. We'll remove these later when ARM will
support the context tracking static keys.
Reported-by: NGuenter Roeck <linux@roeck-us.net>
Reported-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NFrederic Weisbecker <fweisbec@gmail.com>
Tested-by: NKevin Hilman <khilman@linaro.org>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Cc: Anil Kumar <anilk4.v@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kevin Hilman <khilman@linaro.org>

This fixes a compile error where CONFIG_PCI is disabled:

  LD      init/built-in.o
arch/arm/mach-integrator/built-in.o: In function `ap_map_io':
integrator_cp.c:(.init.text+0x570): undefined reference to `pci_v3_early_init'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2

Cc: stable@vger.kernel.org
Signed-off-by: NJoerg Roedel <joro@8bytes.org>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

cpu_reset is already #defined in <asm/proc-fns.h> as processor.reset,
so it expands here and causes problems.

Cc: <stable@vger.kernel.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NChristoffer Dall <christoffer.dall@linaro.org>

This property is no longer required by the GPIO binding. Remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>

e5c9b4cd ("sh_eth: get R8A7740 support
out of #ifdef") exchanged sh-eth driver name to r8a7740-gether, but,
eva_pinctrl_map[] didn't follow it. Fixes it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>