This uses the new API for tagging GPIO lines as in use by
IRQs. This enforces a few semantic checks on how the underlying
GPIO line is used.

Cc: Haojian Zhuang <haojian.zhuang@linaro.org>
Cc: Deepak Sikri <deepak.sikri@st.com>
Acked-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This makes the PL061 driver print proper error messages
when probe fails, and also tell us when the chip is finally
registered.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

'lp3943_gpio_of_match' is always compiled in. Hence the
helper macro is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

This is one of LP3943 MFD driver.
LP3943 is configurable as a GPIO expander, up to 16 GPIOs.

* Application note: how to configure LP3943 as a GPIO expander
  http://www.ti.com/lit/an/snva287a/snva287a.pdf

* Supported GPIO controller operations
  request, free, direction_input, direction_output, get and set

* GPIO direction register not supported
  LP3943 doesn't have the GPIO direction register. It only provides input and
  output status registers.
  So, private data for the direction should be handled manually.
  This variable is updated whenever the direction is changed and
  used in 'get' operation.

* Pin assignment
  A driver data, 'pin_used' is checked when a GPIO is requested.
  If the GPIO is already assigned, then returns as failure.
  If the GPIO is available, 'pin_used' is set.
  When the GPIO is not used anymore, then it is cleared.
  It is defined as unsigned long type for atomic bit operation APIs,
  but only LSB 16bits are used because LP3943 has 16 outputs.
Signed-off-by: NMilo Kim <milo.kim@ti.com>
Reviewed-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NLee Jones <lee.jones@linaro.org>

Signed-off-by: NSeongJae Park <sj38.park@gmail.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The MCP drivers fails to compile on trial builds due to missing
Kconfig dependency on OF_GPIO. Fix it.

Cc: Lars Poeschel <poeschel@lemonage.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This adds interrupt functionality for i2c chips to the driver.
They can act as a interrupt-controller and generate interrupts, if
the inputs change.
This is tested with a mcp23017 chip on an arm based platform.

v3:
- be a bit more clear that the irq functionality is also available
  on spi versions of the chips, but the linux driver does not support
  this yet

v2:
- some more word about irq-mirror property in binding doc
- use of_read_bool instead of of_find_property for
  "interrupt-contrller" and "irq-mirror"
- cache the "interrupt-controller" for remove function
- do set the irq-mirror bit only if device is marked as
  interrupt-controller
- do create the irq mapping and setup of irq_desc of all possible
  interrupts in probe path instead of in gpio_to_irq
- mark gpios as in use as interrupts in irq in irq_startup and
  unlock it in irq_shutdown
- rename virq to child_irq
- remove dev argument from mcp23s08_irq_setup function
- move gpiochip_add before mcp23s08_irq_setup in probe path
Signed-off-by: NLars Poeschel <poeschel@lemonage.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

gpio-samsung.h header file introduced by commit 93177be0910c
("ARM: S3C[24|64]xx: move includes back under <mach/> scope")
is required only by S3C[24|64]xx machines. Include them conditionally
to avoid the following build errors for other machine configurations.
drivers/gpio/gpio-samsung.c:35:31: fatal error: mach/gpio-samsung.h: No such file or directory
arch/arm/plat-samsung/pm-gpio.c:22:31: fatal error: mach/gpio-samsung.h: No such file or directory
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

It would be convenient to normalize the return value for gpio_get.

I have checked mach-mmp / mach-pxa / plat-pxa / plat-orion / mach-orion5x.
It's OK for all of them to change this function to return 0 and 1.
Signed-off-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

When refactoring and breaking out the includes for the
machine-specific GPIO configuration, two files were created
in <linux/platform_data/gpio-samsung-s3c[24|64]xx.h>, but as
that namespace shall be used for defining data exchanged
between machines and drivers, using it for these broad macros
and config settings is wrong.

Move the headers back into the machine-local
<mach/gpio-samsung.h> file and think about the next step.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: linux-samsung-soc@vger.kernel.org
Acked-by: NMark Brown <broonie@linaro.org>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Now that all users of acpi_gpio.h have been moved to use either the GPIO
descriptor interface or to the internal gpiolib.h we can get rid of
acpi_gpio.h entirely.

Once this is done the only interface to get GPIOs to drivers enumerated
from ACPI namespace is the descriptor based interface.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Instead of asking each driver to register to ACPI events we can just call
acpi_gpiochip_register_interrupts() for each chip that has an ACPI handle.
The function checks chip->to_irq and if it is set to NULL (a GPIO driver
that doesn't do interrupts) the function does nothing.

We also add the a new header drivers/gpio/gpiolib.h that is used for
functions internal to gpiolib and add ACPI GPIO chip registering functions
to that header.

Once that is done we can remove call to acpi_gpiochip_register_interrupts()
from its only user, pinctrl-baytrail.c
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Since request_muxed_region() is used to synchronize access on the
Super-I/O controller, then the can_sleep attribute must be set for
the f7188x GPIO chips.
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The contents of this header file are not referenced in the driver.
Remove its inclusion.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Prevent build failure when the selected variant does not support GPIO32.
Acked-by: NMax Filippov <jcmvbkbc@gmail.com>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This helps increasing build testing coverage.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There is no reason to keep the OF data if the driver was compiled
without DT support.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

'tb10x_gpio_dt_ids' is always compiled in. Hence the
helper macro is not needed.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Return the appropriate error code instead of hardcoding it.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Silences the following warning:
why not propagate 'port->irq' from platform_get_irq() instead of (-22)?
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Driver core sets it to NULL upon probe failure or release.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Some GPIO line limits are incorrectly set which, for instance,
does not allow nRTS1 (GPH11) configuration on a S3C2416 chip.
Signed-off-by: NJosé Miguel Gonçalves <jose.goncalves@inov.pt>
Reviewed-by: NHeiko Stuebner <heiko@sntech.de>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

The system may crash if:
- there are more than 1 banks
- unbanked irqs are enabled
- someone will call gpio_to_irq() for GPIO from bank2 or above

Hence, fix it by not creating irq_domain if unbanked irqs are enabled
and correct gpio_to_irq_banked() to handle this properly.

Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

It's unsafe to call IRQ chip callbacks (.irq_mask/irq_unmask/irq_ack)
from chained IRQ handler directly. Because, Davinci GPIO block is used
by different SoCs, which, in turn, have different Main IRQ controllers
(Davinci - aintc, cp-intc; Keystone - arm-gic) which may introduce
diffrent set of IRQ chip callbacks. As result, call of
gpio_irq_handler() on Keysone will simply cause crash the system,
because ARM-GIC implements .irq_eoi() instead of .irq_ack().

Hence, fix it by using Kernel chained_irq_enter/chained_irq_exit APIs as
they are intended to handle exact such cases.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This patch adds OF parser support for davinci gpio
driver and also appropriate documentation in gpio-davinci.txt
located at Documentation/devicetree/bindings/gpio/.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NKV Sujith <sujithkv@ti.com>
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
[prabhakar.csengg@gmail.com: simplified the OF code, removed
		unnecessary DT property and also simplified
		the commit message]
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Convert the davinci gpio driver to use irqdomain support.
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
[grygorii.strashko@ti.com:
 - switch to use one irq-domain per  all GPIO banks
 - keep irq_create_mapping() call in gpio_to_irq_banked() as it
   simply transformed to irq_find_mapping() if IRQ mapping exist
   already]
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

The compatible to Davinci GPIO HW block is used by other TI SoCs, like
Keystone, where GPIO support is declared as optional.

Hence, introduce GPIO_DAVINCI Kconfig option which will allow to enable
Davinci GPIO driver for Keystone SoCs when needed. At same time, kept
Davinci GPIO driver enabled for Davinci SoCs by default.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Since Davinci GPIO driver is moved to support gpiolib it has to use
ARCH_NR_GPIOS (can be configured using CONFIG_ARCH_NR_GPIO Kconfig
option) configuration instead of any mach/platform specific options.

Hence, replace private DAVINCI_N_GPIO with common ARCH_NR_GPIOS. This is
safe because default value for ARCH_NR_GPIOS=256 and maximum number of
supported GPIOs for Davinci is DAVINCI_N_GPIO=144.

More over, this is one of steps to re-use Davinci GPIO driver by other
mach/platform.
Signed-off-by: NGrygorii Strashko <grygorii.strashko@ti.com>
Acked-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

This patch replaces the __raw_readl/writel with
{readl|writel}_relaxed(), Altough the code runs on ARMv5
based SOCs, changing this will help using code for other
use cases (like with big-endian machines).
Signed-off-by: NLad, Prabhakar <prabhakar.csengg@gmail.com>
Acked-by: NLinus Walleij <linus.walleij@xxxxxxxxxx>
Signed-off-by: NSekhar Nori <nsekhar@ti.com>

Compilation failed on some platforms due to implicit inclusion of
<linux/io.h>, make this dependency explicit.
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This isolates the custom S3C64xx GPIO definition table to
<linux/platform_data/gpio-samsung-s3x64xx.h> as this is
used in a few different places in the kernel, removing the
need to depend on the implicit inclusion of <mach/gpio.h>
from <linux/gpio.h> and thus getting rid of a few nasty
cross-dependencies.

Also delete the CONFIG_SAMSUNG_GPIO_EXTRA stuff. Instead
roof the number of GPIOs for this platform:
First sum up all the GPIO banks from A to Q: 187 GPIOs.
Add the 16 "board GPIOs" and the roof for SAMSUNG_GPIO_EXTRA,
128, so in total maximum 187+16+128 = 331 GPIOs, so let's
take the same roof as for S3C24XX: 512. This way we can do
away with the GPIO calculation macros for GPIO_BOARD_START,
BOARD_NR_GPIOS and the definition of ARCH_NR_GPIOS.

Cc: Mark Brown <broonie@kernel.org>
[on Mini6410 board]
Tested-by: NTomasz Figa <t.figa@samsung.com>
[for changes in mach-s3c64xx]
Acked-by: NTomasz Figa <t.figa@samsung.com>
Tested-by: NMark Brown <broonie@linaro.org>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This isolates the custom S3C24xx GPIO definition table to
<linux/platform_data/gpio-samsung-s3x24xx.h> as this is
used in a few different places in the kernel, removing the
need to depend on the implicit inclusion of <mach/gpio.h>
from <linux/gpio.h> and thus getting rid of a few nasty
cross-dependencies.

We also delete the nifty CONFIG_S3C24XX_GPIO_EXTRA stuff.
The biggest this can ever be for the S3C24XX is
CONFIG_S3C24XX_GPIO_EXTRA = 128, and then for CPU_S3C2443 or
CPU_S3C2416 32*12 GPIOs are added, so 32*12+128 = 512
is the absolute roof value on this platform. So we set
the size of ARCH_NR_GPIO to this and the GPIOs array will
fit any S3C24XX platform, as per pattern from other archs.

ChangeLog v2->v3:
- Move the movement of the S3C64XX gpio.h file out of
  this patch and into the follow-up patch where it belongs.
ChangeLog v1->v2:
- Added an #ifdef ARCH_S3C24XX around the header inclusion
  in drivers/gpio/gpio-samsung.c as we would otherwise
  have colliding definitions when compiling S3C64XX.
- Rename inclusion guard in the header file.

Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Sylwester Nawrocki <sylvester.nawrocki@gmail.com>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: linux-samsung-soc@vger.kernel.org
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Acked-by: NHeiko Stuebner <heiko@sntech.de>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Fix to return a negative error code from the error handling
case instead of 0.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Add missing .owner of struct gpio_chip. This prevents the
module from being removed from underneath its users.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This patch adds support for the GPIOs found on the SMSC "Super I/
SCH311x.

The chip detection and I/O functions are copied from sch311x_wdt.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

Doing this allows drivers to distinguish between a real error case (if
there was an error when we tried to resolve the GPIO) and when the optional
GPIO line was not available.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: NAlexandre Courbot <acourbot@nvidia.com>
Acked-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

According to the manual, if a port is set for level detection using
the corresponding bit in the edge/level select register and an external
level interrupt signal is asserted, the corresponding bit in INTDT
does not use the FF to hold the input.
Thus, writing 1 to the corresponding bits in INTCLR cannot clear the
corresponding bits in the INTDT register. Instead, when an external
input signal is stopped, the corresponding bit in INTDT is cleared
automatically.

Since the INTDT bit cannot be cleared for the level interrupts until
the interrupt signal is stopped, we end up with the infinite loop
when using deferred (threaded) IRQ handling.

Since a deferred interrupt is disabled by the low-level handler and
re-enabled only when the deferred handler is completed, Fix the issue
by dropping disabled interrupts from the pending mask as suggested by
Laurent Pinchart <laurent.pinchart@ideasonboard.com>

Changes in V2:
* Drop disabled interrupts from pending mask altogether instead of
  dropping level interrupts one by one once they get handled.
Signed-off-by: NValentine Barshak <valentine.barshak@cogentembedded.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NMagnus Damm <damm@opensource.se>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

This allows the module to be loaded automatically.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>

We should be writing bits here but instead we're writing the
numbers that correspond to the bits we want to write. Fix it by
wrapping the numbers in the BIT() macro. This fixes gpios acting
as interrupts.

Cc: stable@vger.kernel.org
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>