Document the core of the debugfs CEC error injection ABI.

The driver specific commands are documented elsewhere and
this file points to that documentation.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The CEC Pin framework adds support for Error Injection.

Document all the error injections commands and how to use it.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

It turns out that the struct cec_fh event buffer size of 64 events
(64 for CEC_EVENT_PIN_CEC_LOW and 64 for _HIGH) is too small. It's
about 160 ms worth of events and if the Raspberry Pi is busy, then it
might take too long for the application to be scheduled so that it can
drain the pending events. Increase these buffers to 800 events which
is at least 2 seconds worth of events.

There is also a FIFO in between the interrupt and the cec-pin thread.
The thread passes the events on to the CEC core. It is important that
should this FIFO fill up the cec core will be informed that events
have been lost so this can be communicated to the user by setting
CEC_EVENT_FL_DROPPED_EVENTS.

It is very hard to debug CEC problems if events were lost without
informing the user of that fact.

If events were dropped due to the FIFO filling up, then the debugfs
status file will let you know how many events were dropped.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Keep track of the number of short or long start bits, the number
of short or long data bits and the number of initiated or detected
low drive conditions.

Show this information in the status debugfs log.

Helpful when debugging, particularly when doing error injection
as well.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Implement all the error injection commands.

The state machine gets new states for the various error situations,
helper functions are added to detect whether an error injection is
active and the actual error injections are implemented.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add support to the CEC Pin framework to parse error injection commands
and to show them.

The next patch will do the actual implementation of this.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This function will be needed for injecting a custom pulse.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Document the new core error injection callbacks.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add two new ops (error_inj_show and error_inj_parse_line) to support
error injection functionality for CEC adapters. If both are present,
then the core will add a new error-inj debugfs file that can be used
to see the current error injection commands and to set error injection
commands.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This protocol was recently added and causes warnings.
Signed-off-by: NSean Young <sean@mess.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The values of enc_y_addr and enc_c_addr are initialized by
s5p_mfc_hw_call(), but, in thesis, this macro might be doing
nothing, if the get_enc_frame_buffer() is not declared.
That causes those GCC warnings:

	drivers/media/platform/s5p-mfc/s5p_mfc_enc.c:1242 enc_post_frame_start() error: uninitialized symbol 'enc_y_addr'.
	drivers/media/platform/s5p-mfc/s5p_mfc_enc.c:1243 enc_post_frame_start() error: uninitialized symbol 'enc_c_addr'.
	drivers/media/platform/s5p-mfc/s5p_mfc_enc.c:1256 enc_post_frame_start() error: uninitialized symbol 'enc_y_addr'.
	drivers/media/platform/s5p-mfc/s5p_mfc_enc.c:1257 enc_post_frame_start() error: uninitialized symbol 'enc_c_addr'.

Change the logic by initializing those constants to zero,
with should hopefully do the right thing.
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Valid range for those controls is specified in documentation as [0, 51],
so initialize the controls to such range rather than [INT_MIN, INT_MAX].
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

When value of V4L2_CID_MPEG_VIDEO_HEVC_MIN_QP or V4L2_CID_MPEG_VIDEO_HEVC_MAX_QP
controls is changed we should update range of a set of HEVC quantization
parameter v4l2 controls as specified in the HEVC controls documentation.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Provide proper (real) struct device to request_firmware() call. This fixes
following error messages:

(NULL device *): Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2
(NULL device *): Direct firmware load for s5p-mfc-v6.fw failed with error -2

into a bit more meaningful ones:

s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6-v2.fw failed with error -2
s5p-mfc 11000000.codec: Direct firmware load for s5p-mfc-v6.fw failed with error -2
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add HEVC encoder support and necessary registers, V4L2 CIDs,
and hevc encoder parameters
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add support for codec definition and corresponding buffer
requirements for VP9 decoder.
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add support for codec definition and corresponding buffer
requirements for HEVC decoder.
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Aligning the luma_dpb_size, chroma_dpb_size, mv_size and me_buffer_size
for MFCv10.10.
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NKamil Debski <kamil@wypas.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

After MFC v8.0, mfc f/w lets the driver know how much scratch buffer
size is required for decoder. If mfc f/w has the functionality,
E_MIN_SCRATCH_BUFFER_SIZE, driver can know how much scratch buffer size
is required for encoder too.
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Adding the support for MFC v10.10, with new register file and
necessary hw control, decoder, encoder and structural changes.
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This patch renames macro IS_MFCV8 to IS_MFCV8_PLUS so that the MFCv8
code can be resued for MFCv10.10 support. Since the MFCv8 specific code
holds good for MFC v10.10 also.
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Acked-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

LaTeX adjustbox is known to cause pdf documentation build breakages
with some newer Sphinx versions. So, don't use it.

While here, adjust table sizes in order to better produce the
pdf output.

Fixes: c0da55b9 ("media: v4l2: Documentation for HEVC CIDs")
Cc: Smitha T Murthy <smitha.t@samsung.com>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Added V4L2 controls for HEVC encoder.

with V4L2_MPEG_VIDEO_HEVC_PROFILE_MAIN_10 to match the code.

[s.nawrocki@samsung.com]: Replaced V4L2_MPEG_VIDEO_HEVC_PROFILE_MAIN10
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add v4l2 controls for HEVC encoder
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add V4L2 definition for HEVC compressed format which is also
known as H.265.
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NStanimir Varbanov <stanimir.varbanov@linaro.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

HEVC is a video coding format
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Reviewed-by: NStanimir Varbanov <stanimir.varbanov@linaro.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Add V4L2 definition for HEVC compressed format
Signed-off-by: NSmitha T Murthy <smitha.t@samsung.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NStanimir Varbanov <stanimir.varbanov@linaro.org>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Instead of switching capture mode depending on how many buffers are
available use a scratch buffer and always run in continuous mode. By
using a scratch buffer the responsiveness of the capture loop is
increased as it can keep running even if there are no buffers available
from userspace.

As soon as a userspace queues a buffer it is inserted into the capture
loop and returned as soon as it is filled. This is a improvement on the
previous logic where the whole capture loop was stopped and switched to
single capture mode if userspace did not feed the VIN driver buffers at
the same time it consumed them. To make matters worse it was difficult
for the driver to reenter continuous mode if it entered single mode even
if userspace started to queue buffers faster. This resulted in
suboptimal performance where if userspace where delayed for a short
period the ongoing capture would be slowed down and run in single mode
until the capturing process where restarted.

An additional effect of this change is that the capture logic can be
made much simple as we know that continuous mode will always be used.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NJacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Before starting a capture, allocate a scratch buffer which can be used
by the driver to give to the hardware if no buffers are available from
userspace. The buffer is not used in this patch but prepares for future
refactoring where the scratch buffer can be used to avoid the need to
fallback on single capture mode if userspace can't queue buffers as fast
as the VIN driver consumes them.
Signed-off-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: NJacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: NKieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

:c:type:: -> :c:type:
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Multpiple -> Multiple
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Acked-by: NSteve Longerbeam <steve_longerbeam@mentor.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The newly added pdev variable is only used in an #ifdef, causing a
build warning without CONFIG_PCI_MSI, unless we move the declaration
inside the same #ifdef:

drivers/media/pci/ngene/ngene-core.c: In function 'ngene_start':
drivers/media/pci/ngene/ngene-core.c:1328:17: error: unused variable 'pdev' [-Werror=unused-variable]

Fixes: 6795bf62 ("media: ngene: convert kernellog printing from printk() to dev_*() macros")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NDaniel Scheller <d.scheller@gmx.net>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

We now get a warning after the 'dmadev' variable is no longer used:

drivers/media/platform/omap/omap_vout_vrfb.c: In function 'omap_vout_prepare_vrfb':
drivers/media/platform/omap/omap_vout_vrfb.c:239:21: error: unused variable 'dmadev' [-Werror=unused-variable]

Fixes: 8f0aa382 ("media: v4l: omap_vout: vrfb: Use the wrapper for prep_interleaved_dma()")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Reviewed-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

When loading the budget_av driver for ie. a KNC1 DVB-C TDA10024 card,
which makes use of the ttpci eeprom check functionality (that always
fails on these cards, but that's no issue at all), this is printed
to the kernel log:

  [   10.497333] saa7146 (0): dma buffer size 192512
  [   10.497335] dvbdev: DVB: registering new adapter (KNC1 DVB-C TDA10024)
  [   10.545007] adapter failed MAC signature check
  [   10.545009] encoded MAC from EEPROM was
  [   10.545010] ff:
  [   10.545011] ff:
  [   10.545011] ff:
  ...
  [   10.545021] ff
  [   10.832422] budget_av: KNC1-4: MAC addr = 00:09:d6:6d:b3:be

with the 'ff' being repeated for a total of 20 times. Improve that by
using the %*phC format specifier instead dprintk()'ing every byte of the
encoded MAC separately. This obsoletes the int i, and the kernel log
looks cleaner:

  [ 3234.383153] saa7146 (0): dma buffer size 192512
  [ 3234.383154] dvbdev: DVB: registering new adapter (KNC1 DVB-C TDA10024)
  [ 3234.428745] adapter failed MAC signature check
  [ 3234.428747] encoded MAC from EEPROM was ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff:ff
  [ 3234.728194] budget_av: KNC1-0: MAC addr = 00:09:d6:6d:b3:be
Signed-off-by: NDaniel Scheller <d.scheller@gmx.net>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The soc-camera framework is deprecated, patches for it are very rare
and only contain trivial clean up. Further I haven't got any more
soc-camera systems running modern kernels.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

According to the Devicetree Specification, "ok" is not a valid status.

Fixes: 47c71bd6 ("[media] rcar_vin: add devicetree support")
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: NNiklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Clearly, changeset 95ce9c28 ("media: v4l: common: Add a
function to obtain best size from a list") was never tested, as it
broke compilation with:

drivers/media/platform/vivid/vivid-vid-cap.c: In function ‘vivid_try_fmt_vid_cap’:
drivers/media/platform/vivid/vivid-vid-cap.c:565:34: error: macro "v4l2_find_nearest_size" requer 6 argumentos, mas apenas 5 foram fornecidos
             mp->width, mp->height);
                                  ^
drivers/media/platform/vivid/vivid-vid-cap.c:564:4: error: ‘v4l2_find_nearest_size’ undeclared (first use in this function); did you mean ‘__v4l2_find_nearest_size’?
    v4l2_find_nearest_size(webcam_sizes, width, height,
    ^~~~~~~~~~~~~~~~~~~~~~
    __v4l2_find_nearest_size
drivers/media/platform/vivid/vivid-vid-cap.c:564:4: note: each undeclared identifier is reported only once for each function it appears in
drivers/media/i2c/ov5670.c: In function ‘ov5670_set_pad_format’:
drivers/media/i2c/ov5670.c:2233:48: error: macro "v4l2_find_nearest_size" requer 6 argumentos, mas apenas 5 foram fornecidos
           fmt->format.width, fmt->format.height);
                                                ^
drivers/media/i2c/ov5670.c:2232:9: error: ‘v4l2_find_nearest_size’ undeclared (first use in this function); did you mean ‘__v4l2_find_nearest_size’?
  mode = v4l2_find_nearest_size(supported_modes, width, height,
         ^~~~~~~~~~~~~~~~~~~~~~
         __v4l2_find_nearest_size
drivers/media/i2c/ov13858.c: In function ‘ov13858_set_pad_format’:
drivers/media/i2c/ov13858.c:1379:48: error: macro "v4l2_find_nearest_size" requer 6 argumentos, mas apenas 5 foram fornecidos
           fmt->format.width, fmt->format.height);
                                                ^
drivers/media/i2c/ov13858.c:1378:9: error: ‘v4l2_find_nearest_size’ undeclared (first use in this function); did you mean ‘__v4l2_find_nearest_size’?
  mode = v4l2_find_nearest_size(supported_modes, width, height,
         ^~~~~~~~~~~~~~~~~~~~~~
         __v4l2_find_nearest_size
drivers/media/i2c/ov13858.c:1378:9: note: each undeclared identifier is reported only once for each function it appears in

Basically, v4l2_find_nearest_size() callers pass 5 arguments,
while its definition require 6 args.

Unfortunately, my build process was also broken, as it was reporting me that
the compilation went fine:

	$ make ARCH=i386  CF=-D__CHECK_ENDIAN__ CONFIG_DEBUG_SECTION_MISMATCH=y C=1 W=1 CHECK='compile_checks' M=drivers/staging/media
	$ make ARCH=i386  CF=-D__CHECK_ENDIAN__ CONFIG_DEBUG_SECTION_MISMATCH=y C=1 W=1 CHECK='compile_checks' M=drivers/media

	*** ERRORS ***

	*** WARNINGS ***
	compilation succeeded

That was due to a change here to use of linux-log-diff script that
provides a diffstat between the errors output. Somehow, the logic
was missing some fatal errors.

Fixes: 95ce9c28 ("media: v4l: common: Add a function to obtain best size from a list")
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

Replace "cant" with "can't".
"cant" is not same as "Can not" or "Can't".
Signed-off-by: NArushi Singhal <arushisinghal19971997@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

The atomisp_compat_ioctl32() code has problems. This patch disables the
compat_ioctl32 support until those issues have been fixed.

Contact Sakari or me for more details.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org>      # for v4.12 and up
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>

This patch fix the following build warnings:
  CC [M]  drivers/staging/media/atomisp/pci/atomisp2/atomisp_drvfs.o
cc1: warning: drivers/staging/media/atomisp/pci/atomisp2/css2400/isp/kernels/bayer_ls/bayer_ls_1.0/: No such file or directory [-Wmissing-include-dirs]
cc1: warning: drivers/staging/media/atomisp/pci/atomisp2/css2400/isp/kernels/io_ls/plane_io_ls/: No such file or directory [-Wmissing-include-dirs]
cc1: warning: drivers/staging/media/atomisp/pci/atomisp2/css2400/isp/kernels/io_ls/yuv420_io_ls/: No such file or directory [-Wmissing-include-dirs]
cc1: warning: drivers/staging/media/atomisp/pci/atomisp2/css2400/isp/kernels/ipu2_io_ls/plane_io_ls/: No such file or directory [-Wmissing-include-dirs]
cc1: warning: drivers/staging/media/atomisp/pci/atomisp2/css2400/isp/kernels/ipu2_io_ls/yuv420_io_ls/: No such file or directory [-Wmissing-include-dirs]
cc1: warning: drivers/staging/media/atomisp/pci/atomisp2/css2400/isp/kernels/s3a_stat_ls/: No such file or directory [-Wmissing-include-dirs]
cc1: warning: drivers/staging/media/atomisp/pci/atomisp2/css2400/isp/kernels/scale/: No such file or directory [-Wmissing-include-dirs]
cc1: warning: drivers/staging/media/atomisp/pci/atomisp2/css2400/isp/kernels/scale/scale_1.0/: No such file or directory [-Wmissing-include-dirs]
cc1: warning: drivers/staging/media/atomisp/pci/atomisp2/css2400/isp/kernels/yuv_ls: No such file or directory [-Wmissing-include-dirs]
cc1: warning: drivers/staging/media/atomisp/pci/atomisp2/css2400/isp/kernels/yuv_ls/yuv_ls_1.0/: No such file or directory [-Wmissing-include-dirs]
by removing the inclusion of such directories
Signed-off-by: NCorentin Labbe <clabbe@baylibre.com>
Signed-off-by: NSakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@s-opensource.com>