The Rx port checksum error counter was incrementing incorrectly with
UDP encapsulated tunneled traffic.  This patch fixes the problem so that
the port_rx_csum counter will show accurate statistics.
Signed-off-by: NAnjali Singhai <anjali.singhai@intel.com>
Signed-off-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When the driver was polling with interrupts disabled the hardware
will occasionally not write back descriptors.  This patch causes
the driver to detect this situation and force an interrupt to
fire which will flush the stuck descriptor.  Does not conflict
with napi because if we are already polling the napi_schedule is
ignored.  Additionally the extra interrupts are rate limited, so
don't cause a burden to the CPU.

Change-ID: Iba4616d2a71288672a5f08e4512e2704b97335e8
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

I didn't notice that return in the code, fix it by
adding a goto out instead to free the memory.

Fixes:

> New smatch warnings:
> drivers/net/ethernet/intel/i40e/i40e_debugfs.c:832 i40e_dbg_dump_desc() warn: possible memory leak of 'ring'
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NJim Young <james.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The current implementations all use dev_uc_add_excl() and such whose API
doesn't support vlans, so we can't make it with NICs HW for now.

Fixes: f6f6424b ('net: make vid as a parameter for ndo_fdb_add/ndo_fdb_del')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inline functions are preferred over macros when they can be used
interchangeably.

CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reported-by: NJoe Perches <joe@perches.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a little more state context to an NVM update debug message.

Change-ID: I512160259052bcdbe5bdf1adf403ab2bf7984970
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Decoding the AQ return code is great except when the AQ send timed out
and there's no return code set.  This changes the handy decoder
interface to help catch and properly report the condition as a useful
errno rather than returning a misleading '0'.

Change-ID: I07a1f94f921606da49ffac7837bcdc37cd8222eb
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Only poll on the NVM semaphore if there's time left on a previous
reservation.  Also, add a little more info to debug messages.

Change-ID: I2439bf870b95a28b810dcb5cca1c06440463cf8a
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The state transitions after an error were not managed well, so
these changes get us back to the INIT state or don't transition
out of the INIT state after most errors.

Change-ID: I90aa0e4e348dc4f58cbcdce9c5d4b7fd35981c6c
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't bother trying to set a smaller timeout on the polling,
just simplify the code and always use the max limit.  Also,
rename a variable for clarity and fix a comment.

Change-ID: I0300c3562ccc4fd5fa3088f8ae52db0c1eb33af5
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The nvm_semaphore_wait field is set but never used, so let's
just get rid of it.

Change-ID: I2107bd29b69f99b1a61d7591d087429527c9d8fa
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The adminq init is run after the EMPR that is triggered by the
NVM update.  The final write command will cause the reset and
will want to wait for the ARQ event that signals the end of the
update, but the reset precludes the event being sent.  The state
is probably already at INIT, but we set it so here anyway, and
clear the release_on_done flag as well.

Change-ID: Ie9d724a39e71f988741abc3d51b4cb198c7e0272
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Acked-by: NKamil Krawczyk <kamil.krawczyk@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Just to be sure, add a range check to avoid any possible
array index-out-of-bound issues.

CC: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Change-ID: I9323bee6732c2a47599816e1d6c6b3a1f8dcbf54
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NMichal Kosiarz <michal.kosiarz@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Rework the debug messages in the NVM update state machine so that we can
turn them on and off dynamically rather than forcing a recompile/reload.

These can now be turned on with something like:
	ethtool -s eth1 msglvl 0xf000008f
and off with:
	ethtool -s eth1 msglvl 0xf000000f

The high 0xf0000000 gets the driver's attention that we want to change the
internal debug flags, and the 0x80 bit is the NVM debug.

Change-ID: I5efb9039400304b29a0fd6ddea3f47bb362e6661
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The NVM update operations take time finish asynchronously, and follow-on
update requests need to wait for the current one to finish.  Early
firmware didn't handle this well, so the code had to track the busy state.
The released firmware handles the busy state correctly, returning
I40E_AQ_RC_EBUSY if an update is still in progress, so the code no longer
needs to track this.

Change-ID: I6e6b4adc26d6dcc5fd7adfee5763423858a7d921
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add more detail to the NVM update error messages so folks
have a better chance at diagnosing issues without having to
resort to heroic measures to reproduce an issue.

Change-ID: I270d1a9c903baceaef0bebcc55d29108ac08b0bd
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Once in a great while the NVMUpdate tools and the driver get out
of phase with each other.  This gives us a way to reset things
without having to unload the driver.

Change-ID: I353f688236249a666a90ba3e7233e0ed8c1a04e9
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update the Intel Ethernet drivers to use eth_skb_pad() and skb_put_padto
instead of doing their own implementations of the function.

Also this cleans up two other spots where skb_pad was called but the length
and tail pointers were being manipulated directly instead of just having
the padding length added via __skb_put.

Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Acked-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reduce stack use by using kmemdup and not using a very
large struct on stack.

In function ‘i40e_dbg_dump_desc’:
warning: the frame size of 8192 bytes is larger than 2048 bytes [-Wframe-larger-than=]
Signed-off-by: NJoe Perches <joe@perches.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump version.

Change-ID: I4264e81dcfb57ec46a3ede54b0a6cb25b497d3cb
Signed-off-by: NCatherine Sullivan <catherine.sullivan@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Getting the pf_id from the function number was a good place to start,
but when the PF was setup in passthru mode, the PCI bus/device/function
was virtualized and the number in the VM is different from the number in
the bare metal.  This caused HW configuration issues when the wrong pf_id
was used to set up the HMC and other structures.  The PF_FUNC_RID register
has the real bus/device/function information as configured by the BIOS,
so use that for a better number.  This works in NPAR mode as well.

Change-ID: I65e3dd6c97594890c2bad566b83cc670b1dae534
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Acked-by: NKevin Scott <kevin.c.scott@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ARQ needs to have at least as many entries as VFs, or the VFs will
get errors from the FW when they send messages to the PF. Since we don't
know how many VFs we'll end up with, just set up 128 descriptors.

Change-ID: I04ae3d1c7faf09110eb782214e9c05aeb62a6c59
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There is an order in which this should happen. It turns out that FW will
not let you change the Loopback setting of the VSI with update VSI prior
to the VEB creation.

Change-ID: I7614ddff8b4c37702930c02f16f8c346aaa64bd1
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

All VSIs on a VEB should either have loopback enabled or disabled, a
mixed mode is not supported for a VEB. Since our driver supports multiple
VSIs per PF that need to talk to each other make sure to enable Loopback
for the PF and FDIR VSI as well.

Also, we now have to explicitly enable Loopback mode otherwise we fail
VSI creation for VMDq and VF VSIs.

Change-ID: Ib68c3ea4aeb730ac9468f930610de456efbe5b20
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Increase reset delay to ensure all internal caches are properly flushed
in worst case scenario.

Change-ID: I6f059a9e024fbf9ef1debd32497eed21369957fc
Signed-off-by: NKevin Scott <kevin.c.scott@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The old xxx_NETDEV_STAT() macro was defined long before the newer
rtnl_link_stats64 came into being, and just never got updated.  Since we're
using rtnl_link_stats64 in other parts of the driver, we should use it
here as well.  We've just been lucky that the field definitions are the
same sizes.

Change-ID: I19fc71619905700235dcdf0d3c8153aec81d36de
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch is useful for future expansion when new VF MAC types get
added. It helps with cleaning up VF driver flow.

Change-ID: Ibe1eeb71262a3a40f24a1c5409436bdc3411da7f
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add the Virtual Channel OP event opcode for CONFIG_RSS, so that the
Virtual Channel state machine can properly decipher status change events.

Change-ID: I09939c7aa380147f60c49fd01ef2e27d0dc1c299
Signed-off-by: NAnjali Singhai Jain <anjali.singhai@intel.com>
Acked-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Resolve an issue related to images with multiple PFs per physical
port. We cannot fully support 1588 PTP features, since only one port
should control (ie: write) the registers at a time. Doing so can cause
interference of functionality.

It may be possible to partially implement the API for only those
features without side effects. However, this at minimum means non
controlling PFs lose Tx timestamps, frequency atunement, and possibly
SYSTIME adjustment. There may be further impact I did not discover.
Since the API in the kernel expects these features to work, it is
simpler and less dangerous to just disable PTP features on all PFs not
identified as the controlling PF in PRTTSYN_CTL0.PF_ID.

This change also removes the warning printed when hwtstaml IOCTL is
called on the wrong PF. This is actually meaningless now, since only one
PF per port will support it. In addition, the ethtool get_ts_info IOCTL
was updated so that only the controlling port will even indicate support
(so as not to confuse users).

The overall downside is complete loss of functionality on non
controlling PF, vs the possible gain of partial support. The biggest
factor for choosing this approach is simplicity and ensuring that the
main PF will work. There could easily be other portions of the 1588
logic with side effects I am not aware, and the reduced functionality
that might be made available is significantly less useful. In addition,
the API does not allow for proper indication of why particular features
are not supported. These reasons are enough to decide for the simpler
approach to resolving this issue.

Change-ID: If4696bae686fc18aef6552b67dd417213d987c16
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NJim Young <jamesx.m.young@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds additional text description for base pf0 and flow director
generated interrupts.  Without this patch, these interrupts are difficult
to distinguish per port on a multi-function device.

Change-ID: I4662e1b38840757765a3fe63d90219d28e76bfab
Signed-off-by: NCarolyn Wyborny <carolyn.wyborny@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Use the 'i' rather than the more restrictive 'x' or 'd' in the aq_cmd
arguments.  This makes the user interface much more forgiving and user
friendly.

Change-ID: I5dcd57b9befc047e06b74cf1152a25a3fa9e1309
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This message really doesn't give any useful information and ends up
getting printed every service_task loop in the Linux driver, filling the
logfile with noise when AQ tracing is enabled.  This patch simply removes
the noise.

Change-ID: I30ad51e6b03c7ad12a7d9c102def0087db622df3
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This case statement is empty and the fall through just breaks out
so remove the break and let it fall through to break out.

Change-ID: I1b5ba9870d5245ca80bfca6e7f5f089e2eb8ccb0
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

So this can be reused for identification of other "items" as well.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Reviewed-by: NThomas Graf <tgraf@suug.ch>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Do the work of parsing NDA_VLAN directly in rtnetlink code, pass simple
u16 vid to drivers from there.
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Acked-by: NAndy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: NJamal Hadi Salim <jhs@mojatatu.com>
Acked-by: NJohn Fastabend <john.r.fastabend@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The original FDB code submission wasn't correct and the code
wasn't enabled.  This removes some dead code (can use the common kernel
code for fdb_del and fdb_dump) and correctly enables the fdb_add
function pointer.

The fdb_add functionality is important to i40e because it is needed
for a workaround to allow bridges to work correctly on the i40e
hardware.
Reported-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Acked-by: NGreg Rose <gregory.v.rose@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NJiri Pirko <jiri@resnulli.us>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we want the SW INT to go off as soon as possible, write the
extra bits that will turn off the ITR wait for the interrupt.

Change-ID: I6d5382ba60840fa32abb7dea17c839eb4b5f68f7
Signed-off-by: NShannon Nelson <shannon.nelson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Overloading the msg_size field in the arq_event_info struct is just a
bad idea. It leads to repeated bugs when the structure is used in a
loop, since the input value (buffer size) is overwritten by the output
value (actual message length).

Fix this by splitting the field into two and renaming to indicate the
actual function of each field.

Since the arq_event struct has now changed, we need to change the drivers
to support this. Note that we no longer need to initialize the buffer size
each time we go through a loop as this value is no longer destroyed by
arq processing.

In the process, we also fix a bug in i40evf_verify_api_ver where the
buffer size was not correctly reinitialized each time through the loop.

Change-ID: Ic7f9633cdd6f871f93e698dfb095e29c696f5581
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Acked-by: NShannon Nelson <shannon.nelson@intel.com>
Acked-by: NAshish Shah <ashish.n.shah@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to DCBX configuration change if the VSI needs to use more than 1 TC;
it needs to disable the XPS maps that were set when operating in 1 TC mode.
Without disabling XPS the netdev layer will select queues based on those
settings and not use the TC queue mapping to make the queue selection.

This patch allows the driver to enable/disable the XPS based on the number
of TCs being enabled for the given VSI.

Change-ID: Idc4dec47a672d2a509f6d7fe11ed1ee65b4f0e08
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When PFC is enabled we should not proceed with setting the link flow control
parameters.  Also, always report the link flow Tx/Rx settings as off when
PFC is enabled.

Change-ID: Ib09ec58afdf0b2e587ac9d8851a5c80ad58206c4
Signed-off-by: NNeerav Parikh <neerav.parikh@intel.com>
Tested-By: NJack Morgan <jack.morgan@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>