adapt drivers/s390/net/Kconfig to current IBM wording
and further cosmetics
Signed-off-by: NPeter Tiedemann <ptiedem@de.ibm.com>
Signed-off-by: NUrsula Braun <braunu@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Rearrange functions to allow removal of some forward declarations.
Make certain global functions static along the way.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Make needlessly global functions static.  In a couple of cases this
requires removing forward declarations and reordering functions.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add some debug printks if we encounter a potentially bad receive
return descriptor.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use netif_msg_* for console messages emitted by the driver. Add a
parameter to allow control of messaging at driver startup, and also
add the ability to control it with ethtool.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use skb->csum_start for tx checksum offload preparation. Also swap
the variables css and cso so they hold the intended values of csum
start and offset, respectively.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The transmit packet descriptor consists of four 32-bit words, with word 3
upper bits overloaded depending upon the condition of its bits 3 and 4.
The driver currently duplicates all word 2 and some word 3 register bit
definitions unnecessarily and also uses a set of nested structures in its
definition of the TPD without good cause. This patch adds a lengthy
comment describing the TPD, eliminates duplicate TPD bit definitions,
and simplifies the TPD structure itself. It also expands the TSO check
to correctly handle custom checksum versus TSO processing using the revised
TPD definitions. Finally, shorten some variable names in the transmit
processing path to reduce line lengths, rename some variables to better
describe their purpose (e.g., nseg versus m), and add a comment or two
to better describe what the code is doing.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add the ethtool register dump option to the atl1 driver.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The L1 tx packet descriptor expects TCP Header Length to be expressed as a
number of 32-bit dwords.  The atl1 driver uses tcp_hdrlen() to populate the
field, but tcp_hdrlen() returns the header length in bytes, not in dwords.
Add a shift to convert tcp_hdrlen() to dwords when we write it to the tpd.

Also, some of our bit assignments are made to the wrong tpd words.  Change
those to the correct words.

Finally, since all this fixes TSO, enable TSO by default.
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Acked-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The future atl2 driver and the existing atl1 driver can share certain
functions and definitions.  Move these shareable functions and definitions
out of atl1-specific files and into atlx.c and atlx.h.  Some transitory
hackery will be present until atl2 is merged.

Reduce the number of source files by moving ethtool, hw, and param
functions from separate files into atl1_main.c, then rename it to just
atl1.c.

Move all atl1-specific definitions from atl1_hw.h to atl1.h.

Finally, clean up to make checkpatch.pl happy.
Signed-off-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

In preparation for a future Atheros L2 NIC driver (called atl2), relocate
the atl1 driver into a new /drivers/net/atlx directory that will ultimately
be shared with the future atl2 driver.
Signed-off-by: NChris Snook <csnook@redhat.com>
Signed-off-by: NJay Cliburn <jacliburn@bellsouth.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

The xircom_tulip_cb driver has been replaced the xircom_cb driver, and
since it depended on BROKEN_ON_SMP it e.g. was no longer present in many
distribution kernels.

This patch therefore removes it.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

All the hardware supported by this driver is now supported
by the skge driver. The last remaining issue was support for ancient
dual port SysKonnect fiber boards, and the skge driver now does these
correctly (p.s. sk98lin was always broken on these old dual port
boards anyway).
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/kyle/parisc-2.6:
  [PARISC] make ptr_to_pide() static
  [PARISC] head.S: section mismatch fixes
  [PARISC] add back Crestone Peak cpu
  [PARISC] futex: special case cmpxchg NULL in kernel space
  [PARISC] clean up show_stack
  [PARISC] add pa8900 CPUs to hardware inventory
  [PARISC] clean up include/asm-parisc/elf.h
  [PARISC] move defconfig to arch/parisc/configs/
  [PARISC] add back AD1889 MAINTAINERS entry
  [PARISC] pdc_console: fix bizarre panic on boot
  [PARISC] dump_stack in show_regs
  [PARISC] pdc_stable: fix compile errors
  [PARISC] remove unused pdc_iodc_printf function
  [PARISC] bump __NR_syscalls
  [PARISC] unbreak pgalloc.h
  [PARISC] move VMALLOC_* definitions to fixmap.h
  [PARISC] wire up timerfd syscalls
  [PARISC] remove old timerfd syscall

Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

- move boot_args[] into the init section
- move $global$ into the read_mostly section
- fix the following two section mismatches:
WARNING: vmlinux.o(.text+0x9c): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
WARNING: vmlinux.o(.text+0xa0): Section mismatch: reference to .init.text:start_kernel (between '$pgt_fill_loop' and '$is_pa20')
Signed-off-by: NHelge Deller <deller@gmx.de>
SIgned-off-by: NKyle McMartin <kyle@mcmartin.ca>

Crestone Peak Slow is the 800MHz PA-8800 cpu in the C8000.
0x88B is probably the Crestone Peak Fast.
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

Commit a0c1e907 added code to futex.c
to detect whether futex_atomic_cmpxchg_inatomic was implemented at run
time:

+       curval = cmpxchg_futex_value_locked(NULL, 0, 0);
+       if (curval == -EFAULT)
+               futex_cmpxchg_enabled = 1;

This is bogus on parisc, since page zero in kernel virtual space is the
gateway page for syscall entry, and should not be read from the kernel.
(That, and we really don't like the kernel faulting on its own address
 space...)
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

When we show_regs, we obviously have a struct pt_regs of the calling
frame. Use these in show_stack so we don't have the entire bogus call trace
up to the show_stack call.
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

This patch adds the known pa8900 CPUs to the inventory list and removes
the Crestone Peak one which apparently never escaped into the wild.
Signed-off-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

Cleanup some cruft. No functionality changes.
Signed-off-by: NRandolph Chung <tausq@parisc-linux.org>
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

This patch moves the default parisc defconfig to
arch/parisc/configs/generic_defconfig where it belongs and selects it as
the default defconfig through KBUILD_DEFCONFIG.
Signed-off-by: NAdrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

Signed-off-by: NThibaut VARENE <T-Bone@parisc-linux.org>
Signed-off-by: NKyle McMartin <kyle@mcmartin.ca>

Commit 721fdf34 introduced a subtle bug
by accidently removing the "static" from iodc_dbuf. This resulted in, what
appeared to be, a trap without *current set to a task. Probably the result of
a trap in real mode while calling firmware.

Also do other misc clean ups. Since the only input from firmware is non
blocking, share iodc_dbuf between input and output, and spinlock the
only callers.
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

Originally, show_stack was used in BUG() output. However, a recent commit
changed it to print register state (no idea what that's supposed to help,
really...) and parisc was missing a backtrace because of it.
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

Signed-off-by: NJoel Soete <rubisher@scarlet.be>
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

oops, forgot this in the previous commit.
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

Commit 2f569afd broke the compile
rather spectacularly. Fix code errors.
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

They make way more sense here, really...
Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

Signed-off-by: NKyle McMartin <kyle@parisc-linux.org>

This essentially reverts commit 71fc47a9
("ACPI: basic initramfs DSDT override support"), because the code simply
isn't ready.

It did ugly things to the init sequence to populate the rootfs image
early, but that just ended up showing other problems with the whole
approach.  The fact is, the VFS layer simply isn't initialized this
early, and the relevant ACPI code should either run much later, or this
shouldn't be done at all.

For 2.6.25, we'll just pick the latter option.  We can revisit this
concept later if necessary.

Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Thomas Renninger <trenn@suse.de>
Cc: Eric Piel <eric.piel@tremplin-utc.net>
Cc: Len Brown <len.brown@intel.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Markus Gaugusch <dsdt@gaugusch.at>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

DATA_CARRY is not boolean
Signed-off-by: NRoel Kluin <12o3l@tiscali.nl>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
  [NET]: Fix tbench regression in 2.6.25-rc1

Use the existing calc_delta_mine() calculation for sched_slice(). This
saves a divide and simplifies the code because we share it with the
other /cfs_rq->load users.

It also improves code size:

      text    data     bss     dec     hex filename
     42659    2740     144   45543    b1e7 sched.o.before
     42093    2740     144   44977    afb1 sched.o.after
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>

Fair sleepers need to scale their latency target down by runqueue
weight. Otherwise busy systems will gain ever larger sleep bonus.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>

Currently we schedule to the leftmost task in the runqueue. When the
runtimes are very short because of some server/client ping-pong,
especially in over-saturated workloads, this will cycle through all
tasks trashing the cache.

Reduce cache trashing by keeping dependent tasks together by running
newly woken tasks first. However, by not running the leftmost task first
we could starve tasks because the wakee can gain unlimited runtime.

Therefore we only run the wakee if its within a small
(wakeup_granularity) window of the leftmost task. This preserves
fairness, but does alternate server/client task groups.
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

lw->weight can be 0 for a short time during bootup.
Signed-off-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>