The coherentio variable has previously been used as a boolean value,
indicating whether the user specified that coherent I/O should be
enabled or disabled. It failed to take into account the case where the
user does not specify any preference, in which case it makes sense that
we should default to coherent I/O if the hardware supports it
(hw_coherentio is non-zero).

Introduce an enum to clarify the 3 different values of coherentio & use
it throughout the code, modifying plat_device_is_coherent() &
r4k_cache_init() to take into account the default case.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/14347/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Introduce support for PCI drivers using only functionality provided
generically by the PCI subsystem, by adding the minimum arch-provided
functions required.

The driver this has been developed for & tested with the xilinx-pcie on
a MIPS Boston development board.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14346/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Introduce 2 Kconfig symbols, CONFIG_PCI_DRIVERS_GENERIC &
CONFIG_PCI_DRIVERS_LEGACY, which indicate whether the system should be
built to for PCI drivers using the MIPS-specific struct pci_controller
API (hereafter "legacy" drivers) or more generic drivers using only
functionality provided by the PCI core (hereafter "generic" drivers).

The Kconfig entries are created such that platforms have to select
CONFIG_PCI_DRIVERS_GENERIC if they wish to use it - that is, the default
is CONFIG_PCI_DRIVERS_LEGACY so that existing platforms need no
modification.

The functions declared in pci.h are rearranged with those provided only
by pci-legacy.c being guarded by an #ifdef CONFIG_PCI_DRIVERS_LEGACY to
ensure they are only used in configurations where they are implemented.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14345/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Split out the parts of pci.c that are used by existing systems with
MIPS-style PCI drivers but that will not be used by systems with more
generic PCI drivers such as pcie-xilinx. This is done in preparation for
allowing configurations where the code moved to pci-legacy.c is not
built.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: Paul Burton <paul.burton@imgtec.com>
Patchwork: https://patchwork.linux-mips.org/patch/14344/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The MIPS implementation of pcibios_assign_all_busses trivially returns
1. Implement it as a static function in asm/pci.h such that the compiler
can inline it & optimise out never-taken paths.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14343/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

In preparation for allowing configurations in which pcibios_init is not
included, make pcibios_set_cache_line_size an initcall. arch_initcall is
used such that it runs before the pcibios_init subsys_initcall for
platforms that continue to use it.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14342/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Introduce support for CONFIG_PCI_DOMAINS_GENERIC, allowing for platforms
to make use of generic PCI domains instead of the MIPS-specific
implementation. The set_pci_need_domain_info function is introduced to
abstract away the removed need_domain_info field in struct
pci_controller, and pcibios_scanbus is adjusted to use the pci_domain_nr
accessor instead of directly accessing the index field.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14341/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Rather than open-coding a linked list implementation, make use of the
one in linux/list.h.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14340/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Current instruction decoder for uprobe/kprobe handler only handles
branches with delay slots. For compact branches the behaviour is rather
unpredictable - and depending on the encoding of a compact branch
instruction may result in one (or more) of:
- executing an instruction that follows a branch which wasn't in a delay
  slot and shouldn't have been executed
- incorrectly emulating a branch leading to a jump to a wrong location
- unexpected branching out of the single-stepped code and never reaching
  the breakpoint that should terminate the probe handler

Results of these actions are generally unpredictable, but can end up
with a probed application or kernel crash, so disable placing probes on
compact branches until they are handled properly.
Signed-off-by: NMarcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14336/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Currently both kprobes and uprobes code have definitions of the
insn_has_delay_slot method. Move it to a separate header as an inline
method that each probe-specific method can later use.
No functional change intended, although the methods slightly varied in
the constraints they set for the methods - the uprobes one was chosen as
it is slightly more specific when filtering opcode fields.
Signed-off-by: NMarcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14335/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Use appended DTB when available.
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/14337/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Changes node names of the interrupt-controller device nodes to
interrupt-controller instead of label strings.
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14004/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Adds NAND device nodes to BCM7xxx MIPS based SoCs.
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14003/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Adds SDHCI device nodes to BCM7xxx MIPS based SoCs.
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14002/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Adds GPIO device nodes to BCM7xxx MIPS based SoCs.
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14001/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Adds PWM device nodes to BCM7xxx MIPS based SoCs.
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Cc: Jonas Gorski <jonas.gorski@gmail.com>
Cc: Kevin Cernekee <cernekee@gmail.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: MIPS Mailing List <linux-mips@linux-mips.org>
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14000/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The arch code will hang the machine with an infinite loop if the board
doesn't provide an impelementation of halt - let it, rather than
duplicating it.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14280/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Make use of the generic syscon-reboot driver to reboot the Malta board,
reducing the amount of platform code it requires.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Stephan Linz <linz@li-pro.net>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14279/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add the DT nodes required to probe the CFI compatible parallel monitor
flash found on the Malta development board, and remove the platform
code that was previously doing it. Delete the now-empty malta-platform.c
file. Adjust the Malta defconfigs that enable MTD & the pflash/CFI
driver to enable CONFIG_MTD_PHYSMAP_OF rather than CONFIG_MTD_PHYSMAP in
order to preserve their behaviour.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14278/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add the DT node required to probe the RTC, and remove the platform code
that was previously doing it.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14277/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Since commit 44a7185c ("of/platform: Add common method to populate
default bus") the Malta publish_devices initcall has essentially been a
no-op. Remove it.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14276/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Since commit 44a7185c ("of/platform: Add common method to populate
default bus") platforms calling of_platform_bus_probe from an initcall
is either a rather unsafe race with of_platform_default_populate_init or
a no-op. The MIPS Malta board needs to probe devices under an ISA bus,
which we do support in the of_busses array but until now haven't
included in of_default_bus_match_table.

Add an "isa" entry to of_default_bus_match_table such that we can just
accept use of of_platform_default_populate_init & remove the
Malta-specific match table in a later patch.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NRob Herring <robh@kernel.org>
Cc: Frank Rowand <frowand.list@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14275/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Probe the CPU, GIC & i8259 interrupt controllers present in the Malta
system using device tree. This enables interrupts to be provided to
devices using device tree as they are moved over to being probed using
it.

Since Malta is very configurable it's unknown whether a GIC will be
present at compile time. In order to support both cases the
malta_dt_shim code is added in order to detect whether a GIC is present,
adjusting the DT to route interrupts correctly and nop out the GIC node
if no GIC is found.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: devicetree@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14274/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Malta boards can have more than 256MB DDR available, but we have
previously only made use of up to 256MB (ie. the DDR accessible via
kseg0) by default, without the user manually specifying mem= kernel
parameters. This patch causes all available DDR, as reported by the
bootloader via the ememsize or memsize environment variables or
optionally on the command line, to be used when possible without the
user needing to manually provide the memory ranges.

Malta now has 2 subtly different memory maps which have to be taken into
account when setting this up. The original memory map (referred to by
the code as v1) has up to 2GB of DDR aliased in both the upper & lower
halves of the 32 bit physical address space, with a 256MB I/O region
obscuring 0x10000000-0x1fffffff only in the lower alias. The revised v2
memory map is flat with up to 4GB DDR starting from 0x0, and the I/O
region obscures 256MB of DDR which becomes inacessible. The memory map
in use is indicated by a register provided by the rocit2 system
controller, which is checked in order to set up the kernels memory
ranges accordingly.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14273/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Set the PCI_BAR0 register in all configurations such that PCI devices
can perform DMA to all of the bottom 2GB of the physical address space.
This is imperfect if we make use of the legacy Malta memory map, but it
is an improvement on the inconsistent values setup before.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14272/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The i8259A_irq_pending function is unused. Remove the dead code.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14271/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The default i8259 polling function (i8259_irq) is nicely generic but is
fairly costly. Platforms often provide an alternative means of polling
for an i8259 interrupt, and when using the i8259 without device tree
have typically just chained its parent interrupt to their own handler
function. In order to allow for platform-specific polling functions to
be used in cases where the driver is probed via device tree, provide an
i8259_set_poll function that accepts a pointer to an alternative poll
function that will override the default.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14270/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Mapping the parent IRQ will use a virq number which may conflict with
the hardcoded I8259A_IRQ_BASE..I8259A_IRQ_BASE+15 range that the i8259
driver expects to be free. If this occurs then we'll hit errors when
adding the i8259 IRQ domain, since one of its virq numbers will already
be in use.

Avoid this by adding the i8259 domain before mapping the parent IRQ,
such that the i8259 virq numbers become used before the parent interrupt
controller gets a chance to use any of them.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14269/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The SEAD3 board defines a custom implementation of read_persistent_clock
which does exactly the same dummy operation as the generic weak version.
Remove the not really implemented custom version.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14064/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Probe the img-ascii-lcd driver using device tree in order to display a
message on the SEAD3 board's LCD display, and remove the platform code
that was formerly performing this function. This removes more platform
code and moves SEAD3 further towards being entirely DT-based.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14063/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add a driver for simple ASCII LCD displays found on the MIPS Boston,
Malta & SEAD3 development boards. The Boston display is an independent
memory mapped device with a simple memory mapped 8 byte register space
containing the 8 ASCII characters to display. The Malta display is
exposed as part of the Malta board registers, and provides 8 registers
each of which corresponds to one of the ASCII characters to display. The
SEAD3 display is slightly more complex, exposing an interface to an
S6A0069 LCD controller via registers provided by the boards CPLD.
However although the displays differ in their register interface, we
require similar functionality on each board so abstracting away the
differences within a single driver allows us to share a significant
amount of code & ensure consistent behaviour.

The driver displays the Linux kernel version as the default message, but
allows the message to be changed via a character device. Messages longer
then the number of characters that the display can show will scroll.

This provides different behaviour to the existing LCD display code for
the MIPS Malta or MIPS SEAD3 platforms in the following ways:

  - The default string to display is not "LINUX ON MALTA" or "LINUX ON
    SEAD3" but "Linux" followed by the version number of the kernel
    (UTS_RELEASE).

  - Since that string tends to be significantly longer it scrolls twice
    as fast, moving every 500ms rather than every 1s.

  - The LCD won't be updated until the driver is probed, so it doesn't
    provide the early "LINUX" string.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Miguel Ojeda Sandonis <miguel.ojeda.sandonis@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14062/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Add documentation for a devicetree binding for the simple ASCII LCD
displays found on development boards such as the MIPS Boston, MIPS Malta
& MIPS SEAD3 from Imagination Technologies.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NRob Herring <robh@kernel.org>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: David S. Miller <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14061/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The SEAD3 board no longer uses the cobalt_lcdfb driver, so remove the
SEAD3-specific code from it.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Ondrej Zary <linux@rainbow-software.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Simon Horman <horms+renesas@verge.net.au>
Cc: linux-mips@linux-mips.org
Cc: linux-fbdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14060/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The 2 line * 16 character LCD display on the SEAD3 board has no real use
as a framebuffer device. It's far too small to produce any meaningful
output if used as the kernel console, SEAD3 is a development board that
will essentially always have a far more useful UART connection & the
code in sead3-display.c will overwrite whatever's on the display every
second anyway. Remove this unused code.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14059/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Parse the memsize argument provided by the bootloader in the DT shim
code, allowing the user to override it on the command line. This places
all of the DT manipulation code into sead3-dtshim.c.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Kefeng Wang <wangkefeng.wang@huawei.com>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14058/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove the custom platform code to restart when instructed to power off,
instead relying upon the generic restart-poweroff driver probed via DT
to do the same thing.

Remove also the halt implementation, which is incorrect. The generic
MIPS version will hang the system as halt should.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14057/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Remove the SEAD3 implementation of _machine_restart & instead make use
of the generic syscon-reboot driver probed via device tree.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14056/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Probe a driver for the PLED & FLED LEDs found on the SEAD3 board using
the register-bit-led driver via device tree, rather than a custom driver
via platform code. Enable support for the register-bit-led driver & its
prerequisite syscon in sead3_defconfig.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14054/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Probe the system parallel flash using device tree rather than platform
code, in order to reduce the amount of the latter.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-mips@linux-mips.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14053/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

The SEAD-3 board is now probing its EHCI controller using the generic
EHCI driver & its generic-ehci device tree binding. Remove the unused
SEAD-3 specific EHCI code.
Signed-off-by: NPaul Burton <paul.burton@imgtec.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/14052/Signed-off-by: NRalf Baechle <ralf@linux-mips.org>