[Why]
EDID emulation didn't work properly for linux, as we stop programming
if nothing is connected physically.

[How]
We get a flag from DRM when we want to do edid emulation. We check if
this flag is true and nothing is connected physically, if so we only
program the front end using VIRTUAL_SIGNAL.
Signed-off-by: NBhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: NHarry Wentland <Harry.Wentland@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

[Why]
There have been a few reports of Vega10 display remaining blank
after S3 resume. The regression is caused by workaround for mode
change on Vega10 - skip set_bandwidth if stream count is 0.
As a result we skipped dispclk reset on suspend, thus on resume
we may skip the clock update assuming it hasn't been changed.
On some systems it causes display blank or 'out of range'.

[How]
Revert "drm/amd/display: Fix Vega10 black screen after mode change"
Verified that it hadn't cause mode change regression.
Signed-off-by: NRoman Li <Roman.Li@amd.com>
Reviewed-by: NSun peng Li <Sunpeng.Li@amd.com>
Acked-by: NLeo Li <sunpeng.li@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

The vce cancel_delayed_work_sync never be called.
driver call the function in error path.

This caused the A+A suspend hang when runtime pm enebled.
As we will visit the smu in the idle queue. this will cause
smu hang because the dgpu has been suspend, and the dgpu also
will be waked up. As the smu has been hang, so the dgpu resume
will failed.
Reviewed-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NFeifei Xu <Feifei.Xu@amd.com>
Signed-off-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

This reverts commit 0c08754b.

commit 0c08754b
("drm/panel: Add device_link from panel device to DRM device")
creates a circular dependency under these circumstances:

1. The panel depends on dsi-host because it is MIPI-DSI child
   device.
2. dsi-host depends on the drm parent device (connector->dev->dev)
   this should be allowed.
3. drm parent dev (connector->dev->dev) depends on the panel
   after this patch.

This makes the dependency circular and while it appears it
does not affect any in-tree drivers (they do not seem to have
dsi hosts depending on the same parent device) this does not
seem right.

As noted in a response from Andrzej Hajda, the intent is
likely to make the panel dependent on the DRM device
(connector->dev) not its parent. But we have no way of
doing that since the DRM device doesn't contain any
struct device on its own (arguably it should).

Revert this until a proper approach is figured out.

Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927124130.9102-1-linus.walleij@linaro.org

We attempt to get fences earlier in the hopes that everything will
already have fences and no callbacks will be needed.  If we do succeed
in getting a fence, getting one a second time will result in a duplicate
ref with no unref.  This is causing memory leaks in Vulkan applications
that create a lot of fences; playing for a few hours can, apparently,
bring down the system.

Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107899Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJason Ekstrand <jason@jlekstrand.net>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180926071703.15257-1-jason.ekstrand@intel.com

When we want to writeback to memory in NV12 format we need to program
the RGB2YUV coefficients. Currently, we don't program the coefficients
and NV12 doesn't work at all.

This patchset fixes that by programming a sane default(bt709, limited
range) as rgb2yuv coefficients.

In the long run, probably we need to think of a way for userspace to
be able to program that, but for now I think this is better than not
working at all or not advertising NV12 as a supported format for
memwrite.

Changes since v1:
 - Write the rgb2yuv coefficients only once, since we don't change
   them at all, just write them the first time NV12 is programmed,
   suggested by Brian Starkey, here [1]

[1] https://lists.freedesktop.org/archives/dri-devel/2018-August/186819.htmlSigned-off-by: NAlexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: NLiviu Dudau <liviu.dudau@arm.com>
Signed-off-by: NLiviu Dudau <liviu.dudau@arm.com>

Currently, if userspace calls drm_wait_vblank before the crtc is
activated the crtc vblank_enable hook is called, which in case of
malidp driver triggers some warninngs. This happens because on
device init we don't inform the drm core about the vblank state
by calling drm_crtc_vblank_on/off/reset which together with
drm_vblank_get have some magic that prevents calling drm_vblank_enable
when crtc is off.
Signed-off-by: NAlexandru Gheorghe <alexandru-cosmin.gheorghe@arm.com>
Acked-by: NLiviu Dudau <liviu.dudau@arm.com>
Signed-off-by: NLiviu Dudau <liviu.dudau@arm.com>

Because CRAT_CU_FLAGS_IOMMU_PRESENT was not set in some BIOS crat, we
need to workaround this.

For future compatibility, we also overwrite the bit in capability according
to the value of needs_iommu_device.
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NYong Zhao <Yong.Zhao@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

CWSR fails on Raven if the control stack is MTYPE_UC, which is used
for regular GART mappings. As a workaround we map it using MTYPE_NC.

The MEC firmware expects the control stack at one page offset from the
start of the MQD so it is part of the MQD allocation on GFXv9. AMDGPU
added a memory allocation flag just for this purpose.
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NYong Zhao <yong.zhao@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

A wrong register bit was examinated for checking SDMA status so it reports
false failures. This typo only appears on gfx_v7. gfx_v8 checks the correct
bit.
Acked-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NAmber Lin <Amber.Lin@amd.com>
Reviewed-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NFelix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Commit 19be5570 ("drm/ttm: add operation ctx to ttm_bo_validate v2")
introduced a regression where the vmwgfx driver refused to evict a
buffer that was still busy instead of waiting for it to become idle.

Fix this.

Cc: <stable@vger.kernel.org>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: NChristian König <christian.koenig@amd.com>

If framebuffers are larger, we create bounce surfaces that are within
STDU limits.
Signed-off-by: NDeepak Rawat <drawat@vmware.com>
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>

For all display units, limit mode size exposed to texture_max_width/
height as this is the maximum framebuffer size that virtual device can
create.
Signed-off-by: NDeepak Rawat <drawat@vmware.com>
Reviewed-by: NSinclair Yeh <syeh@vmware.com>
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>

For STDU individual screen target size is limited by
SVGA_REG_SCREENTARGET_MAX_WIDTH/HEIGHT registers so add that limit
during atomic check_modeset.

An additional limit is placed in the update_layout ioctl to avoid
requesting layouts that current user-space typically can't support.
Also modified the comments to reflect current limitation on topology.
Signed-off-by: NDeepak Rawat <drawat@vmware.com>
Reviewed-by: NSinclair Yeh <syeh@vmware.com>
Reviewed-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>

During atomic check to prepare the new topology no need to check if
old_crtc_state was enabled or not. This will cause atomic_check to fail
because due to connector routing a crtc can be in atomic_state even if
there was no change to enable status.

Detected this issue with igt run.
Signed-off-by: NDeepak Rawat <drawat@vmware.com>
Reviewed-by: NSinclair Yeh <syeh@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>

Add new pci id.
Reviewed-by: NRex Zhu <Rex.Zhu@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org

The A64 HDMI PHY seems to be not able to use the second video PLL as
clock parent in experiments.

Drop the support for the second PLL from A64 HDMI PHY driver.

Fixes: b46e2c9f ("drm/sun4i: Add support for A64 HDMI PHY")
Signed-off-by: NIcenowy Zheng <icenowy@aosc.io>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180916043409.62374-2-icenowy@aosc.io

When one vgpu is destroyed, its ggtt entries are not cleared.
This patch clears ggtt entries to avoid information leak.

v2: add 'Fixes' tag (Zhenyu)

Fixes: 2707e444 ("drm/i915/gvt: vGPU graphics memory virtualization")
Signed-off-by: NZhipeng Gong <zhipeng.gong@intel.com>
Reviewed-by: NHang Yuan <hang.yuan@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>

Fix the suspicious RCU usage issue in intel_vgpu_emulate_mmio_write.
Here need to request the srcu read lock of kvm->srcu before doing
gfn_to_memslot(). The detailed log is as below:
[  218.710688] =============================
[  218.710690] WARNING: suspicious RCU usage
[  218.710693] 4.14.15-dd+ #314 Tainted: G     U
[  218.710695] -----------------------------
[  218.710697] ./include/linux/kvm_host.h:575 suspicious rcu_dereference_check() usage!
[  218.710699]
               other info that might help us debug this:

[  218.710702]
               rcu_scheduler_active = 2, debug_locks = 1
[  218.710704] 1 lock held by qemu-system-x86/2144:
[  218.710706]  #0:  (&gvt->lock){+.+.}, at: [<ffffffff816a1eea>] intel_vgpu_emulate_mmio_write+0x5a/0x2d0
[  218.710721]
               stack backtrace:
[  218.710724] CPU: 0 PID: 2144 Comm: qemu-system-x86 Tainted: G     U 4.14.15-dd+ #314
[  218.710727] Hardware name: Dell Inc. OptiPlex 7040/0Y7WYT, BIOS 1.1.1 10/07/2015
[  218.710729] Call Trace:
[  218.710734]  dump_stack+0x7c/0xb3
[  218.710739]  gfn_to_memslot+0x15f/0x170
[  218.710743]  kvm_is_visible_gfn+0xa/0x30
[  218.710746]  intel_vgpu_emulate_gtt_mmio_write+0x267/0x3c0
[  218.710751]  ? __mutex_unlock_slowpath+0x3b/0x260
[  218.710754]  intel_vgpu_emulate_mmio_write+0x182/0x2d0
[  218.710759]  intel_vgpu_rw+0xba/0x170 [kvmgt]
[  218.710763]  intel_vgpu_write+0x14d/0x1a0 [kvmgt]
[  218.710767]  __vfs_write+0x23/0x130
[  218.710770]  vfs_write+0xb0/0x1b0
[  218.710774]  SyS_pwrite64+0x73/0x90
[  218.710777]  entry_SYSCALL_64_fastpath+0x25/0x9c
[  218.710780] RIP: 0033:0x7f33e8a91da3
[  218.710783] RSP: 002b:00007f33dddc8700 EFLAGS: 00000293

v2: add 'Fixes' tag, refine log format.(Zhenyu)
Fixes: cc753fbe ("drm/i915/gvt: validate gfn before set shadow page")
Reviewed-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NWeinan Li <weinan.z.li@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>

Host prints lots of untracked MMIO at 0x4653c when creating linux guest.
"gvt: vgpu 2: untracked MMIO 0004653c len 4"

GEN9_CLKGATE_DIS_4 (0x4653c) is accessed by i915 for gmbus clockgating.
However vgpu doesn't support any clockgating powergating operations
on related mmio access trap so need add it to default handler.
GEN9_CLKGATE_DIS_4 is accessed in bxt_gmbus_clock_gating() which only
applies to GEN9_LP so doens't show the warning on other platforms.

The solution is to add it to default handler init_bxt_mmio_info().
Reviewed-by: NHe, Min <min.he@intel.com>
Signed-off-by: NColin Xu <colin.xu@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>

Recent patch fixed the call trace
"ERROR Port B enabled but PHY powered down? (PHY_CTL 00000000)".
but introduced another similar call trace shown as:
"ERROR Port C enabled but PHY powered down? (PHY_CTL 00000200)".
The call trace will appear when host and guest enabled different ports,
i.e. host using PORT C or neither PORT is enabled, while guest is always
using PORT B as simulated by gvt. The issue is actually covered previously
before the commit and reverals now when the commit do the right thing.

On BXT, some PHY registers are initialized by vbios, before i915 loaded.
Later i915 will re-program some, or skip some based on the implementation.
The initialized mmio for guest i915 is done by gvt, based on the snapshot
taken from host. If host and guest have different PORT enabled, some
DPIO PHY mmios that gvt initialized for guest i915 will not match the
simualted monitor for guest, which leads to guest i915 print the calltrace
when it's trying to enable PHY and PORT.

The solution is to init these DPIO PHY registers to default value, then
guest i915 will program them to reasonable value based on the default
powerwell table and enabled PORT. Together with the old patch, all similar
call trace in guest kernel on BXT can be resolved.

v2: Move PHY register init to intel_vgpu_reset_mmio (Min)
v3: Do not delete empty line in issue fix patch. (zhenyu)

Fixes: c8ab5ac3 ("drm/i915/gvt: Make correct handling to vreg
BXT_PHY_CTL_FAMILY")
Reviewed-by: NHe, Min <min.he@intel.com>
Signed-off-by: NColin Xu <colin.xu@intel.com>
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>

As pointed out by Daniel Vetter, we should be usinng
drm_drv_uses_atomic_modeset() for determining whether or not we want to
make the debugfs nodes for atomic instead of checking DRIVER_ATOMIC, as
the former isn't an accurate representation of whether or not the driver
is actually using atomic modesetting internally (even though it might
not be exposing atomic capabilities).
Signed-off-by: NLyude Paul <lyude@redhat.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180917173733.21293-1-lyude@redhat.com

The etnaviv device is a virtual device backing the DRM device, which may
drive multiple hardware GPU core devices. As most of the dma-mapping handling
is done through the virtual device, we need to make sure that a proper DMA
setup is in place. The easiest way to get a reasonable configuration is
to let the virtual device share the DMA configuration with one of the GPU
devices, so call of_dma_configure() with the right parameters manually.

This assumes that all etnaviv driven GPU devices in the system share the
same DMA configuration. If we ever encounter a SoC where the GPUs are on
busses with different offsets or behind different IOMMUs that will require
much deeper changes to the driver, as we would need to implement etnaviv
specific versions of most of the DRM helper functions.

For now we should be fine with this solution.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Tested-by: NGuido Günther <agx@sigxcpu.org>
Tested-by: NEugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>

The recent change of vga_switcheroo allowed the runtime PM for
HD-audio on AMD GPUs, but this also resulted in a regression.  When
the HD-audio controller driver gets runtime-suspended, HD-audio link
is turned off, and the hotplug notification is ignored.  This leads to
the inconsistent audio state (the connection isn't notified and ELD is
ignored).

The best fix would be to implement the proper ELD notification via the
audio component, but it's still not ready.  As a quick workaround,
this patch adds the check of runtime_idle and allows the runtime
suspend only when the vga_switcheroo is bound with discrete GPU.
That is, a system with a single GPU and APU would be again without
runtime PM to keep the HD-audio link for the hotplug notification and
ELD read out.

Also, the codec->auto_runtime_pm flag is set only for the discrete GPU
at the time GPU gets bound via vga_switcheroo (i.e. only dGPU is
forcibly runtime-PM enabled), so that APU can still get the ELD
notification.

For identifying which GPU is bound, a new vga_switcheroo client
callback, gpu_bound, is implemented.  The vga_switcheroo simply calls
this when GPU is bound, and tells whether it's dGPU or APU.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=200945
Fixes: 07f4f97d ("vga_switcheroo: Use device link for HDA controller")
Reported-by: NJian-Hong Pan <jian-hong@endlessm.com>
Tested-by: NJian-Hong Pan <jian-hong@endlessm.com>
Acked-by: NLukas Wunner <lukas@wunner.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Messed up when sending pull request and sent an outdated version of
previous patch, this fixes it up to remove warnings.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Fixes gcc '-Wunused-but-set-variable' warning:

drivers/gpu/drm/drm_fb_helper.c: In function 'drm_pick_crtcs':
drivers/gpu/drm/drm_fb_helper.c:2373:43: warning:
 variable 'connector_funcs' set but not used [-Wunused-but-set-variable]
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1536722130-108819-1-git-send-email-yuehaibing@huawei.com

Slowly leaking memory one page at a time :)
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NAndrey Grodzovsky <andrey.grodzovsky@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Given that we are now reasonably confident in our ability to detect and
reserve the stolen memory (physical memory reserved for graphics by the
BIOS) for ourselves on most machines, we can put it to use. In this
case, we need a page to hold the overlay registers.

On an i915g running MythTv, H Buus noticed that

	commit 6a2c4232
	Author: Chris Wilson <chris@chris-wilson.co.uk>
	Date:   Tue Nov 4 04:51:40 2014 -0800
	drm/i915: Make the physical object coherent with GTT

introduced stuttering into his video playback. After discarding the
likely suspect of it being the physical cursor updates, we were left
with the use of the phys object for the overlay. And lo, if we
completely avoid using the phys object (allocated just once on module
load!) by switching to stolen memory, the stuttering goes away.

For lack of a better explanation, claim victory and kill two birds with
one stone.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107600
Fixes: 6a2c4232 ("drm/i915: Make the physical object coherent with GTT")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180906190144.1272-1-chris@chris-wilson.co.uk
(cherry picked from commit c8124d39)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

since we use PSP to program IH regs now
Signed-off-by: NMonk Liu <Monk.Liu@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NEmily Deng <Emily.Deng@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Fix SDMA hang in prt mode, clear XNACK_WATERMARK in reg SDMA0_UTCL1_WATERMK to avoid the issue

Affected ASICs: VEGA10 VEGA12 RV1 RV2

v2: add reg clear for SDMA1
Signed-off-by: NTao Zhou <tao.zhou1@amd.com>
Tested-by: NYukun Li <yukun1.li@amd.com>
Reviewed-by: NHawking Zhang <Hawking.Zhang@amd.com>
Acked-by: NChristian König <christian.koenig@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

Avoid unlocking a lock we never locked.
Signed-off-by: NChristian König <christian.koenig@amd.com>
Reviewed-by: NJunwei Zhang <Jerry.Zhang@amd.com>
Signed-off-by: NAlex Deucher <alexander.deucher@amd.com>

This fixes a NULL pointer dereference that can happen if the UDL
driver is unloaded before the framebuffer is initialized. This can
happen e.g. if the USB device is unplugged right after it was plugged
in.

As explained by Stéphane Marchesin:

It happens when fbdev is disabled (which is the case for Chrome OS).
Even though intialization of the fbdev part is optional (it's done in
udlfb_create which is the callback for fb_probe()), the teardown isn't
optional (udl_driver_unload -> udl_fbdev_cleanup ->
udl_fbdev_destroy).

Note that udl_fbdev_cleanup *tries* to be conditional (you can see it
does if (!udl->fbdev)) but that doesn't work, because udl->fbdev is
always set during udl_fbdev_init.

Cc: stable@vger.kernel.org
Suggested-by: NSean Paul <seanpaul@chromium.org>
Reviewed-by: NSean Paul <seanpaul@chromium.org>
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NEmil Lundmark <lndmrk@chromium.org>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180528142711.142466-1-lndmrk@chromium.orgSigned-off-by: NSean Paul <seanpaul@chromium.org>

Two patches from the R40 display pipeline support series weren't applied
with the rest of the series. When they did get applied, the -rc6
deadline for drm-misc-next had past, so they didn't get into 4.19-rc1
with the rest of the series. However, the two patches are crucial in
the parsing of the R40's display pipeline graph in the device tree.
Without them, the driver crashes because it can't follow the odd graph
structure.

This patch removes the R40 compatibles from the sun4i-drm driver,
effectively disabling DRM support for the R40 for one release cycle.
This will prevent the driver from crashing upon probing.

The compatibles should be reinstated for the next release.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NMaxime Ripard <maxime.ripard@bootlin.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180827083950.602-1-wens@csie.orgSigned-off-by: NSean Paul <seanpaul@chromium.org>

We prefer to of_device_id tables are NULL terminated. So make
vexpress_muxfpga_match is NULL terminated.
Signed-off-by: Nzhong jiang <zhongjiang@huawei.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/1533379767-15629-1-git-send-email-zhongjiang@huawei.comSigned-off-by: NSean Paul <seanpaul@chromium.org>

When there's no scaling requested ->is_unity should be true no matter
the format.

Also, when no scaling is requested and we have a multi-planar YUV
format, we should leave ->y_scaling[0] to VC4_SCALING_NONE and only
set ->x_scaling[0] to VC4_SCALING_PPF.

Doing this fixes an hardly visible artifact (seen when using modetest
and a rather big overlay plane in YUV420).

Fixes: fc04023f ("drm/vc4: Add support for YUV planes.")
Cc: <stable@vger.kernel.org>
Signed-off-by: NBoris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: NEric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/20180725122907.13702-1-boris.brezillon@bootlin.comSigned-off-by: NSean Paul <seanpaul@chromium.org>

During IPS disabling the current 42ms timeout value leads to occasional
timeouts, increase it to 100ms which seems to get rid of the problem.

References: https://bugs.freedesktop.org/show_bug.cgi?id=107494
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=107562Reported-by: NDiego Viola <diego.viola@gmail.com>
Tested-by: NDiego Viola <diego.viola@gmail.com>
Cc: Diego Viola <diego.viola@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180905100005.7663-1-imre.deak@intel.com
(cherry picked from commit acb3ef0ee40ea657280a4a11d9f60eb2937c0dca)
Signed-off-by: NRodrigo Vivi <rodrigo.vivi@intel.com>

Fixes eDP backlight issues on more recent laptops.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

If a HPD pulse signalling the need to retrain the link occurs between
the KMS driver releasing the output and the supervisor interrupt that
finishes the teardown, it was possible get a NULL-ptr deref.

Avoid this by marking the link as inactive earlier.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

We need to do this earlier to prevent aux channel timeouts in resume
paths on certain systems.
Signed-off-by: NBen Skeggs <bskeggs@redhat.com>

Signed-off-by: NBen Skeggs <bskeggs@redhat.com>